26PC0050G6A10

26PC Series (mbar) Temp. compensated and calibrated pressure sensors FEATURES · 0...50 mbar to 0...16 bar gage or differential · High impedance bridge · Miniature package · Different pinning configurations · Usable for wet/wet applications8 SERVICE All media compatible with port 1: - polyetherimide - silver-filled silicone - silicon nitride - polyetherimide - fluor-silicone - silicon Scale: 1 cm 1 inch port 29: SPECIFICATIONS Maximum ratings Supply voltage Temperature limits Storage Operating Lead temperature (10 sec. soldering) Humidity limits Vibration (MIL-STD-202, Meth. 213) 16 V ELECTRICAL CONNECTION -55 to +100°C -40 to +85°C 300°C 0...100 %RH Vs 1 4 - 150 g half sine 11 msec. 150 g Output 2 3 + Mechanical shock (qualification tested) Proof pressure1 all 50, 100 and 250 mbar devices all 1 bar devices all 2 bar devices all 5 bar devices all 10 and 16 bar devices June 2005 / 596 1.4 bar 3 bar 4 bar 12 bar 35 bar 1/4 www.sensortechnics.com 26PC Series (mbar) Temp. compensated and calibrated pressure sensors PRESSURE SENSOR CHARACTERISTICS Vs = 10.0 ± 0.01 V, tamb = 20°C (unless otherwise noted) Part number 26PC0050xxA 26PC0100xxA 26PC0250xxA 26PC01K0xxA 26PC02K0xxA 26PC05K0xxA 26PC10K0xxA 26PC16K0xxA Operating pressure 0 - 50 mbar 0 - 100 mbar 0 - 250 mbar 0 - 1 bar 0 - 2 bar 0 - 5 bar 0 - 10 bar 0 - 16 bar Min. 10.5 mV 20.0 mV 33.5 mV 93.0 mV 91.0 mV 69.0 mV 82.0 mV 133.0 mV Full-scale span2 Typ. 12.0 mV 24.0 mV 36.0 mV 97.0 mV 97.0 mV 72.0 mV 87.0 mV 140.0 mV Max. 13.6 mV 27.0 mV 38.5 mV 100.0 mV 100.0 mV 76.0 mV 92.0 mV 147.0 mV Sensitivity typ. 240 µV/mbar 240 µV/mbar 144 µV/mbar 97 µV/mbar 48.5 mV/bar 14.4 mV/bar 8.7 mV/bar 8.7 mV/bar COMMON PERFORMANCE CHARACTERISTICS Vs = 10.0 ± 0.01 V, tamb = 25°C (unless otherwise noted) Characteristics Zero pressure offset Temperature effects (0 - 50°C)4 Offset all 5 bar devices all other devices all 50 to 1000 mbar devices all 2 bar devices all other devices all 50 and 100 mbar devices all other devices all 50 to 1000 mbar devices all 2 bar devices all other devices Min. -2.0 -1.5 Typ. Max. +2.0 +1.5 Unit Span Linearity (P2 > P1, BSL)3 Repeatability and hysteresis5 Long term stability7 Input impedance Output impedance Response time6 5.5 1.5 ±0.5 ±0.75 ±1.0 ±1.0 ±0.75...±1.0 ±0.25 ±0.1 ±0.1 ±0.2 ±0.5 7.5 2.5 ±1.0 ±1.5 ±2.0 ±2.0 ±1.5 ±0.5 ±0.2 ±0.7 mV % sp a n 11.5 3.0 1.0 kΩ ms Specification notes: 1. The maximum specified pressure which may be applied to the sensor without causing a permanent change in the output characteristics. 2. Span is the algebraic difference between the output voltage at full-scale pressure and the output at zero pressure. Span is ratiometric to the supply voltage. 3. Linearity (BSL), the deviation of measured output at constant temperature (25°C) from "Best Straight Line" determined by three points, offset pressure, full-scale pressure and half full-scale pressure. V - Voffset [ V½ full scale – { (full full scale pressure) scale x (½ full scale pressure) + Voffset }] : 2 (Vfull scale) x 100 % where: V = measured value for each device 4. Error band of the offset voltage, span or bridge impedance in the specified temperature range, relative to the 25°C reading. 5. Repeatability, the deviation in output readings for successive application of any given input pressure (all other conditions remaining constant. Hysteresis, the error defined by the deviation in output signal obtained when a specific pressure point is approached first with increasing pressure, then with decreasing pressure or vice versa (all other conditions remaining constant). 6. Response time for 0 to full-scale pressure step change, readings taken at 10 % and 90 % of full-scale pressure. 7. Long term stability of offset and span over a period over one year. 8. The sensors might be used on both ports, for media compatible with the components, specified under "Service" (page 1). 9. Other sealing materials are available on request. Minimum order quantities might be required. 10. Other pressure port styles, like barbed ones, luers, modular, M5, needle style or flow through connection, are available on request. Minimum order quantities might be required. 2/4 June 2005 / 596 www.sensortechnics.com 26PC Series (mbar) Temp. compensated and calibrated pressure sensors OUTLINE DRAWINGS10 26PCxxxxG6A (single inline pinning, 1 x 4), gage pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 7,9 2,29 4 x 1,02 P2 1,78 4 x 0,41 4321 3 x 2,54 mass: 2 g 21,8 16,2 9,1 NOM 15,2 12,7 dimensions in mm 26PCxxxxG2A (dual inline pinning, 2 x 2), gage pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 PIN 2 P2 PIN 3 PIN 4 7,9 4 x 1,02 5,1 mass: 2 g 27,9 21,8 16,2 9,1 4 x 0,5 12,7 4 x 0,41 8,4 dimensions in mm June 2005 / 596 3/4 www.sensortechnics.com 26PC Series (mbar) Temp. compensated and calibrated pressure sensors OUTLINE DRAWINGS10 26PCxxxxD6A (single inline pinning, 1 x 4), differential pressure devices 12,7 Ø 6,4 Ø 5,1 Ø 1,93 Ø 1,27 PIN 1 7,9 2,29 4 x 1,02 16,2 9,1 P2 1,78 4 x 0,41 4321 3 x 2,54 34,4 21,8 11,7 mass: 2 g P1 12,7 NOM 15,2 dimensions in mm ORDERING INFORMATION 2 26PC series compensated Pressure range 0 - 50 mbar 0 - 100 mbar 0 - 250 mbar 0 - 1 bar 0 - 2 bar 0 - 5 bar 0 - 10 bar 0 - 16 bar Pinning 2: dual inline pinning, 2 x 2 (not available for differential devices) 6: single inline pinning, 1 x 4 6 PC xxxx x x A10 Pressure port (Ø 5.1 mm) 0050: 0100: 0250: 01K0: 02K0: 05K0: 10K0: 16K0: Pressure mode D: differential pressure G: gage pressure Sensortechnics reserves the right to make changes to any products herein. Sensortechnics does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. 4/4 June 2005 / 596 www.sensortechnics.com