WH2001

Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet Specification WH2001 Preliminary SSC Drawn Approval CUSTOMER Approval Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 1. 2. 3. 4. 5. 6. 7. 8. 9. Packing Soldering CONTENTS Absolute Maximum Ratings Electro Characteristics Outline Dimension Electro-Optical characteristic Diagram Color & Binning Rank of WH603R Reliability tests 10. Precaution for use Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet - WH2001 Description 사진 Vary Thin PKG of Reflector type Surface-mounted chip LED device. Pb-free and RoHS complaint component. High brightness Low Thermal Resistance Tape and Reel packing. • • • • WH2001 Features 3.5 X 2.8 X 0.6 mm Emitted Color : White CIE chromaticity x : 0.3 y : 0.3 Material : InGaN Applications • • Electric appliance Other decoration lighting Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 1. Absolute maximum ratings Parameter Power Dissipation Forward Current Peak Forward Current Reverse Voltage Operation Temperature Storage Temperature Symbol Pd IF IFM *1 VR Topr. Tstg. Value 100 30 90 5 -30 ~ 85 -40 ~ 100 (Ta=25℃) Unit mW mA mA V ℃ ℃ *1 IFM conditions: Pulse width Tw≤0.1ms and Duty ratio≤1/10. 2. Electro-Optical Characteristics Parameter Forward Voltage Reverse Current Luminous Intensity*2 Luminous Flux Symbol VF IR IV Φ x Chromaticity Coordinates*3 y Viewing Angle*4 2θ1/2 Condition IF=20 ㎃ VR=5V IF=20 ㎃ IF=20 ㎃ IF=20 ㎃ IF=20 ㎃ IF=20 ㎃ Min 2.7 0.28 0.25 Typ 3.2 1800 5 0.3 0.3 120 Max 4.0 10 2600 0.34 0.34 - (Ta=25℃) Unit V ㎂ mcd lm ˚ *2 The luminous intensity IV is measured at the peak of the spatial pattern which may not be aligned with the mechanical axis of the LED package. *3 The CIE standard colorimetric system *4 θ1/2 is the off-axis where the luminous intensity is 1/2 the peak intensity. [Note] All products confirm to the listed minimum and maximum specifications for electric and optical characteristics, when operated at Rev. 20mA within the maximum ratings shown above. All measurements were made under the standardized environment of SSC. (Tolerance : Iv ±10%, color coordinate ±0.01, VF ±0.1V) 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 3.Outline Dimension [TOP VIEW] [SIDE VIEW] [BOTTOM VIEW] [INNER CIRCUIT] ( Tolerance: ±0.1, Unit: mm ) - Recommended Soldering Design Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Forward Current, IF [mA] Relative Intensity Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 4. Electro-Optical characteristic Diagram Forward Current vs. Forward Voltage (Ta=25 OC ) 100 10 1 2.6 2.8 3.0 3.2 3.4 3.6 3.8 Forward Voltage, VF [V] Relative Luminous Intensity vs Forward Current (Ta=25 OC ) 2.5 2.0 1.5 1.0 0.5 0.0 0 10 20 30 40 50 Forward Current[mA] Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Forward current IF(mA) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 4. Electro-Optical characteristic Diagram Ambient Temperature vs. Allowable Forward Current 25 20 15 10 5 0 -25 0 25 50 75 100 Ambient temperature Ta(? ) Radiation Diagram (Ta=25 OC ) 90 1.0 120 60 0.5 150 30 0.0 180 Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Relative Luminous Intensity (a.u.) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 4. Electro-Optical characteristic Diagram Spectrum (TA=25℃, IF=20mA) 1.0 0.8 0.6 0.4 0.2 0.0 350 400 450 500 550 600 650 700 750 800 Wavelength (nm) Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) CIE (y) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 5. Color & Binning 0.9 520 0.8 0.7 540 560 0.6 500 0.5 0.4 0.3 0.2 0.1 0.0 0.0 480 580 600 620 640 460 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 CIE (x) Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) y coordinate Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet A D 5. Color & Binning 0.34 F 0.32 E C 0.30 D B 0.28 A 0.26 0.26 0.28 0.30 0.32 0.34 x coordinate ※ Color Rank Bin CIE x 0.2966 0.2851 0.2983 0.3095 0.3095 0.2983 0.3123 0.3254 CIE y 0.2583 0.2639 0.2881 0.2811 0.2811 0.2881 0.3135 0.3079 Bin CIE x 0.2851 CIE y 0.2639 0.2700 0.2951 0.2881 0.3079 0.3300 0.3357 0.3135 Bin CIE x 0.2983 CIE y 0.2881 0.2951 0.3184 0.3135 0.3357 0.3135 0.3184 0.3400 B 0.2726 0.2875 0.2983 0.3254 C 0.2875 0.3011 0.3123 0.3257 E 0.3381 0.3257 0.3123 F 0.3123 0.3011 0.3142 Rev. 00 September 2008 * Measurement Uncertainty of the Color Coordinates : ± 0.01 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 6. Rank of WH2001 (1) Luminous Intensity: Iv [mcd] Rank A B Iv [mcd] 1000 ~ 1550 1550 ~ 2600 Condition IF =20mA (2) Color Coordinate: x, y Rank A x y x y x y x y x y x y 1 0.2966 0.2583 0.2851 0.2639 0.2983 0.2881 0.3095 0.2811 0.3254 0.3079 0.3257 0.3357 2 0.2851 0.2639 0.2726 0.2700 0.2875 0.2951 0.2983 0.2881 0.3381 0.3300 0.3123 0.3135 3 0.2983 0.2881 0.2875 0.2951 0.3011 0.3184 0.3123 0.3135 0.3257 0.3357 0.3011 0.3184 4 0.3095 0.2811 0.2983 0.2881 0.3123 0.3135 0.3254 0.3079 0.3123 0.3135 0.3142 0.3400 Condition B C IF =20mA D E F (3) Forward voltage: VF VF [V] 2.8 ~ 3.8 Condition IF =20mA Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 7. Reliability Tests Item Life Test High Temperature Operating Low Temperature Operating Thermal Shock Resistance to soldering Heat ESD (Human Body Model) High Temperature Storage Low Temperature Storage Temperature Humidity Storage Temperature Humidity Operating Condition Ta = RT, IF = 20mA Ta = 85ºC, IF = 20mA Ta = -30ºC, IF = 20mA Ta = -30ºC (30min) ~ 85ºC (30min) (Transfer time : 10sec, 1Cycle = 1hr) Ts = 255 ± 5ºC, t = 10sec 1kV, 1.5kΩ ; 100pF Ta = 100ºC Ta = -40ºC Ta = 85ºC, RH = 85% Ta = 85ºC, RH = 85%, IF = 20mA Note 1000hrs 1000hrs 1000hrs 100 cycles 1 time 1 time 1000hrs 1000hrs 1000hrs 100hrs Failures 0/22 0/22 0/22 0/40 0/22 0/22 0/22 0/22 0/22 0/22 < Judging Criteria For Reliability Tests > VF IR ФV Notes : [1] USL : Upper Standard Level [2] LSL : Lower Standard Level. USL[1] X 1.2 USL X 2.0 LSL [2] X 0.7 Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) 3.7±0.1 (2.75) 22 13 ±0.2 Label Tolerance: ±0.2, Unit: ㎜ (1) Quantity: 2,000pcs./Reel (2) Cumulative Tolerance: Cumulative Tolerance/10pitches to be ±0.2mm (3) Adhesion Strength of Cover Tape: Adhesion strength to be 0.1-0.7N when the over tape is turned off from the carrier tape at10˚angle to be the carrier tape. (4) Package: P/N, Manufacturing data Code No. and quantity to be indicated on a damp proof Package. Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) 60 +0.2 -0 Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 8. Packing 4.0±0.1 1.5 +0.1 -0 2.9±0.1 1.75±0.1 3.5±0.05 8.0±0.1 0.25±0.05 Marking Direction 0.85±0.1 180 +0 -3 11.4 9 ±0.3 2 ±0.2 Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet ● Reel Packing Structure Reel Product No.: SSC-WH2001 Quantity : 2000 Batch/Lot number :############ Aluminum Vinyl Bag Product No.: SSC-WH2001 Quantity : 2000 Batch/Lot number : ############ Outer Box *Material: Paper(SW3B(B)) a 7inch 245 c TUV MADE IN KOREA TYPE SIZE(mm) b 220 c 142 Acriche RoHS CHIP LED PART : SSCWh2001 CODE : Q'YT : 20,000EA LOT NO : DATE : SEOUL SEMICONDUCTOR CO.,LTD Semiconductor EcoLight b a Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 9. Soldering (1) Lead Solder Lead Solder Lead Solder Pre-heat Pre-heat time Peak-Temperature Soldering time Condition 120~150℃ 120 sec. Max. 240℃ Max. 2.5~5 C / sec. 2.5~5 o C / sec. Pre-heating 120~150 oC 240 oC Max. 10 sec. Max. 60sec. Max. Above 200 oC 120sec. Max. 10 sec. Max. (2) Lead-Free Solder L ea d -fra m e Solder Lead Free Solder Pre-heat Pre-heat time Peak-Temperature Soldering time Condition 150~200℃ 120 sec. Max. 260℃ Max. 1~5 o C / sec. 1~5 o C / sec. Pre-heating 150~200 o C 26 0 oC M ax. 10 sec. M ax. 60sec. M a x. A b o ve 220 oC 120sec. M ax. 10 sec. Max. (3) Hand Soldering conditions Do not exceed 3 seconds at maximum 280ºC under soldering iron. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter, the picking up nozzle that does not affect the silicone resign should be used. Note : In case that the soldered products are reused in soldering process, we don’t guarantee the products. Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet 10. Precaution for use (1) Storage In order to avoid the absorption of moisture, it is recommended to store in the dry box (or desiccator) with a desiccant. Otherwise, to store them in the following environment is recommended. Temperature : 5℃~30℃ Humidity : 60%HR max. (2) Attention after opened However LED is corresponded SMD, when LED be soldered dip, interfacial separation may affect the light transmission efficiency, causing the light intensity to drop. Attention in followed. a. After opened and mounted, the soldering shall be quickly. b. Keeping of a fraction Temperature : 5 ~ 40℃ Humidity : less than 30% (3) In case of more than 1 week passed after opening or change color of indicator on desiccant components shall be dried 10-12hr. at 60±5℃. (4) In case of supposed the components is humid, shall be dried dip-solder just before. 100Hr at 80±5℃ or 12Hr at 100±5℃. (5) Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temp. after soldering. (6) Quick cooling shall not be avoid. (7) Components shall not be mounted on warped direction of PCB. (8) Anti radioactive ray design is not considered for the products listed here in. (9) Gallium arsenide is used in some of the products listed in this publication. These products are dangerous if they are burned or smashed in the process of disposal. It is also dangerous to drink the liquid or inhale the gas generated by such products when chemically disposed. (10) This device should not be used in any type of fluid such as water, oil, organic solvent and etc. When washing is required, IPA should be used. (11) When the LEDs are illuminating, operating current should be decided after considering the ambient maximum temperature. (12) LEDs must be stored to maintain a clean atmosphere. If the LEDs are stored for 3 months or more after being shipped from SSC, a sealed container with a nitrogen atmosphere should be used for storage. (13) The LEDs must be soldered within seven days after opening the moisture-proof packing. (14) Repack unused products with anti-moisture packing, fold to close any opening and then store in a dry place. (15) The appearance and specifications of the product may be modified for improvement without notice. Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00)