24PC0070D6

24PC Series (psi) Unamplified, uncompensated pressure sensors FEATURES · 0...0.5 to 0...250 psi gage or differential · High impedance bridge · Miniature package · Different pinning configurations · Usable for wet/wet applications8 SERVICE All media compatible with port 1: - polyetherimide - silver-filled silicone - silicon nitride - polyetherimide - fluor-silicone - silicon Scale: 1 cm 1 inch port 29: SPECIFICATIONS Maximum ratings Supply voltage Temperature limits Storage Operating Lead temperature (10 sec. soldering) Humidity limits Vibration (0 to 2000 Hz) (qualification tested) Mechanical shock (qualification tested) Proof pressure all 0.5, 1 and 5 psi devices all 15 psi devices all 30 psi devices all 100 psi devices all 250 psi devices February 2005 / 603 1 ELECTRICAL CONNECTION 12 V -55 to +100°C -40 to +85°C 300°C 0...100 %RH Vs 1 4 - Output 20 g sine 2 150 g + 3 20 psi 45 psi 60 psi 200 psi 500 psi 1/4 www.sensortechnics.com 24PC Series (psi) Unamplified, uncompensated pressure sensors PRESSURE SENSOR CHARACTERISTICS Vs = 10.0 ± 0.01 V, tamb = 25°C (unless otherwise noted) Listing 24PCEFAxx 24PCAFAxx 24PCBFAxx 24PCCFAxx 24PCDFAxx 24PCFFAxx 24PCGFAxx Order number 24PC0035xxA 24PC0070xxA 24PC0350xxA 24PC1000xxA 24PC2000xxA 24PC7000xxA 24PC17K0xxA Operating pressure 0 - 0.5 psi (34.5 mbar) 0 - 1 psi (69 mbar) 0 - 5 psi (345 mbar) 0 - 15 psi (1034 mbar) 0 - 30 psi (2068 mbar) 0 - 100 psi (6.9 bar) 0 - 250 psi (17.2 bar) Full-scale span2 Min. Typ. Max. 24 mV 30 mV 85 mV 165 mV 240 mV 156 mV 145 mV 35 mV 45 mV 115 mV 225 mV 330 mV 225 mV 212 mV 46 mV 60 mV 145 mV 285 mV 420 mV 294 mV 280 mV COMMON PERFORMANCE CHARACTERISTICS Vs = 10.0 ± 0.01 V, tamb = 25°C (unless otherwise noted) Characteristics Zero pressure offset Temperature effects (0 - 50°C)4 Temperature effects on bridge impedance4 Linearity (P2 > P1, BSL)3 Repeatability and hysteresis5 Long term stability7 Input impedance Output impedance Response time6 Specification notes: Min. -30 Offset Span Typ. ±2.0 -2000 +2200 ±0.25 ±0.15 ±0.5 5.0 5.0 Max. +30 Unit mV ppm/°C ±1.0 % sp a n 6.0 6.0 1.0 kΩ ms 4.0 4.0 1. The maximum specified pressure which may be applied to the sensor without causing a permanent change in the output characteristics. 2. Span is the algebraic difference between the output voltage at full-scale pressure and the output at zero pressure. Span is ratiometric to the supply voltage. 3. Linearity (BSL), the deviation of measured output at constant temperature (25°C) from "Best Straight Line" determined by three points, offset pressure, full-scale pressure and half full-scale pressure. V - Voffset [ V½ full scale – { (full full scale pressure) scale x (½ full scale pressure) + Voffset }] : 2 (Vfull scale) x 100 % where: V = measured value for each device 4. Error band of the offset voltage, span or bridge impedance in the specified temperature range, relative to the 25°C reading. 5. Repeatability, the deviation in output readings for successive application of any given input pressure (all other conditions remaining constant. Hysteresis, the error defined by the deviation in output signal obtained when a specific pressure point is approached first with increasing pressure, then with decreasing pressure or vice versa (all other conditions remaining constant). 6. Response time for 0 to full-scale pressure step change, readings taken at 10 % and 90 % of full-scale pressure. 7. Long term stability of offset and span over a period over one year. 8. The sensors might be used on both ports, for media compatible with the components, specified under "Service" (page 1). 9. Other sealing materials are available on request. Minimum order quantities might be required. 10. Other pressure port styles, like barbed ones, luers, modular, M5, needle style or flow through connection, are available on request. For these specials see the data sheet "24/26PC specials". Minimum order quantities might be required, call Sensortechnics for assistance. 2/4 February 2005 / 603 www.sensortechnics.com 24PC Series (psi) Unamplified, uncompensated pressure sensors OUTLINE DRAWINGS10 24PCxxxxG6A (single inline pinning, 1 x 4), gage pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 7,9 2,29 4 x 1,02 P2 1,78 4 x 0,41 4321 3 x 2,54 mass: 2 g 21,8 16,2 9,1 NOM 15,2 12,7 dimensions in mm 24PCxxxxG2A (dual inline pinning, 2 x 2), gage pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 PIN 2 P2 PIN 3 PIN 4 7,9 4 x 1,02 5,1 8,4 12,7 27,9 21,8 16,2 9,1 4 x 0,5 4 x 0,41 mass: 2 g dimensions in mm February 2005 / 603 3/4 www.sensortechnics.com 24PC Series (psi) Unamplified, uncompensated pressure sensors OUTLINE DRAWINGS10 24PCxxxxD6A (single inline pinning, 1 x 4), differential pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 7,9 2,29 4 x 1,02 16,2 9,1 P2 1,78 4 x 0,41 4321 3 x 2,54 34,4 21,8 11,7 mass: 2 g P1 12,7 NOM 15,2 dimensions in mm ORDERING INFORMATION 2 24PC series non compensated Pressure range 0 - 0.5 psi (34.5 mbar) 0 - 1 psi (69 mbar) 0 - 5 psi (345 mbar) 0 - 15 psi (1034 mbar) 0 - 30 psi (2068 mbar) 0 - 100 psi (6.9 bar) 0 - 250 psi (17.2 bar) 4 PC xxxx x x A10 Pressure port (Ø 5.1 mm) Pinning 2: dual inline pinning, 2 x 2 (not available for differential devices) 6: single inline pinning, 1 x 4 Pressure mode D: differential pressure G: gage pressure 0035: 0070: 0350: 1000: 2000: 7000: 17K0: Sensortechnics reserves the right to make changes to any products herein. Sensortechnics does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. 4/4 February 2005 / 603 www.sensortechnics.com