6N136

6N135/6N136 6N135/6N136 s Features 1. High speed response t PHL , t PLH ( 6N135 : MAX. 1.5 µ s at R L = 4.1k Ω ) ( 6N136 : MAX. 0.8 µ s at R L = 1.9k Ω ) 2. High common mode rejection voltage ( CM H : TYP. 1kV/ µ s ) 3. Standard dual-in-line package 4. Recognized by UL, file No. E64380 General Purpose Type Photocoupler s Outline Dimensions 0.85 ± 0.3 8 7 6N 6 Model 1.2 ± 0.3 No. 5 6.5 ± 0.5 ( Unit : mm ) Internal connection diagram 8 7 6 5 1 2 3 4 0.8 1 2 3 4 s Applications 1. Computers, measuring instruments, control equipment 2. High speed line receivers, high speed logic 3. Telephone sets 4. Signal transmission between circuits of different potentials and impedances 0.5TYP 3.5 ± 0.5 Primary side mark (Sunken place ) 9.22 ± 0.5 7.62 ± 0.3 3.7 ± 0.5 θ = 0 to 13 ˚ 0.5 ± 0.1 2.54 ± 0.25 0.26 ± 0.1 GND VO V B θ 1 2 3 NC Anode Cathode NC 5 6 7 8 s Absolute Maximum Ratings Parameter Forward current *1 Peak forward current Input *2Peak transient forward current ( Ta = 25˚C ) Rating 25 50 1 5 45 - 0.5 to + 15 - 0.5 to + 15 5 8 16 5 100 2 500 - 55 to + 100 - 55 to + 125 260 Unit mA mA A V mW V V V mA mA mA mW V rms ˚C ˚C ˚C 4 V CC Reverse voltage Power dissipation Supply voltage Output voltage Emitter-base reverse with( Pin 5 to 7 stand voltage ) Output Average output current Peak output current Base current ( Pin 7 ) Power dissipation *3 Isolation voltage Operating temperature Storage temperature *4 Soldering temperature Symbol IF IF I FM VR P V CC VO V EBO IO I OP IB PO V iso T opr T stg T so1 * “ OPIC ” ( Optical IC ) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signalprocessing circuit integrated onto a single chip. *1 50% duty cycle, Pulse width : 1ms Decreases at the rate of 1.6mA/˚C if the external temperature is 70˚C or more. *2 Pulse width 2.0V) . Instantaneous common mode rejection voltage “ output ( 0 ) ” represents a common mode voltage variation that can hold the output above ( 0 ) level ( VO < 0.8V) . *12 6N135 : RL = 4.1k Ω 6N136 : RL = 1.9k Ω *13 Bandwidth represents a point where AC input goes down by 3dB. *9 Test Circuit for Propagation Delay Time Pulse input Duty ratio = 1/10 Pulse Generator IF 1 2 3 IF monitor 100 Ω 4 8 7 6 5 0.01 µ F IF 0 VCC RL VO CL = 15pF t PHL t PLH 1.5V 1.5V VO 5V *11 Test Circuit for Instantaneous Common Mode Rejection Voltage IF 1 2 3 A B VFF + 4 VCM 8 7 6 5 0.01 µ F VCC = 5V RL VO 10V VCM 0V CMH VO CML VO 10% tr IF = 0 90% 10% 90% tf 2V 5V 0.8V IF = 16mA VOL 6N135/6N136 Fig. 1 Forward Current vs. Ambient Temperature 30 Fig. 2 Power Dissipation vs. Ambient Temperature 120 PO Power dissipation P, P O ( mW ) 25 ( mA ) 100 20 80 Forward current I F 15 60 45 40 P 10 5 0 - 55 20 0 -40 0 25 50 75 100 Ambient temperature T a ( ˚C ) 125 0 25 50 70 75 100 Ambient temperature T a ( ˚C ) 125 Fig. 3 Forward Current vs. Forward Voltage 100 Fig. 4 Relative Current Transfer Ratio vs. Forward Current 150 V CC = 5V Relative current transfer ratio ( % ) VO = 0.4V T a = 25 ˚C 100 Forward current I F ( mA ) 10 1 T a = 0˚C 25˚C 50˚C 70˚C 50 CTR = 100% at I F = 16mA 0 0.1 1 10 Forward current I F ( mA ) 100 0.1 0.01 1.0 1.2 1.4 1.6 1.8 Forward voltage V F ( V ) 2.0 2.2 Fig. 5 Output Current vs. Output Voltage 20 18 16 Output current I O ( mA ) 14 12 10 8 10mA 6 4 2 0 0 2 4 6 8 10 12 14 Output voltage V O ( V ) 16 18 20 5mA I F = 25mA 20mA V CC = 5V T a = 25 ˚C Dotted line shows pulse characteristics Fig. 6 Relative Current Transfer Ratio vs. Ambient Temperature 110 I F = 16mA VO = 0.4V V CC = 5V Relative current transfer ratio ( % ) 100 90 15mA 80 70 CTR = 100 % at T a = 25 ˚C 60 - 60 - 40 - 20 0 20 40 60 80 100 Ambient temperature T a ( ˚C ) 6N135/6N136 Fig. 7 Propagation Delay Time vs. Ambient Temperature 800 ( ns ) 6N135 (RL = 4.1k Ω ) 6N136 (RL = 1.9k Ω ) 600 t PHL I F = 16mA V CC = 5V Fig. 8 High Level Output Current vs. Ambient Temperature 10 (A) -5 V CC = VO = 5V -6 PLH 10 ,t High level output current I 80 100 PHL OH 10 -7 Propagation delay time t 400 t PLH 200 10 -8 10 -9 10 0 - 60 - 40 - 20 10 0 20 40 60 - 10 - 11 - 60 - 40 - 20 0 20 40 60 80 100 Ambient temperature T a ( ˚C ) Ambient temperature T a ( ˚C ) Fig. 9 Frequency Response 0 IF = 16mA T a = 25˚C -5 Voltage gain A V ( dB ) RL = 100Ω -10 220Ω 470Ω 1k Ω -20 560 Ω 100 Ω AC Input -25 -30 15V 1 5V 2 20k Ω 3 4 1.6V DC 0.25VP - P AC 7 6 5 RL VO 8 Test Circuit for Frequency Characteristic -15 0.1 0.2 0.5 1 2 5 10 Frequency f ( MHz ) s Precautions for Use ( 1 ) It is recommended that a by-pass capacitor of more than 0.01 µ F be added between V CC and GND near the device in order to stabilize power supply line. ( 2 ) Transistor of detector side in bipolar configuration is apt to be affected by static electricity for its minute design. When handling them, general counterplan against static electricity should be taken to avoid breakdown of devices or degradation of characteristics. q As for other general cautions, please refer to the chapter “ Precautions for Use ” . ( Page 78 to 93 )