MUR1620CT

MUR1620CT GLASS PASSIVATED HIGH EFFICENCY RECTIFIER Reverse Voltage – 50 to 1000 Volts Forward Current – 16.0 Amperes Features • Low forward voltage, High current capability • Plastic package has Underwriters Laboratory Flammability Classification 94V-O utilizing Flame Retardant Epoxy Molding Compound. • High surge capacity • Low power loss, high efficiency • Ultra fast recovery times, high voltage Mechanical Data • Case: Molded plastic, TO-220 • Terminals: leads solderable per • MIL-STD-202, method 208 guaranteed • Polarity: As marked • Mounting Position: Any PIN 1 PIN 2 CASE PIN2 Positlve CT Absolute Maximum Ratings and Characteristics Dimensions in mm Ratings at 25℃ ambient temperature unless otherwise specified. Single phase, half wave,60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward Rectified current at TC = 100 ℃ Peak forward surge current 8.3ms single half-sine-wave superimposed on rated load (JEDEC method) Maximum forward voltage at 8.0A and TA = 25℃ Typical junction Capacitance (Note1) Maximum reverse recovery time (Note 2) Typical thermal resistance (Note3) Maximum reverse current at rated DC blocking voltage @TA = 25℃ @TC =125℃ IF(AV) IFSM VF CJ TRR R0JC IR T J ,T s 16.0 125 1.0 80 50 3.0 10 500 -55 to +150 Amps Amps Volts pF nS ℃/W µAmps µAmps ℃ VRRM VRMS VDC Value 200 140 200 Units Volts Volts Volts Operating and storage temperature range Notes :1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC. 2. Reverse recovery test conditions: IF = 0.5A, IR = 1A, IRR = 0.25A 3. Thermal resistance from junction to case per leg mounted on heatsink. SEMTECH ELECTRONICS LTD. ® (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated : 23/06/2003 MUR1620CT FIG.1 Reverse Recovery Time Characteristic and Test Circuit Diagram 50 NONINDUCTIVE 10 NONINDUCTIVE +0.5A DUT (+) 50Vdc (appox) (-) 1 NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (-) PULSE GENERATOR (NOTE 2) (+) -1.0A 1cm SET TIME BASE FOR 5/10ns/cm 0 -0.25A trr NOTES:1. Rise Time=7ns max. Input Impedance= 1 megohm 22 pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms Average Forward Current. (A) Instantaneous Reverse Current. ( A) 20 16 12 8 4 0 0 FIG.2 Muximum Forward Current Derating Curve 1000 FIG.3 Typical Reverse Characteristics Per Leg 100 Tj =125°C 10 Tj =25°C 50 100 150 Case Temperature. (°C) FIG.4 Maximum Non-repetitive Forward Surge Current Per Leg 1 Peak Forward Surge Current. (A) 0.1 120 90 60 30 Tj =25°C 8.3ms Single Half Sine Wave JEDEC Method 20 40 60 80 100 120 140 Percent of Rated Peak Reverse Voltage. (%) FIG.6 Typical Forward Characteristics Per Leg Number of Cycles at 60Hz FIG.5 Typical Junction Capacitance Per Leg Capacitance. (pF) 240 200 160 120 80 40 0 1 2 5 10 20 50 100 200 500 1000 Tj =25°C Instantaneous Forward Current. (A) 1 2 5 10 20 50 100 100 30 10 3.0 1.0 0.3 0.1 0.03 Reverse Voltage. (V) 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 Tj =25°C PULSE WIDTH-300 s 1% DUTY CYCLE Forward Voltage. (V) SEMTECH ELECTRONICS LTD. ® (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated : 23/06/2003