RTOP010V7

RTO Series Stainless steel pressure sensors FEATURES · 0...3 to 0...500 psi and -15...15 to -15...100 psi · Absolute and gage pressures · Calibrated and temperature compensated · Rugged stainless steel isolated package · Sensortechnics PRO services SPECIFICATIONS Maximum ratings Supply voltage Temperature ranges: Compensated Operating Storage Vibration: Shock: Life: +15 VDC ELECTRICAL CONNECTION 0 to +82°C -40 to +125°C -40 to +125°C 10 g at 20 to 2000 Hz 100 g for 11 msec. 1 million cycles minimum 100 MΩ at 50 VDC -out +out VsVs+ Insulation resistance (min.): E / 11714 / A 1/6 www.sensortechnics.com RTO Series Stainless steel pressure sensors PRESSURE SENSOR CHARACTERISTICS Part number RTOP003G... RTOP005G... RTOP010G... RTOP015(A,G)... RTOP015V... RTOP030(A,G)... RTOP030V... RTOP050(A,G)... RTOP100(A,G)... RTOP100V... RTOP200(A,G)... RTOP300(A,G)... RTOP500(A,G)... Pressure range 0...3 psig 0...5 psig 0...10 psig 0...15 psi -15...15 psig 0...30 psi -15...30 psig 0...50 psi 0...100 psi -15...100 psig 0...200 psi 0...300 psi 0...500 psi Proof pressure6 9 p si g 1 5 p si g 3 0 p si g 4 5 p si 4 5 p si g 9 0 p si 9 0 p si g 1 5 0 p si 3 0 0 p si 3 0 0 p si g 6 0 0 p si 9 0 0 p si 1 2 0 0 p si Burst pressure7 1 5 p si g 2 5 p si g 4 5 p si g 7 5 p si g 7 5 p si g 1 5 0 p si 1 5 0 p si g 2 5 0 p si 3 0 0 p si 3 0 0 p si g 1 0 0 0 p si 1 5 0 0 p si 2 4 0 0 p si E / 11714 / A 2/6 www.sensortechnics.com RTO Series Stainless steel pressure sensors PERFORMANCE CHARACTERISTICS (VS = 10 VDC ± 0.01 VDC, tamb = 25°C) Characteristics Zero pressure offset all devices up to 10 psi all RTO...A... devices9 all others Full scale span Non-linearity2 Pressure hysteresis2 Thermal effects (0 to 82°C) all others Thermal hysteresis (0 to 82°C) Repeatability Long term stability of offset and span4 Response time (10 to 90 %) Input impedance Output impedance Common mode voltage8 3 1 Min. -1.5 -2.0 -1.0 48 98 Typ. 0 0 0 50 100 ±0.1 ±0.015 Max. +1.5 -2.0 -1.0 52 102 ±0.25 ±0.030 ±2.0 ±2.0 Units mV 3 psi and 5 psi devices all others 3 psi and 5 psi devices Offset Span Offset Span ±0.5 ±0.5 ±0.1 ±0.010 ±0.1 0.1 8.0 3.0 0.5 25 4.5 1.3 ±1.0 ±1.0 ±0.3 ±0.030 ±0.3 %FSO ms 50 6.0 2.0 kΩ V Specification notes: 1. Span is the algebraic difference between the output voltage at full scale pressure and the output at zero pressure. Full scale span is ratiometric to the supply voltage. 2. Linearity is based on Best fit Straight Line from the zero to the full scale pressure. Hysteresis is the maximum output difference at any point within the operating pressure range for increasing and decreasing pressure. 3. Maximum error band of the offset voltage or span over the compensated temperature range, relative to the 25°C reading. 4. Long term stability over a six month period. 5. Response time for a step change from the zero pressure to the full scale pressure . 6. The maximum pressure that can be applied without changing the transducer´s performance or accuracy. 7. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer case. 8. Common mode voltage as measured from output to ground. 9. Absolute devices with improved zero pressure offset values are available on request. Please contact your nearest Sensortechnics sales office for further information. E / 11714 / A 3/6 www.sensortechnics.com RTO Series Stainless steel pressure sensors PHYSICAL DIMENSIONS .575 (14.61) .420 (10.67) .325 (8.26) RTO...1 (cell package) 2.0 NOMEX INSULATED RIBBON CABLE W/ .100 (2.54) PIN SPACING (24 AWG EQUIV.) Ø .746 (18.95) Ø .668 (16.98) CKT CAVITY 4 x .125 (3.2) Ø .594 (15.09) RING I.D. Ø .736 (18.69) Ø .650 (16.51) WELD RELIEF O-RING GROOVE GROOVE FOR AS568-016 O-RING (15.6 x 1.78) mass: 20 g Do not touch the diaphragm! third angle projection dimensions in inches (mm) Note: Non-concentricity effects at the diaphragm weld area may cause run out of up to ±0.006“ between the upper and lower portions of the sensor body (it is recommended to use a counter bore in the mating bore used with this device to allow for this non-concentricity). RTO...2 (flush mount package) 2.0 NOMEX INSULATED RIBBON CABLE W/ .100 (2.54) PIN SPACING (24 AWG EQUIV.) Ø .746 (18.95) 4 x .125 (3.2) Ø .668 (16.98) CKT CAVITY Do not touch the diaphragm! mass: 18 g .375 (9.55) .220 (5.59) .125 (3.18) .040 (1.02) Ø .736 (18.69) WELD RELIEF Ø .650 (16.51) O-RING GROOVE GROOVE FOR AS568-016 O-RING (15.6 x 1.78) third angle projection dimensions in inches (mm) E / 11714 / A 4/6 www.sensortechnics.com RTO Series Stainless steel pressure sensors PHYSICAL DIMENSIONS (cont.) RTO...7 (1/4 BSP package) 2.0 NOMEX INSULATED RIBBON CABLE W/ .100 (2.54) PIN SPACING (24 AWG EQUIV.) Ø .746 (18.95) Ø .668 (16.98) CKT CAVITY 4 x .125 (3.2) 1.24 (31.50) .722 (18.34) .472 (12.0) .412 (10.46) .34 (8.64) .75 (19) HEX Ø .438 Ø .720 (11.13) (18.89) Ø .171 (4.34) third angle projection mass: 52 g dimensions in inches (mm) E / 11714 / A 5/6 www.sensortechnics.com RTO Series Stainless steel pressure sensors ORDERING INFORMATION Series Options R TO Pressure range P 003 P 005 P 010 P 015 P015(V) P 030 P030(V) P 050 P 100 P100(V) P 200 P 300 P 500 0...3 psi 0...5 psi 0...10 psi 0...15 psi -15...+15 psi 0...30 psi -15...+30 psi 0...50 psi 0...100 psi -15...+100 psi 0...200 psi 0...300 psi 0...500 psi * from 15 psi upwards only ** for 15, 30 and 100 psi only Pressure mode A* G V** Absolute Gage Vacuum/gage 1 2 7 Housing style Cell Flush mount 1/4 BSP Example: R TO P 015 A 2 Note: Current supply versions are available on request. Please contact your nearest Sensortechnics sales office for further information. Sensortechnics PRO services: · Extended guarantee period of 2 years · Improved performance characteristics · Custom product modifications and adaptations even for small quantities · Advanced logistics models for supply inventory and short delivery times · Technical support through application engineers on the phone or at your site · Fastest possible technical response for design and QA engineers ... plus other services on request Sensortechnics reserves the right to make changes to any products herein. Sensortechnics does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. E / 11714 / A 6/6 www.sensortechnics.com