GP1A44E1

GP1A44E1 GP1A44E1 Transmissive Type Photointerrupter with Actuator ■ Features ■ Outline Dimensions (0.5) (5.0) 18.0 17.2 1 2 3 (9.35) 11.0 8.0 6.2 4.0 15.3 (8.0) 1. With compact actuator 2. Easy wiring due to built-in connector 3. Snap-in mounting type in order to mount to an equipment easily 4. OPIC output type for direct connection to microcomputer ( Unit : mm ) 15.5 ❈ R0.5 1.5 (20 )˚ ■ Applications 1.0 0.6 0.2 1.5 12.8 10.8 Internal connection diagram Voltage regulator 1 15k Ω 2 1.0 17.0 16.8 13.8 11.4 9.9 (8.0) 6.9 5.4 2.4 0.8 1. Copiers 2. Laser beam printers 3. Facsimiles 1.5 (5.0) 1 GND 2 V OUT 3 V CC 3 Amp * Tolerance :± 0.3mm * ( ): Reference dimensions ❈ DF3A-3P-2DSA made by HIROSE Japan Co. Ltd. *“ OPIC” ( Optical IC ) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signalprocessing circuit integrated onto a single chip. ■ Absolute Maximum Ratings Parameter Supply voltage *1 Output current *2 Operating temperature *2 Storage temperature ( Ta = 25˚C ) Symbol VCC I OL Topr Tstg Rating - 0.5 to + 10 50 - 20 to + 75 - 40 to + 85 Unit V mA ˚C ˚C *1 Collector current of output transistor *2 The connector should be plugged in/out at normal temperature. “ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.” GP1A44E1 ■ Electro-optical Characteristics Parameter Low level dissipation current ( Unless otherwise specified, VCC = 5V, Ta= 25˚C ) Symbol I CCL Low level output voltage VOL High level dissipation current High level output voltage Operating supply voltage I CCH VOH VCC Conditions Light beam interrupted Light beam interrupted I OL = 16mA Light beam uninterrupted Light beam uninterrupted Ta =- 20 to + 75˚C MIN. - TYP. - MAX. 20 - - 0.4 V V CC x 0.9 4.5 - 20 5.5 mA V V * Condition of light beam interrupted : Lever is normal condition on the Fig.1. Condition of light beam uninterrupted : Lever is 30˚ or more movement condition from A point to B point on Fig.1. Fig. 1 Detecting Position Output voltage between A point and C point shall be from low level to high level when the actuator level rotated ( 37˚± 5˚ ) from normal condition B point to C point in Fig.1. Normal condition B point shall be opaque condition. Normal position C point 20˚ B point A point Fig. 2 Output Voltage vs. Actuator Lever Angle ■ Mechanical Characteristics Operation range High - Lever starting torque: 1x 10 4 N • m or loss ■ Lever Life Output voltage 100 000 times or more ( Lever reciprocating operation between normal condition B point and C point at the condition of no load. ) Low 0 32 37 42 Actuator lever angle ( ˚) Unit mA GP1A44E1 Fig. 4 Low Level Output Voltage vs. Low Level Output Current 60 1.0 50 0.5 Low level output voltage VOL ( V ) Low level output current I OL ( mA ) Fig. 3 Low Level Output Current vs. Ambient Temperature 40 - 0.67mA /˚C 30 20 10 0 - 25 VCC = 5V T a = 25˚C 0.2 0.1 0.05 0.02 0.01 - 20 0 25 50 75 100 1 2 Ambient temperature Ta ( ˚C ) 5 10 20 50 100 Low level output current I OL ( mA ) Fig. 5 Low Level Output Voltage vs. Ambient Temperature Fig. 6 Supply Current vs. Supply Voltage 0.6 30 0.5 Supply current I CC ( mA ) Low level output voltage V OL ( V ) V CC = 5V 0.4 I OL = 30mA 0.3 16mA 0.2 I CCL 10 I CCH 5mA 0.1 0 - 25 T a =- 20˚C + 25˚C + 75˚C 20 T a =- 20˚C, + 25˚C,+ 75˚C 0 0 25 50 75 100 4.5 Ambient temperature Ta ( ˚C ) 5.0 5.5 Supply voltage VCC ( V ) ● Please refer to the chapter “ Precautions for Use” ( Page 78 to 93 ) . Application Circuits NOTICE ●The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. ●Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. ●Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). ●Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. ●If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. ●This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. ●Contact and consult with a SHARP representative if there are any questions about the contents of this publication. 115