144SU100A-PCB

144S...-PCB Series Signal conditioned precision pressure transducers FEATURES · 0...70 mbar to 0...10 bar, 0...1 to 0...150 psi, absolute, gage or differential pressure (custom calibrations available) · Barometric pressure ranges · 0...5 V output · Internal supply regulation · Precision temperature compensated and calibrated SERVICE Non-corrosive, non-ionic working fluids, such as dry air and dry gases. Scale: 1 cm 1 inch SPECIFICATIONS Maximum ratings Supply voltage Maximum load current source sink Temperature limits Storage Operating Compensated 144SC...BARO all others Lead temperature (10 sec soldering) Humidity limits pressure inlets only Proof pressure1 144SM... 144SB010... 144SC...BARO 144SU01..., 144SU05... 144SU150... all others January 2005 / 005 ELECTRICAL CONNECTION 7.5...24 V 20 mA 10 mA -55 to 100°C -40 to 85°C -10 to 60°C 0 to 70 °C 300°C 0 - 100 %RH 1.4 bar 16 bar 2 bar 20 psi 250 psi 2x rated pressure 1/5 +Vs 144S...PCB Vout -Vs 7.5 V to 24 V V www.sensortechnics.com 144S...-PCB Series Signal conditioned precision pressure transducers PERFORMANCE CHARACTERISTICS STANDARD DEVICES (unless otherwise noted VS = 8 V, RL > 100 kΩ, tamb = 25°C) Characteristics Operating pressure differential devices 2 Min. 144SM070D-PCB 144SM350D-PCB 144SB001D-PCB 144SB002D-PCB 144SB005D-PCB 144SB010D-PCB 144SB001A-PCB 144SB002A-PCB 144SB005A-PCB 144SU01D-PCB 144SU05D-PCB 144SU15D-PCB 144SU30D-PCB 144SU100D-PCB 144SU15A-PCB 144SU30A-PCB 144SU100A-PCB 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -0.05 4.9 4.9 Typ. Max. 70 350 1 2 5 10 1 2 5 1 5 15 30 100 15 30 100 Unit mbar bar absolute devices3 differential devices2 p si absolute devices3 Zero pressure offset Full scale span 4 0 5.0 5.0 0.1 0.6 0.2 0.15 0.2 0.1 1 70 0.05 0.03 0.05 5.1 5.1 0.5 3.0 1.0 0.6 1.0 %FSO V Full scale output Non-linearity and hysteresis (BSL)5 Thermal effects (0 to 70°C)6 Offset 144SM070...,144SU01... 144SM350...,144SU05... all others Span Long term stability7 Response time (10 to 90 %) Power consumption (no load) Power supply rejection Offset Span ms mW %FSO/V 2/5 January 2005 / 005 www.sensortechnics.com 144S...-PCB Series Signal conditioned precision pressure transducers PERFORMANCE CHARACTERISTICS BAROMETRIC DEVICES8 (unless otherwise noted VS = 8 V, RL > 100 kΩ, tamb = 25°C) Characteristics Operating pressure ranges 3 Min. 144SC0811BARO 144SC1216BARO 800 12 -0.05 4.95 Typ. Max. 1100 16 Unit mbar p si a V %FSO %FSO/10°C ms mW %FSO/V Offset calibration at lowest specified pressure Full scale output Non-linearity and hysteresis5 Long term stability 7 0 5.0 0.05 0.1 0.05 1 70 0.05 5.05 0.1 0.3 Thermal effects (-10 to 60°C)9 Response time (10 to 90 %) Power consumption (no load) Power supply rejection Offset Span 0.05 0.03 Specification notes: 1. 2. 3. 4. 5. 6. 7. 8. Proof pressure is the maximum pressure which may be applied without causing damage to the sensing element. The output signal of all 144S...D-PCB devices is proportional to the pressure applied to port B, relative to port A, e.g. the output signal increases when vacuum is applied to port A relative to port B. The output signal of all 144S...A-PCB and 144SC...BARO devices is proportional to the pressure applied to port A. Full scale span is the algebraic difference between the positive full scale output and the zero pressure offset. Non-linearity refers to the Best Straight Line fit measured for offset pressure, full scale pressure and 1/2 full scale pressure. Thermal effects tested and guaranteed from 0 to 70°C relative to 25°C. All specifications shown are relative to 25°C. Change in output after one year or 1 million pressure cycles. These devices are factory calibrated at sea level. When used at other altitudes the output signal differs from the reading expected when comparing to the pressure given from your local weather station. The weather station always reports the pressure compared to sea level. On that the output signal of the transducer will change 65mV/0.052 psi per 100 feet e.g. 19.7mV/1.18 mbar per 10 m change in altitude. The output signal can be adjusted to sea level reading by turning the offset trimmer. Thermal effects refer to the combined effects of offset and sensitivity shifts, this is true from -10 to 60°C relative to 25°C. 9. January 2005 / 005 3/5 www.sensortechnics.com 144S...-PCB Series Signal conditioned precision pressure transducers OUTPUT CHARACTERISTICS Standard versions Vout V 5 4 3 2 1 Barometric versions Vout V 5 4 3 2 1 0 20 40 60 80 100 % full scale pressure 0 800 12 900 13 14 1000 15 1100 mbar 16 psia OUTLINE DRAWING offset adjust 30.0 14.0 18.3 9.1 span adjust Port B 2 high pressure port 32.0 3 terminals 0.56 diam. 2 x 5.08 typ. NOM 6.0 22.7 +Vs -Vs Vout 12.6 dimensions mm 60.0 52.4 10.7 Port A 3 3.5 diam. 2 x mounting holes mass: 20 g 4/5 4.8 diam. January 2005 / 005 www.sensortechnics.com 144S...-PCB Series Signal conditioned precision pressure transducers ORDERING INFORMATION Operating Pressure Differential/gage devices 0...70 mbar 0...350 mbar 0...1 bar 0...2 bar 0...5 bar 0...10 bar Absolute devices 0...1 bar 0...2 bar 0...5 bar Differential/gage devices 0...1 psi 0...5 psi 0...15 psi 0...30 psi 0...100 psi 0...150 psi Absolute devices 0...15 psi 0...30 psi 0...100 psi Barometric devices 12...16 psia 800...1100 mbar Part Number 144SM070D-PCB 144SM350D-PCB 144SB001D-PCB 144SB002D-PCB 144SB005D-PCB 144SB010D-PCB 144SB001A-PCB 144SB002A-PCB 144SB005A-PCB 144SU01D-PCB 144SU05D-PCB 144SU15D-PCB 144SU30D-PCB 144SU100D-PCB 144SU150D-PCB 144SU15A-PCB 144SU30A-PCB 144SU100A-PCB 144SC1216BARO 144SC0811BARO Custom calibrations available Sensortechnics reserves the right to make changes to any products herein. Sensortechnics does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. January 2005 / 005 5/5 www.sensortechnics.com