GP1F351R

GP1F351T/GP1F351R GP1F351T/GP1F351R s Features 1. Electric and optical signal compatible design ( Three kinds of terminals are ) integrated into a single unit. 2. Compact design with small jack compatible mini-plug ( Less than 1/2 in volume of GP1F32T/R ) 3. OPIC type ( Direct interface to microcomputer of the I/O signals ) ( High fidelity real sound reproduction) 4. High speed data transmission Signal transmisson speed: MAX. 8Mbps ( NRZ signal ) Optical Mini-Jack for Digital Audio Equipment s Outline Dimensions 3 - 1.5 3 - 0.5 2.54 2.54 7.2 ( Unit : mm) 10 φ 3.6 6.7 3.3 18.1 2.5 φ6 2.8 2.3 3.7 3.7 9.65 1.85 4 5 3 2 1 789 6 2 1 4.0 6.1 8 - 1.0 11.0 1 2 3 4 5 6 7 8 9 8.7 5.05 s Applications 1. MD, DCC 2. Portable CD, DAT 7.0 Jack terminal Device terminal Jack terminal configuration GP1F351T 1 4 6 2 3 5 LED Drive IC 8 Vcc 7 Vin 9 GND GP1F351R 1 4 6 2 3 5 7 Vcc 9 Vout 8 GND OPIC light detector ∗ OPIC is a trademark of Sharp and stands for Optical IC. It has light detecting element and signal processing circuitry integrated single chip. “ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device. ” GP1F351T/GP1F351R s Absolute Maximum Ratings GP1F351T/GP1F351R ( Photoelectric conversion element ) Parameter Supply voltage Output current ( GP1F351R ) Input voltage ( GP1F351T ) Operating temperature Storage temperature ∗1 Soldering temperature Symbol VCC I OH I OL Vim Topr Tstg Tsol Rating - 0.5 to + 7.0 4 ( source current) 4 ( sink current ) - 0.5 to V CC+ 5.0 - 20 to + 70 - 30 to + 80 260 Unit V mA mA V ˚C ˚C ˚C GP1F351T/GP1F351R ( Jack ) Parameter Total power dissipation Isolation voltage Operating temperature Storage temperature ∗1 Soldering temperature ∗1 5s/time up to 2 times. Symbol Ptot Viso Topr Tstg Tsol Rating D.C.12V, 1A A.C. 500V rms ( For 1min. ) - 20 to 70 - 30 to 80 260 Unit ˚C ˚C ˚C s Recommended Operating Conditions GP1F351T Parameter Supply voltage Operating transfer rate Symbol VCC T MIN. 4.75 TYP. 5.0 MAX. 5.25 8 Unit V Mbps GP1F351R Parameter Supply voltage Operating transfer rate Receiver input optical power level Symbol VCC T PC MIN. 4.75 0.1 - 24.0 TYP. 5.0 MAX. 5.25 8 - 14.5 Unit V Mbps dBm s Electro-optical Characteristics GP1F351T ( Photoelectric conversion element ) Parameter Peak emission wavelength Optical power output coupling with fiber Supply current High level input voltage Low level input voltage Low→High delay time High→Low delay time Pulse width distortion Jitter Symbol λP PC I CC V iH ViL t PLH t PHL ∆ tw ∆ tj Conditions Refer to Fig. 1 Refer to Fig. 2 Refer to Fig. 2 Refer to Fig. 2 Refer to Fig. 3 Refer to Fig. 3 Refer to Fig. 3 Refer to Fig. 3 MIN. 630 - 21 2 - 25 TYP. 660 - 17 4 1 ( Ta = 25˚C ) MAX. 690 - 15 10 0.8 100 100 + 25 25 Unit nm dBm mA V V ns ns ns ns GP1F351T/GP1F351R GP1F351R ( Photoelectric conversion element ) Parameter Peak sensitivity wavelength Supply current High level output voltage Low level output voltage Rise time Fall time Low→ High delay time High→ Low delay time Pulse width distortion PC = - 14.5dBm Jitter PC = - 24dBm Symbol λP I CC VOH VOL tr tf t PLH t PHL ∆ tw Conditions Refer to Fig. 4 Refer to Fig. 5 Refer to Fig. 5 Refer to Fig. 5 Refer to Fig. 5 Refer to Fig. 5 Refer to Fig. 5 Refer to Fig. 5 Refer to Fig. 6 MIN. 2.7 - 30 TYP. 700 15 3.5 0.2 12 4 1 - ( Ta= 25˚C) MAX. 40 0.4 30 30 100 100 + 30 30 30 Unit nm mA V V ns ns ns ns ns ns ns ∆ tj s Mechanical and Electrical Characteristics GP1F351T/GP1F351R ( Jack) Parameter Insertion force, withdrawal force Contact resistance Isolation resistance Symbol FP Rcon R ISO Conditions ∗2 ∗3 D.C. 500V, 1min. MIN. 5 100 TYP. MAX. 35 30 Unit N mΩ MΩ Note) This jack is designed for applicable to φ 3.5 compact single head plug ( EIAJ RC-6701A ) . ∗2 Measuring method of insertion force and withdrawal force. Insertion and withdrawal force shall be measured after inserting and withdrawing 3 times by using EIAJ RC-6701A standard plug for test. ∗3 Measuring method of contact resistance. About movable contact terminal and make contacts, it measures at 100mA or less and 1000HZ at the condition of inserting EIAJ 6701A standard plug for tast. Fig. 1 Measuring Method of Optical Output Coupling Fiber Standard optical fiber cable GP1F351T Unit to be measured Vin VCC GND VCC D The optical power meter must be calibrated to have the wavelength sensitivity of 660nm. ( 0dB= 1mW ) Optical power meter (Anritsu ) ML93B Note ) ( 1 ) VCC = 5.0V ± 0.05V ( State of operating ) ( 2 ) To bundle up the standard fiber optic cable, make it into a loop with the diameter D= 10cm or more. ( The standard fiber optic cable will be specified elsewhere.) GP1F351T/GP1F351R Fig. 2 Measuring Method of Input Voltage and Supply Current Standart fiber optic cable GP1F351T Unit to be measured Vin Vcc Icc Vin VCC GND D The optical power meter must be calibrated to have the wavelength sensitivity of 660nm. ( 0dB= 1mW ) Optical power meter (Anritsu ) ML93B Input conditions and judgement method Conditions Vin = 2.0V or more Vin = 0.8V or less Note ) VCC = 5.0 ± 0.05V ( State of operating) Judgement method - 21