HR330

RED HIGH FLUX LED HR330 Technical Datasheet This revolutionary package design allows the lighting designer to reduce the number of LEDs required and provide a more uniform and unique illuminated appearance than with other LED solutions. This package LEDs are designed for high current operation and high flux output application. But the package’s design features better thermal management characteristics than other LED solutions. Because of these advantages, this product have many applications. Such as automotive tail, stop and turn signal lamps, and electronic signs etc. Application • Automotive exterior lighting • Electronic signs and signals • Channel letter / lighting • Decorative lighting • Specialty Lighting Features • High flux output and high luminance • Designed for high current operation • Uniform color • Low profile and low thermal resistance • Packaged in tubes for use with automatic insertion equipment -1- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00) RED HIGH FLUX LED Outline Dimensions HR330 Unit : mm CHAMFER 1.25 X 1.25 CATHODE 7.62 ± 0.5 ANODE 7.62 ± 0.5 5.0° 3 ± 0.2 1.4 4.4 2.5 ± 0.5 1.4 MAX 0.4 ± 0.2 1.5±0.2 0.5 0.76 ± 0.1 5.08 ± 0.2 5.08 ± 0.3 Notes : Protruded epoxy is 1.4mm maximum. -2- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00) 7.5 ± 0.5 RED HIGH FLUX LED Electro-Optical Characteristics ( Ta = 25ºC, IF=70mA ) Item Luminous Flux [1] Dominant Wavelength[3] Forward Voltage[4] View Angle Optical Efficiency Reverse Current (at VR = 5V) Symbol ФV[2] Value Min. 4.4 615 Typ. 6.0 625 2.5 90 30 5 Max. 635 3.4 HR330 Unit lm nm V deg. lm/W λd VF 2θ ½ ŋopt IR µA Absolute Maximum Ratings ( Ta = 25ºC ) Item DC Forward Current Forward Peak Pulse Current Reverse Voltage Power Dissipation Operating Temperature Storage Temperature Solder Temperature Symbol IF IFP [5] VR PD Topr Tstg TS Value 70 100 5 210 -40 ~ 100 -50 ~ 105 260ºC for 5second [6] Unit mA mA V mW ºC ºC ºC Notes : [1] SSC maintains a tolerance of ±10% on flux and power measurements. [2] ФV is the total luminous flux output as measured with an integrated sphere. [3] Dominant wavelength is derived from the CIE 1931 Chromaticity diagram. A tolerance of ±0.5nm for dominant wavelength [4] A tolerance of ±0.05V on forward voltage measurements [5] t ≤ 0.1ms, D = 1/10 [6] No closer than 1.5mm from the base of the stopper. -3- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00) RED HIGH FLUX LED Characteristic Diagrams Ta= 25ºC 100 HR330 1.6 Ta= 25ºC Relative Luminous Flux 1.6 2.0 2.4 2.8 Forward Current(mA) 1.2 10 0.8 0.4 1 0.0 0 20 40 60 80 100 Forward Voltage [V] Forward Current [mA] Forward Voltage vs. Forward Current Forward Current vs. Relative Flux 100 Ta= 25ºC 1.0 Ta= 25ºC, IF= 70mA Relative Luminous Intensity Forward Current IF [mA] 80 0.8 60 0.6 40 0.4 20 0.2 0 -40 -20 0 20 40 60 O 80 100 0.0 -90 -60 -30 0 30 60 90 Ambient Temperature TA [ C] Off Axis Angle [deg.] Ambient Temperature vs. Forward Current Directivity -4- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00) RED HIGH FLUX LED Bin Code Description Bin Code Luminous Flux J Dominant Wavelength 1 Forward Voltage 4 HR330 Luminous Flux (lm) @ IF = 70mA Bin Code A B C D E F G H J K L Min. 0.5 0.7 1.0 1.4 2.0 2.6 3.4 4.4 5.8 7.6 10.0 Max. 0.7 1.0 1.4 2.0 2.6 3.4 4.4 5.8 7.6 10.0 13.0 Dominant Wavelength (nm) @ IF = 70mA Bin Code 1 2 Min. 615 625 Max. 625 635 Forward Voltage (V) @ IF = 70mA Bin Code 1 2 3 4 5 6 7 8 9 Min. 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 Max. 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 Available ranks -5- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00) RED HIGH FLUX LED Packing 9.72 5.1 3.2 HR330 Unit : mm 0.6 2.6 5.8 13 485±1 SEOUL SEMICONDUCTOR CO., LTD. HXXXX 60pcs BINOOO * Plastic tube 60pcs max/tube HXXXX 1800pcs max/pack (30tubes max/pack) * Aluminum Sealing pack (in silica gel) RANK : XXXX QTY : 1800pcs LOT : 20XX.XX.XX SEOUL SEMICONDUCTOR CO., LTD 21600pcs/box (12packs/box) * Cardboard box (500x220x280) (21600pcs max/box) (12packs max/box) -6- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00) RED HIGH FLUX LED Soldering Profile 1) Wave Soldering Conditions / Profile • Preliminary heating to be at 85ºC(120 ºC max) for 20 seconds(60 seconds max). • Soldering heat to be at 235 ºC (240ºC max) for 4 seconds (5 seconds max.) • Soak time above 200 ºC is 5 seconds 250 HR330 PEAK 200 4s (5s max) 235 ºC (240 ºC max) Temperature [ C] 150 O 100 PREHEAT 20s (60s Max) 85 ºC(120 ºC max) 50 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 T im e [s ] 2) Hand Soldering conditions • Not more than 3 seconds at max. 350ºC, under Soldering iron. 3) Caution • Leadframes are silver plated copper alloy. This substance has a low thermal coefficient (easily conducts heat) • No closer than 1.5mm from the base of the stopper. • The LEDs must not be repositioned after soldering. • Do not apply any stress to the lead particularly when heat. Note : In case the soldered products are reused in soldering process, we don’t guarantee the products. -7- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00) RED HIGH FLUX LED Precaution for Use 1) Storage • Before opening the package HR330 Avoid the absorption of moisture, we recommended to store High Flux LEDs in a dry box(or desiccator) with a desiccant . Otherwise, store them in the following environment: Temperature : 5℃~30℃ Humidity : 50% max. • After opening the package a. Soldering should be done right after opening the package(within 24Hrs). b. Keeping of a fraction - Sealing - Temperature : 5 ~ 40℃, Humidity : less than 30% c. If the package has been opened more than 1week or the color of desiccant changes, Components should be dried for 10-12hr at 60±5℃ • Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temp. after soldering. • Avoid quick cooling • Leadframes are silver plated copper alloy. The silver plate surface may be affected by environments which contains corrosive substances. Please avoid conditions which may cause the LEDs to corrode, tarnish or discolor. 2) Static Electricity • Static Electricity and surge voltage damage the LEDs. So it is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. • All devices, equipment and machinery must be properly grounded. It is recommended precautions be taken against surge voltage to the equipment that mounts the LEDs. 3) Heat Generation • Thermal is one of the important parameter to design the end product. Please consider the heat generation of the LEDs. • The operating current should be decided after considering the ambient maximum temperature of LEDs. -8- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00) RED HIGH FLUX LED 4) Others • The color of the LEDs is changed a little by an operating current and thermal. • Anti radioactive ray design is not considered for the products listed here in. HR330 • Gallium arsenide is used in some of the products listed in this publication. These products are dangerous if they are burned or smashed in the process of disposal. It is also dangerous to drink the liquid or inhale the gas generated by such products when chemically disposed. • This device should not be used in any type of fluid such as water, oil, organic solvent and etc. When washing is required, IPA(Isopropyl Alcohol) should be used. • When the LEDs are illuminating, operating current should be decided after considering the junction temperature. Cf.) Please refer Ambient temperature vs. Forward Current graph on page 5 • The appearance and specifications of the product may be modified for improvement without notice. SEOUL SEMICONDUCTOR CO., LTD. 148-29, Kasan-Dong, Keumchun-Gu, Seoul, Korea TEL : +82-2-3281-6269 FAX :+82-2-858-5537 Homepage : www.seoulsemicon.com www.zled.com E-Store : www.zledstore.com E-mail : sscsale@seoulsemicon.com -9- Rev.1.5 서식번호 : QP-7-03-05 (Rev.00)