SGM8584XS14G/TR

SGM8584 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier PRODUCT DESCRIPTION FEATURES The SGM8584 is a quad rail-to-rail input and output • Low Offset Voltage: 25µV (TYP) precision operational amplifier which has low input offset • Rail-to-Rail Input and Output Swing voltage, and bias current. It is guaranteed to operate • 2.5V to 5.5V Single Supply Operation from 2.5V to 5.5V single supply. • Voltage Gain: 135dB (TYP) at +5V • PSRR: 115dB (TYP) The rail-to-rail input and output swings provided by the • CMRR: 92dB (TYP) SGM8584 make both high-side and low-side sensing • Low Input Bias Current: 60pA easy. The combination of characteristics makes the • Low Supply Current: 430µA/Channel SGM8584 good choices for temperature, position and • Overload Recovery Time: 30µs (at VS = +5V) pressure sensors, medical equipment and strain gauge • No External Capacitors Required amplifiers, or any other 2.5V to 5.5V application requiring • -40℃ to +125℃ Operating Temperature Range precision and long term stability. • Available in Green SOIC-14 and TSSOP-14 Packages The SGM8584 is specified for the extended industrial/ automotive (-40℃ to +125℃) temperature range. The SGM8584 comes in the Green SOIC-14 and TSSOP-14 PIN CONFIGURATIONS (Top View) packages. SGM8584 APPLICATIONS Temperature Measurements Pressure Sensors Precision Current Sensing Electronic Scales Strain Gage Amplifiers Medical Instrumentation Thermocouple Amplifiers Handheld Test Equipment OUTA 1 14 OUTD -INA 2 13 -IND +INA 3 12 +IND +VS 4 11 -VS +INB 5 10 +INC -INB 6 9 -INC OUTB 7 8 OUTC SOIC-14/TSSOP-14 SG Micro Limited www.sg-micro.com REV. A. 2 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 PACKAGE/ORDERING INFORMATION MODEL ORDER NUMBER SGM8584 PACKAGE DESCRIPTION PACKAGE OPTION MARKING INFORMATION SGM8584XS14G/TR SOIC-14 Tape and Reel, 2500 SGM8584XS14 SGM8584XTS14G/TR TSSOP-14 Tape and Reel, 3000 SGM8584XTS14 ABSOLUTE MAXIMUM RATINGS CAUTION Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . -VS to (+VS) + 0.1V Differential Input Voltage. . . . . . . . . . . . . . . . . . . . . . -5V to 5V Storage Temperature Range . . . . . . . . . . . . . .-65℃ to +150℃ This integrated circuit can be damaged by ESD if you don’t pay attention to ESD protection. SGMICRO recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. Junction Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . .150℃ Operating Temperature Range. . . . . . . . . . . . .-40℃ to +125℃ Lead Temperature Range (Soldering 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260℃ ESD Susceptibility HBM (TSSOP-14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8000V HBM (SOIC-14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7000V MM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400V SGMICRO reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. Please contact SGMICRO sales office to get the latest datasheet. NOTE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. SG Micro Limited www.sg-micro.com 2 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 ELECTRICAL CHARACTERISTICS (VS = +5V, VCM = +2.5V, VO = +2.5V, TA = +25℃, unless otherwise noted.) PARAMETER CONDITIONS MIN TYP MAX 25 100 UNITS INPUT CHARACTERISTICS Input Offset Voltage (VOS) 110 -40℃ ≤ TA ≤ +125℃ Input Bias Current (IB) 60 Input Offset Current (IOS) Common-Mode Rejection Ratio (1) (CMRR) Large Signal Voltage Gain ( AVO) Input Offset Voltage Drift (∆VOS/∆T ) pA 50 Input Voltage Range 0 VCM = 0V to 5V 88 -40℃ ≤ TA ≤ +125℃ 77 RL = 10kΩ, VO = 0.3V to 4.7V 120 -40℃ ≤ TA ≤ +125℃ 104 pA 5 92 V dB 135 dB 150 -40℃ ≤ TA ≤ +125℃ µV nV/℃ OUTPUT CHARACTERISTICS RL = 100kΩ to -VS Output Voltage High (VOH) -40℃ ≤ TA ≤ +125℃ RL = 10kΩ to -VS -40℃ ≤ TA ≤ +125℃ 4.9 4.9 4.994 V 4.888 3.5 6 8 -40℃ ≤ TA ≤ +125℃ RL = 10kΩ to +VS 7 10 23 -40℃ ≤ TA ≤ +125℃ Short Circuit Limit (ISC) V 4.894 RL = 100kΩ to +VS Output Voltage Low (VOL) 4.998 VO = 2.5V, RL = 10Ω to GND 30 -40℃ ≤ TA ≤ +125℃ 22 VS = 2.5V to 5.5V 90 -40℃ ≤ TA ≤ +125℃ 80 40 mV mV mA POWER SUPPLY Power Supply Rejection Ratio (1) (PSRR) Quiescent Current / per Channel (IQ) VO = +VS/2 115 430 dB 555 710 -40℃ ≤ TA ≤ +125℃ μA DYNAMIC PERFORMANCE Gain-Bandwidth Product (GBP) AV = +100 1.5 MHz Slew Rate (SR) AV = +1, RL = 10kΩ, 2V Output Step 0.9 V/μs Overload Recovery Time AV = -100, RL = 10kΩ, VIN = 200mV (RET to GND) 0.03 ms 0.1Hz to 10Hz 1.4 μVP-P 78 nV/ Hz NOISE PERFORMANCE Voltage Noise (en p-p) Voltage Noise Density (en) f = 1kHz NOTE 1: PSRR and CMRR are affected by the matching between external gain-setting resistor ratios. SG Micro Limited www.sg-micro.com 3 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 ELECTRICAL CHARACTERISTICS (VS = +2.5V, VCM = +1.25V, VO = +1.25V, TA = +25℃, unless otherwise noted.) PARAMETER CONDITIONS MIN TYP MAX 25 100 UNITS INPUT CHARACTERISTICS Input Offset Voltage (VOS) 120 -40℃ ≤ TA ≤ +125℃ Input Bias Current (IB) 30 Input Offset Current (IOS) Common-Mode Rejection Ratio (1) (CMRR) Large Signal Voltage Gain ( AVO) Input Offset Voltage Drift (∆VOS/∆T ) pA 20 Input Voltage Range 0 VCM = 0V to 2.5V 79 -40℃ ≤ TA ≤ +125℃ 70 RL = 10kΩ, VO = 0.3V to 2.4V 120 -40℃ ≤ TA ≤ +125℃ 104 pA 2.5 85 V dB 130 dB 150 -40℃ ≤ TA ≤ +125℃ µV nV/℃ OUTPUT CHARACTERISTICS Output Voltage High (VOH) RL = 100kΩ to -VS 2.4 -40℃ ≤ TA ≤ +125℃ 2.38 RL = 10kΩ to -VS -40℃ ≤ TA ≤ +125℃ 2.4 2.497 4 V 6 7 -40℃ ≤ TA ≤ +125℃ RL = 10kΩ to +VS 6 8 12 -40℃ ≤ TA ≤ +125℃ Short Circuit Limit (ISC) V 2.389 RL = 100kΩ to +VS Output Voltage Low (VOL) 2.499 VO = 1.25V, RL = 10Ω to GND 20 -40℃ ≤ TA ≤ +125℃ 13 VS = 2.5V to 5.5V 90 -40℃ ≤ TA ≤ +125℃ 80 28 mV mV mA POWER SUPPLY Power Supply Rejection Ratio (1) (PSRR) Quiescent Current / per Channel (IQ) VO = +VS/2 115 430 dB 550 710 -40℃ ≤ TA ≤ +125℃ μA DYNAMIC PERFORMANCE Gain-Bandwidth Product (GBP) AV = +100 1.5 MHz Slew Rate (SR) AV = +1, RL = 10kΩ, 2V Output Step 1.0 V/μs Overload Recovery Time AV = -100, RL = 10kΩ, VIN = 200mV (RET to GND) 0.02 ms 0.1Hz to 10Hz 1.7 μVP-P 108 nV/ Hz NOISE PERFORMANCE Voltage Noise (en p-p) Voltage Noise Density (en) f = 1kHz NOTE 1: PSRR and CMRR are affected by the matching between external gain-setting resistor ratios. SG Micro Limited www.sg-micro.com 4 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 TYPICAL PERFORMANCE CHARACTERISTICS Large Signal Transient Response at +2.5V VOUT (500mV/div) VOUT (1V/div) Large Signal Transient Response at +5V CL = 300pF RL = 2kΩ AV = +1 CL = 300pF RL = 2kΩ AV = +1 Time (5µs/div) Time (2µs/div) Small Signal Transient Response at +2.5V Small Signal Transient Response at +5V CL = 50pF RL = ∞ AV = +1 VOUT (50mV/div) VOUT (50mV/div) CL = 50pF RL = ∞ AV = +1 Time (5µs/div) Time (5µs/div) Closed Loop Gain vs. Frequency at +5V Closed Loop Gain vs. Frequency at +2.5V 60 60 50 AV = -100 40 Closed Loop Gain (dB) Closed Loop Gain (dB) 50 30 20 10 0 AV = -10 -10 AV = +1 -20 -30 -40 AV = -100 40 30 20 10 AV = -10 0 -10 AV = +1 -20 -30 -40 10 100 1000 Frequency (kHz) SG Micro Limited www.sg-micro.com 10000 10 100 1000 10000 Frequency (kHz) 5 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 TYPICAL PERFORMANCE CHARACTERISTICS 0.1Hz to 10Hz Noise at +5V Noise (2mV/div) Noise (2mV/div) 0.1Hz to 10Hz Noise at +2.5V AV = +10,000 AV = +10,000 Time (5s/div) Time (5s/div) Negative Overvoltage Recovery Positive Overvoltage Recovery VIN 200mV /div VSY = ±2.5V VIN = +200mVP-P (RET to GND) CL = 0pF RL = 10kΩ AV = -100 0V VOUT 1V /div VOUT VSY = ±2.5V VIN = -200mVP-P (RET to GND) CL = 0pF RL = 10kΩ AV = -100 1V /div 0V Time (20µs/div) Time (20µs/div) Open Loop Gain, Phase Shift vs. Frequency at +2.5V Open Loop Gain, Phase Shift vs. Frequency at +5V CL = 0pF RL = ∞ Phase Shift 40 120 60 96 50 40 30 72 20 10 48 0 Open Loop Gain -20 24 Open Loop Gain (dB) Open Loop Gain (dB) 50 Phase Shift (Degrees) 60 -10 200mV /div 120 CL = 0pF RL = ∞ Phase Shift 96 30 20 72 10 0 -10 48 Open Loop Gain -20 24 Phase Shift (Degrees) 0V 0V VIN -30 -30 -40 10 100 1000 10000 Frequency (kHz) SG Micro Limited www.sg-micro.com 0 100000 -40 10 100 1000 10000 0 100000 Frequency (kHz) 6 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 TYPICAL PERFORMANCE CHARACTERISTICS Voltage Noise Density at +2.5V from 0.1Hz to 2.5kHz 100 100 90 80 70 60 50 40 30 20 10 0 90 RS = 0Ω RS = 0Ω 80 en (nV/√Hz) en (nV/√Hz) Voltage Noise Density at +5V from 0.1Hz to 2.5kHz 70 60 50 40 30 20 10 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 0 2 0 Frequency (kHz) 128 128 112 112 96 96 en (nV/√Hz) en (nV/√Hz) 2 Voltage Noise Density at +2.5V from 0.1Hz to 25kHz Voltage Noise Density at +5V from 0.1Hz to 25kHz 80 64 48 80 64 48 32 32 16 RS = 0Ω 16 RS = 0Ω 0 0 0 5 10 15 Frequency (kHz) 20 25 0 5 20 25 120 100 100 PSRR (dB) -PSRR 60 +PSRR 40 15 PSRR vs. Frequency at ±1.25V PSRR vs. Frequency at ±2.5V 80 10 Frequency (kHz) 120 PSRR (dB) 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 Frequency (kHz) +PSRR 80 60 -PSRR 40 20 20 0 0 0.1 1 10 100 Frequency (kHz) SG Micro Limited www.sg-micro.com 1000 10000 0.1 1 10 100 Frequency (kHz) 1000 10000 7 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 TYPICAL PERFORMANCE CHARACTERISTICS CMRR vs. Frequency at +2.5V 100 80 80 CMRR (dB) 60 40 60 40 20 20 0 0 0.1 1 10 100 Frequency (kHz) 1000 0.1 10000 Percent of Amplifiers (%) TA = +25℃ 10 100 Frequency (kHz) 1000 10000 50 45 40 35 30 25 VS = +2.5V VCM = 1.25V TA = +25℃ 20 15 10 5 Offset Voltage (µV) SG Micro Limited www.sg-micro.com 100 80 60 40 20 0 -20 100 80 60 40 20 0 -20 0 -40 Percent of Amplifiers (%) VS = +5V VCM = 2.5V 1 Offset Voltage Production Distribution at +2.5V Offset Voltage Production Distribution at +5V 50 45 40 35 30 25 20 15 10 5 0 -40 CMRR (dB) CMRR vs. Frequency at +5V 100 Offset Voltage (µV) 8 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 PACKAGE OUTLINE DIMENSIONS SOIC-14 D INDEX Ф0.8±0.1 DEP 0.2±0.1 E 5.2 E1 Ф2.0±0.1 BTM E-MARK DEP 0.1±0.05 2.2 e b 0.6 1.27 RECOMMENDED LAND PATTERN (Unit: mm) L1 A A2 Dimensions In Millimeters MIN MOD L2 θ A1 Symbol h L R1 R A3 h Dimensions In Inches MAX MIN MOD MAX A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.004 0.010 A2 1.25 1.65 0.049 0.065 A3 0.55 0.75 0.022 0.030 b 0.36 0.49 0.014 0.019 D 8.53 8.73 0.336 0.344 E 5.80 6.20 0.228 0.244 E1 3.80 4.00 0.150 e L 1.27 BSC 0.45 0.157 0.050 BSC 0.80 0.018 0.032 L1 1.04 REF 0.040 REF L2 0.25 BSC 0.01 BSC R 0.07 0.003 R1 0.07 0.003 h 0.30 0.50 0.012 0.020 θ 0° 8° 0° 8° SG Micro Limited www.sg-micro.com 9 Single-Supply, Quad Rail-to-Rail I/O Precision Operational Amplifier SGM8584 PACKAGE OUTLINE DIMENSIONS TSSOP-14 D E1 E 5.94 1.78 b e 0.42 0.65 RECOMMENDED LAND PATTERN (Unit: mm) L A A1 θ A2 Symbol Dimensions In Millimeters MIN MAX A A1 c H Dimensions In Inches MIN MAX 1.100 0.050 0.150 0.043 0.002 0.006 A2 0.800 1.000 0.031 0.039 b 0.190 0.300 0.007 0.012 c 0.090 0.200 0.004 0.008 D 4.900 5.100 0.193 0.201 E 4.300 4.500 0.169 0.177 E1 6.250 6.550 0.246 0.258 e L 0.650 BSC 0.500 H θ SG Micro Limited www.sg-micro.com 0.026 BSC 0.700 0.02 0.25 TYP 1° 0.028 0.01 TYP 7° 1° 7° 10