SK1501

SK15XX Family 1:5 Signal Distribution HIGH-PER.ORMANCE PRODUCTS PRELIMINARY SK15XX .amily .unctional Block Diagram OUT0 OUT0* IN IN* DQ D* Q* 0 1 OUT1 OUT1* CLK CLK* SEL* SEL OUT2 OUT2* OUT3 OUT3* OUT4 OUT4* Revision 1/ January 23, 2001 1 www.semtech.com SK15XX Family 1:5 Signal Distribution HIGH-PER.ORMANCE PRODUCTS SK15XX .amily Product Selection Guide 1:5 Signal Distribution 3 GHz Logic .amily Power Supply Open Emitter l l l l l Output Configuration 50Ω Double Termination Internal Current Sink (Double Termination) ECL / PECL Double Swing / TTL ECL / PECL ECL / PECL ECL / PECL Now Now Now Now Now Output Availability PRELIMINARY Synch / Asynch Operation Product 3.3V 5.2V 50Ω Source Termination SK1500 SK1501 SK1502 SK1503 SK1504 l l l l l l l l l Logic / Translation .amily Translation Product SK1525 SK1526 SK1527 SK1528 SK1529 SK1530 Anything to PECL Anything to ECL Anything to PECL Anything to ECL Anything to PECL Anything to ECL Open Emitter l l l l l l Output Configuration 50Ω Double Termination 50Ω Source Termination Availability Now Now Now Now Now Now Open Collector Logic .amily Output Configuration Product SK1599 Open Collector l 12 mA Q2 2001 Output Current Availability Revision 1/ January 4, 2001 2 www.semtech.com SK15XX Family 1:5 Signal Distribution HIGH-PER.ORMANCE PRODUCTS SK15XX .amily Package Information 5mm x 5mm TQ.P 3 PRELIMINARY D, E D1, E1 2 4 See Figure 3. b 8 Top View e A A2 SEATING PLANE A1 10 b Side View Revision 1/ January 4, 2001 3 www.semtech.com SK15XX Family 1:5 Signal Distribution HIGH-PER.ORMANCE PRODUCTS SK15XX .amily Package Information (continued) 5mm x 5mm TQ.P 9 02 PRELIMINARY 7 b WITH PLATING 2 R1 9 9 e/2 01 R2 S GAGE PLANE 03 11 L 00 (L1) 25 c c1 9 b1 b Figure 1. Figure 2. Figure 3. JEDEC Variation All Dimensions in Millimeters 1. All dimensions and tolerancing conforms to ANSI Y14.5M-1982. 2. The top package body size may be smaller than the bottom package body size by as much as 0.15 mm. 3. To be determined at seating plane. 4. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. D1 and E1 are maximum plastic body size dimensions including mold mismatch. 5. Details of Pin 1 identifier optional, but must be located within the zone indicated. 6. All dimensions are in millimeters. 7. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall not cause the lead width to exceed the maximum b dimension by more than 0.08 mm. Dambar cannot be located on the lower radius or the foot. Minimum space between protrusion and an adjacent lead is 0.07 mm for 0.4 mm and 0.5 mm pitch packages. 8. Exact shape of each corner is optional. 9. These dimensions apply to the flat section of the lead between 0.10 mm and 0.25 mm from the lead tip. 10. A1 is defined as the distance from the seating plane to the lowest point of the package body. Revision 1/ January 23, 2001 4 Symbol A A1 A2 D D1 E E1 N e b b1 R1 R2 00 01 02 03 S c c1 L L1 aaa bbb ccc ddd MIN 1.00 0.05 0.95 NOM 1.10 0.10 1.00 7.00 BSC 5.00 BSC 7.00 BSC 5.00 BSC 32 0.50 BSC MAX 1.20 0.15 1.05 Note Comments Package Stand Off Height Air Gap Package Body Thickness 3 4, 2 3 4, 2 Package Body Width Lead Count Lead Pitch 0.27 0.23 – 0.20 7 Lead Thickness Package Body Length 0.17 0.17 0.08 0.08 0 o o o o 0.22 0.20 – – 3.5 – 12 12 – – – 0.60 1.00 RE. 0.20 0.20 0.08 0.08 o o o 7 o 0 – 13 13 – 0.20 0.16 0.75 o o 11 11 0.20 0.09 0.09 0.45 www.semtech.com SK15XX Family 1:5 Signal Distribution HIGH-PER.ORMANCE PRODUCTS Absolute Maximum Ratings* Symbol VEE VCC VI VI IOUT TA Tstg Tsol Parameter Power Supply (VCC = 0V) Power Supply (VEE = 0V) Input Voltage (VCC = 0V, VI not more negative than VEE) Input Voltage (VE = 0V, VI not more positive than VCC) Output Current Continuous Surge Operating Temperature Range Storage Temperature Solder Temperature (