S05A60

S05A30 THRU S05A60 SCHOTTKY BARRIER RECTIFIERS Reverse Voltage – 30 to 60 Volts Forward Current – 10.0 Amperes Features • Plastic package carries Underwriters Laboratory Flammability Classification 94V-0 • Construction utilizes void-free molded plastic technique • Low reverse leakage • High forward surge current capability • High temperature soldering guaranteed: 250℃,0.25”(6.35mm) from case for 10 seconds TO-220AC MAX10.54 3.91 DIA 3.74 2.87 2.62 4.70 4.44 1.27 1.14 3.68 3.43 10.41 9.91 16.13 15.87 2 14.2 13.4 8.89 8.38 29.16 28.40 4.05 3.55 0.94 0.68 2.79 2.54 14.22 13.46 1 PIN Mechanical Data • Case: Molded plastic body, TO-220AC • Terminals: leads solderable per MIL-STD-750, method 2026 • Polarity: As marked • Mounting Position: Any 0.58 0.35 2.67 2.41 5.20 4.95 PIN 1 PIN 2 CASE Dimensions in mm Absolute Maximum Ratings and Characteristics Ratings at 25℃ ambient temperature unless otherwise specified. Single phase half-wave 60Hz, resistive or inductive load. for capacitive load current derate by 20%. Symbols S05A30 S05A40 S05A45 S05A50 S05A60 Units V V V A A Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current Peak forward surge current 8.3mS single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 5.0A Maximum DC reverse current at rated DC blocking voltage Typical junction capacitance (Note 1) Typical thermal resistance (Note 2) Operating junction temperature range storage temperature range TA = 25℃ TA =100℃ VRRM VRMS VDC I(AV) IFSM VF IR CJ RJC TJ TS 30 21 30 40 28 40 45 32 45 10 125 50 35 50 60 42 60 0.55 1.0 30.0 550 3.0 -65 to +125 -65 to +150 0.65 V mA pF ℃/W ℃ ℃ Notes: (1) Measured at 1MHZ and applied reverse voltage of 4.0V D.C . (2) Thermal resistance from Junction to case. SEMTECH ELECTRONICS LTD. ® (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated :18/12/2003 S05A30 THRU S05A60 Fig. 1- Forward Current Derating Curve Peak Forward Surge Current, Amperes 5 125 8.3ms single half sinewave (JEDEC method) Fig.2-Maximum Non-repetitive Peak Forward Surge Current Average Forward Rectified Current, Amperes 4 3 2 1 0 Single Phase Half Wave 60Hz Resistive or Inductive Load 100 75 50 25 0 0 25 50 75 100 125 150 175 Ambient Temperature,°C Fig. 3-Typical Instantaneous Forward Characteristics Instantaneous Reverse Current, Milliamperes 1 Number of Cycles At 60 Hz 10 100 Fig. 4- Typical Reverse Characteristics 100 Instantaneous Forward Current, Amperes 50 10 10 TJ=100°C 1 TJ=75°C 0.1 1 TJ=25°C Pulse Width=300 s 1% Duty Cycle 0.1 S05A30-S05A45 --- S05A50-S05A60 0.01 0.2 0.4 0.6 0.8 1.0 1.1 0.01 TJ=25°C 0.001 Instantaneous Forward Voltage,Volts 0 20 40 60 80 100 Percent of Peak Reverse Voltage,% Transient Thermal Impedance,°c/w Fig. 6- Typical Transient Thermal Impedance 100 4000 Fig. 5- Typical Junction Capacitance TJ=25°C Junction Capacitance, pF 2000 10 200 1 20 0.1 0.1 0.01 0.1 1.0 10 100 Reverse Voltage, Volts 1.0 10 100 t, Pulse Duration, sec. SEMTECH ELECTRONICS LTD. ® (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated :18/12/2003