24PC0250G6

24PC Series (mbar) Unamplified, uncompensated pressure sensors FEATURES · 0...50 mbar to 0...16 bar gage or differential · High impedance bridge · Miniature package · Different pinning configurations · Usable for wet/wet applications8 SERVICE All media compatible with port 1: - polyetherimide - silver-filled silicone - silicon nitride - polyetherimide - fluor-silicone - silicon Scale: 1 cm 1 inch port 29: SPECIFICATIONS Maximum ratings Supply voltage Temperature limits Storage Operating Lead temperature (10 sec. soldering) Humidity limits Vibration (0 to 2000 Hz) (qualification tested) Mechanical shock (qualification tested) Proof pressure all 50, 100 and 250 mbar devices all 1 bar devices all 2 bar devices all 5 bar devices all 10 and 16 bar devices June 2005 / 602 1 ELECTRICAL CONNECTION 12 V -55 to +100°C -40 to +85°C 300°C 0...100 %RH Vs 1 4 - Output 20 g sine 2 150 g + 3 1.4 bar 3 bar 4 bar 12 bar 35 bar 1/4 www.sensortechnics.com 24PC Series (mbar) Unamplified, uncompensated pressure sensors PRESSURE SENSOR CHARACTERISTICS Vs = 10.0 ± 0.01 V, tamb = 25°C (unless otherwise noted) Part number 24PC0050xxA 24PC0100xxA 24PC0250xxA 24PC01K0xxA 24PC02K0xxA 24PC05K0xxA 24PC10K0xxA 24PC16K0xxA Operating pressure 0 - 50 mbar 0 - 100 mbar 0 - 250 mbar 0 - 1 bar 0 - 2 bar 0 - 5 bar 0 - 10 bar 0 - 16 bar Full-scale span2 Min. Typ. Max. 21 mV 44 mV 61 mV 159 mV 232 mV 113 mV 84 mV 134 mV 33 mV 66 mV 83 mV 218 mV 320 mV 163 mV 123 mV 197 mV 44 mV 88 mV 105 mV 276 mV 410 mV 215 mV 163 mV 260 mV Sensitivity typ. 660 µV/mbar 660 µV/mbar 333 µV/mbar 220 µV/mbar 160 µV/mbar 32.6 µV/mbar 12.3 µV/mbar 12.3 µV/mbar COMMON PERFORMANCE CHARACTERISTICS Vs = 10.0 ± 0.01 V, tamb = 25°C (unless otherwise noted) Characteristics Zero pressure offset Temperature effects (0 - 50°C)4 Temperature effects on bridge impedance4 Linearity (P2 > P1, BSL)3 Repeatability and hysteresis5 Long term stability7 Input impedance Output impedance Response time6 Offset Span Min. -30 Typ. ±2.0 -2000 +2200 ±0.25 ±0.15 ±0.5 5.0 5.0 Max. +30 Unit mV ppm/°C ±1.0 % sp a n 6.0 6.0 1.0 kΩ ms 4.0 4.0 Specification notes: 1. The maximum specified pressure which may be applied to the sensor without causing a permanent change in the output characteristics. 2. Span is the algebraic difference between the output voltage at full-scale pressure and the output at zero pressure. Span is ratiometric to the supply voltage. 3. Linearity (BSL), the deviation of measured output at constant temperature (25°C) from "Best Straight Line" determined by three points, offset pressure, full-scale pressure and half full-scale pressure. V - Voffset [ V½ full scale – { (full full scale pressure) scale x (½ full scale pressure) + Voffset }] : 2 (Vfull scale) x 100 % where: V = measured value for each device 4. Error band of the offset voltage, span or bridge impedance in the specified temperature range, relative to the 25°C reading. 5. Repeatability, the deviation in output readings for successive application of any given input pressure (all other conditions remaining constant. Hysteresis, the error defined by the deviation in output signal obtained when a specific pressure point is approached first with increasing pressure, then with decreasing pressure or vice versa (all other conditions remaining constant). 6. Response time for 0 to full-scale pressure step change, readings taken at 10 % and 90 % of full-scale pressure. 7. Long term stability of offset and span over a period over one year. 8. The sensors might be used on both ports, for media compatible with the components, specified under "Service" (page 1). 9. Other sealing materials are available on request. Minimum order quantities might be required. 10. Other pressure port styles, like barbed ones, luers, modular, M5, needle style or flow through connection, are available on request. For these specials see the data sheet "24/26PC specials". Minimum order quantities might be required, call Sensortechnics for assistance. 2/4 June 2005 / 602 www.sensortechnics.com 24PC Series (mbar) Unamplified, uncompensated pressure sensors OUTLINE DRAWINGS10 24PCxxxxG6A (single inline pinning, 1 x 4), gage pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 7,9 2,29 4 x 1,02 P2 1,78 4 x 0,41 4321 3 x 2,54 mass: 2 g 21,8 16,2 9,1 NOM 15,2 12,7 dimensions in mm 24PCxxxxG2A (dual inline pinning, 2 x 2), gage pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 PIN 2 P2 PIN 3 PIN 4 7,9 4 x 1,02 5,1 8,4 12,7 27,9 21,8 16,2 9,1 4 x 0,5 4 x 0,41 mass: 2 g dimensions in mm June 2005 / 602 3/4 www.sensortechnics.com 24PC Series (mbar) Unamplified, uncompensated pressure sensors OUTLINE DRAWINGS10 24PCxxxxD6A (single inline pinning, 1 x 4), differential pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 7,9 2,29 4 x 1,02 16,2 9,1 P2 1,78 4 x 0,41 4321 3 x 2,54 34,4 21,8 11,7 mass: 2 g P1 12,7 NOM 15,2 dimensions in mm ORDERING INFORMATION 2 24PC series non compensated Pressure range 0050: 0 - 50 mbar 0100: 0 - 100 mbar 0250: 0 - 250 mbar 01K0: 0 - 1 bar 02K0: 0 - 2 bar 05K0: 0 - 5 bar 10K0: 0 - 10 bar 16K0: 0 - 16 bar 4 PC xxxx x x A10 Pressure port (Ø 5.1 mm) Pinning 2: dual inline pinning, 2 x 2 (not available for differential devices) 6: single inline pinning, 1 x 4 Pressure mode D: differential pressure G: gage pressure Sensortechnics reserves the right to make changes to any products herein. Sensortechnics does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. 4/4 June 2005 / 602 www.sensortechnics.com