GBU601

GBU6005 THRU GBU610 GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIERS Reverse Voltage – 50 to 1000 Volts Forward Current – 6.0 Amperes Features • Plastic material has Underwriters Laboratory Flammability Classification 94V-0 • Ideal for printed circuit boards • Glass passivated chip junction • Reliable low cost construction utilizing molded plastic technique Mechanical Data • Case: Molded plastic GBU • Terminals: leads solderable per MIL-STD-202 Method 208 guaranteed • Mounting Position: Any Absolute Maximum Ratings and Characteristics Rating at 25℃ ambient temperature unless otherwise specified. Single-phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC = 100℃ (Note 1)， (Note 2) Peak forward surge current，8.3ms single half-sine-wave superimposed on rated load (JEDEC Method) Maximum forward voltage at 3.0A DC and 25℃ Maximum reverse current at TA = 25℃ at rated DC blocking voltage TA = 125℃ Typical junction capacitance (Note 3) Typical thermal resistance (Note 1),(Note 2) Typical thermal resistance (Note 1),(Note 2) Operating and storage temperature range IF(AV) IFSM VF IR CJ RθJA RθJC T J ,T S 211 7.4 2.2 -55 to +150 6 175 1 5 500 94 A A V µA pF ℃/W ℃/W ℃ VRRM VRMS VDC GBU 6005 50 35 50 GBU 601 100 70 100 GBU 602 200 140 200 GBU 604 400 280 400 GBU 606 600 420 600 GBU 608 800 560 800 GBU 610 1000 700 1000 Units V V V Notes: (1). Units case mounted on 2.6x1.4x0.06” thick (6.5x3.5x0.15 cm) AI. plate heatsink.. (2). Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screws. (3). Measured at 1MHz and applied reverse voltage of 4.0 VDC. SEMTECH ELECTRONICS LTD. (Subsidiary of Semtech International Holdings Limited, a company listed on the Hong Kong Stock Exchange, Stock Code: 724) R Dated : 16/02/2004 GBU6005 THRU GBU610 RATINGS AND CHARACTERISTIC CURVES Average Forward Output Current (A) Peak Forward Surge Current (A) Fig.1 Derating Curve Output Rectified Current Heatsink Mounting. 2.6*1.4*0.06" Thk (6.5*3.5*0.15cm) AL. Plate 6.0 175 150 125 100 75 50 Fig.2 Maximum Non-Repetitive Peak Forward Surge Current Per Leg Single Sine-Wave (JEDEC Method) TJ=150°C 4.0 2.0 0 60Hz Resistive or Inductive Load 0 50 100 150 1.0 Cycle 25 1 10 100 Case Temperature (°C) Instantaneous Reverse Current ( A) Fig.3 Typical Forward Characteristics Per Leg Number of Cycles at 60Hz Fig.4 Typical Reverse Leakage Characteristics Per Leg 50 - 400V 600 - 1000V TJ=125°C 10 1 0.1 0.01 TJ=25°C 0 Instantaneous Forward Current (A) 100 500 100 10 TJ=25°C Pulse Width = 300 s 1% Duty Cycle 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 Instantaneous Forward Voltage (V) Fig.5 Typical Junction Capacitance Per Leg TJ=25°C f=1.0MHz Vsig=50mVp-p Percent of Rated Peak Reverse Voltage (%) Fig.6 Typical Transient Thermal Impedance 20 40 60 80 100 Junction Capacitance, pF 1000 Transient Thermal Impedance (°C/W) 100 10 100 1 10 50 - 400V 600 - 1000V 0.1 Reverse Voltage (A) 1 10 100 0.1 0.01 0.1 1 10 100 t,Heating Time (sec.) SEMTECH ELECTRONICS LTD. (Subsidiary of Semtech International Holdings Limited, a company listed on the Hong Kong Stock Exchange, Stock Code: 724) R Dated : 16/02/2004