OPTO
PHOTOCOUPLER LINEUP
■ Photocoupler Lineup
Package type
Mini-flat 4-pin
Compact, SMT type
Output type
Single phototransistor
Features
Model No. (series)
General purpose,
High collector-emitter voltage, etc.
Low input current
AC input response
Darlington phototransistor
High sensitivity,
High collector-emitter voltage
Single phototransistor
General purpose,
High resistance to noise, etc.
Low input current
Low input current
Compact, Half pitch
(lead space), SMT type
Single phototransistor
(4-pin, DIP type)
Darlington phototransistor
PC354NJ0000F
41
PC364NJ0000F
41
PC355NJ0000F / PC452J00000F
41
PC365NJ0000F
41
PC3Hx series
42
42
Low input current
PC3H71xNIP0F
42
PC3H3J00000F / PC3H4J00000F
42
Low input current
PC3H41xNIP0F
42
PC3H5J00000F
42
PC3H510NIP0F
42
Reinforced insulation
PC123XNNSZ0F
43
Low input current
General purpose,
High collector-emitter voltage, etc.
PC1231xNSZ0X
43
PC817XNNSZ0F / PC851XNNSZ0F
43
Low input current
PC8171xNSZ0X
43
High sensitivity
High sensitivity,
High collector-emitter voltage
Low input current
DIP type (6-pin)
41
41
PC3HU7xYIP0B
Low input current
DIP type (4-pin)
PC35x series / PC451J00000F
PC367NJ0000F
Reinforced insulation
AC input response
Darlington phototransistor
Page
PC815XNNSZ0F / PC852XNNSZ0F /
PC853XNNSZ0F
43
PC81510NSZ0X
43
Single phototransistor
General purpose,
High collector-emitter voltage, etc.
PC7xxV0NSZXF
44
Darlington phototransistor
High sensitivity,
High collector-emitter voltage, etc.
PC7x5V0NSZXF
44
Package type
Compact, SMT type
DIP type, SMT type
Output type
Features
Page
Digital output
General purpose, High response speed, 2ch, etc.
Analog/Digital output
High CMR
PC457S0NIP0F / PC457L0NIP0F
45
Digital output
General purpose
PC900V0NSZXF
46
For inverter control, Built-in short-circuit protection circuit
PC925LxNSZ0F / PC942J00000F ▲ /
PC928J00000F / PC929J00000F
46
Built-in base amplifier
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
40
Model No. (series)
PC400J00000F / PC456L0NIP0F ▲ /
PC410S0NIP0F / PC410L0NIP0F /
PC4D10SNIP0F
45
OPTO
PHOTOCOUPLERS
■ Photocouplers
Model No.
Internal
connection
diagram
: Approved
Approved
by safety
standards*2
Features
UL
(Ta = 25°C)
Absolute maximum ratings
Electro-optical characteristics
Current transfer ratio
Response time
Isolation
CollectorForward voltage
emitter
Package current (AC)
tr
voltage CTR
IC
IF
RL VCE
VCE
Viso
IF
(µs)
(%)
VCEO
(mA) (Ω) (V)
(mA)
(V)
(mA)
(rms)
TYP.
MIN.
(V)
(kV)
PC357NJ0000F
General purpose
❇
50
3.75
80
50
5
5
4
2
100
2
PC352NJ0000F ▲
General purpose,
high resistance to noise* 1
50
3.75
80
90
5
5
4
2
100
2
PC451J00000F
High collector-emitter
voltage
❇
50
3.75
350
40
5
5
4
2
100
2
PC367NJ0000F
Low input current,
high resistance to noise* 1
10
3.75
80
100
0.5
5
4
2
100
2
PC354NJ0000F
AC input response
❇
±50
3.75
80
20
±1
5
4
2
100
2
PC364NJ0000F
Low input current,
AC input response,
high resistance to noise* 1
±10
3.75
80
50
±0.5
5
4
2
100
2
PC355NJ0000F
High sensitivity
❇
50
3.75
35
600
1
2
60
2
100
2
PC365NJ0000F
High sensitivity,
low input current
10
3.75
35
600
0.5
2
60
10
100
2
PC452J00000F
High collector-emitter
voltage
❇
50
3.75
350
1 000
1
2
100
20
100
2
Mini-flat
4-pin
Optoelectronics
Darlington phototransistor output
Single phototransistor output
Output type
◆Phototransistor Output Type
*1 CMR: MIN.10 kV/µs
*2 Please refer to Specification Sheets for model numbers approved by safety standards.
❇ A VDE approved type is optionally available.
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
PC357NJ0000F
(Mini-flat 4-pin)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
41
OPTO
PHOTOCOUPLERS
Output type
◆Phototransistor Output Type
Darlington phototransistor output
Single phototransistor output
Model No.
*1
*2
*3
*4
*5
*6
Internal
connection
diagram
Features
UL
PC3HU7xYIP0B
Reinforced insulation
(internal insulation distance:
MIN. 0.4 mm),
low-profile package
PC3H7J00000F
Standard
PC3H71xNIP0F
*4, 5
(Ta = 25°C)
Absolute maximum ratings
Electro-optical characteristics
Current transfer
Isolation
CollectorResponse time
ratio
Forward voltage
emitter
Package current (AC)
voltage CTR
tr
Viso
IF
IC RL VCE
IF
VCE
VCEO
(µs)
(%)
(mA)
(rms)
(mA) (Ω) (V)
(mA)
(V)
(V)
TYP.
MIN.
(kV)
Lowprofile
50
3.75
80
50
5
5
4
2 100 2
mini-flat
4-pin
*6
50
2.5
80
20
1
5
4
2
100
2
High resistance to noise* 1,
low input current
10
2.5
80
100
0.5
5
4
2
100
2
PC3H3J00000F
AC input response,
high resistance to noise *1
±50
2.5
80
20
±1
5
4
2
100
2
PC3H4J00000F
AC input response
*2, 6
±50
2.5
80
20
±1
5
4
2
100
2
PC3H41xNIP0F
AC input response,
high resistance to noise* 1,
low input current
±10
2.5
80
50
±0.5
5
4
2
100
2
PC3H5J00000F
High sensitivity
50
2.5
35
600
1
2
60
2
100
2
10
2.5
35
600
0.5
2
60
2
100
2
PC3H510NIP0F
High sensitivity,
low input current
Mini-flat
4-pin
Mini-flat
4-pin
CMR: MIN.10 kV/µs
A VDE approved type is optionally available.
Please refer to Specification Sheets for model numbers approved by safety standards.
VDE, CSA approved
In conformance with BSI, SEMKO, DEMKO, NEMKO, and FIMKO
UL, cUL approved
PC3HU7xYIP0B
42
: Approved
Approved
by safety
standards*3
PC3H7J00000F
(Mini-flat 4-pin)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOCOUPLERS
Model No.
Internal
connection
diagram
: Approved
(Ta = 25°C)
Absolute maximum ratings
Isolation CollectorForward
Package current voltage emitter
(AC)
voltage
VDE Others
IF
UL
Viso (rms) VCEO
*3
*2
(mA)
(V)
(kV)
Approved by
safety standards*8
Features
Electro-optical characteristics
Current transfer ratio Response time
CTR
(%)
MIN.
IF
(mA)
tr
RL
(µs) (Ω)
TYP.
PC123XNNSZ0F* 1, *5, *6, *7
High isolation voltage,
reinforced insulation
50
5.0
70
50
5
4
100
PC1231xNSZ0X* 1
High isolation voltage, reinforced
insulation, low input current,
high resistance to noise *4
10
5.0
70
50
0.5
4
100
PC817XNNSZ0F* 5, *6, *7
High isolation voltage
–
*9
50
5.0
80
50
5
4
100
PC8171xNSZ0X* 5, *6
High isolation voltage, low input
current, high resistance to noise *4
–
–
10
5.0
80
100
0.5
4
100
PC851XNNSZ0F* 5, *6
High isolation voltage,
high collector-emitter voltage
–
–
50
5.0
350
40
5
4
100
PC815XNNSZ0F* 5, *6
High isolation voltage,
high sensitivity
–
–
50
5.0
35
600
1
60
100
PC81510NSZ0X
High isolation voltage,
high sensitivity, low input current
–
–
10
5.0
35
600
0.5
60
100
PC852XNNSZ0F* 5, *6
High isolation voltage,
high collector-emitter voltage
–
50
5.0
350
1 000
1
100 100
PC853XNNSZ0F* 5, *6
High isolation voltage,
high collector-emitter voltage
–
50
5.0
350
1 000
1
100 100
4-pin
DIP
Optoelectronics
Darlington phototransistor output
Single phototransistor output
Output type
◆Phototransistor Output Type
*1
*2
*3
*4
*5
*6
*7
Wide lead spacing type is also available. Creepage distance: 6.4 mm or more, wide lead spacing type: 8 mm or more.
Optionally available.
BSI, SEMKO, DEMKO, NEMKO, FIMKO, CSA
CMR: 10 kV/µs MIN.
Lead forming type is also available for surface mounting.
Taped package of lead forming type for surface mounting is also available.
Wide lead spacing type is also available. Compatible with wide lead spacing type lead-forming models for surface-mount use. Also compatible with taped packages for wide
lead spacing type lead-forming models for surface-mount use.
*8 Please refer to Specification Sheets for model numbers approved by safety standards.
*9 UL, CSA approved
PC817XNNSZ0F
(4-pin DIP)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
43
OPTO
PHOTOCOUPLERS
Darlington phototransistor output
Single phototransistor output
Output type
◆Phototransistor Output Type
Model No.
Internal
connection
diagram
: Approved, o: Under application
Features
UL
(Ta = 25°C)
Absolute maximum ratings
Electro-optical characteristics
Isolation Collector- Current transfer Response
Forward
ratio
time
emitter
Package current voltage
(AC)
voltage CTR
IF
tr
RL
I
F
Viso (rms) VCEO
(%)
(mA) (µs)
(Ω)
VDE*1
(mA)
(kV)
(V)
MIN.
TYP.
Approved
by safety
standards*2
PC714V0NSZXF
High isolation voltage
50
5.0
80
50
5
4
100
PC724V0NSZXF
High isolation voltage,
large input current
–
150
5.0
35
20
100
4
100
PC713V0NSZXF
High isolation voltage,
with base terminal
50
5.0
80
50
5
4
100
6-pin
DIP
PC715V0NSZXF
High isolation voltage,
high sensitivity
50
5.0
35
600
1
60
100
PC725V0NSZXF
High isolation voltage,
high sensitivity,
high collector-emitter voltage,
high power
50
5.0
300
1 000
1
100
100
*1 Optionally available.
*2 Please refer to Specification Sheets for model numbers approved by safety standards.
PC713V0NSZXF
(6-pin DIP)
44
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOCOUPLERS
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
◆OPIC Output ( light-detecting element and signal-processing circuit integrated onto a single chip.
: Approved
(1-1)
Model No.
A
PC456L0NIP0F ▲
A
PC410L0NIP0F
PC410S0NIP0F
PC4D10SNIP0F
(Ta = 25°C)
Absolute maximum
Electro-optical characteristics*1
ratings
Isolation
Low level output voltage
Threshold input current
Package Forward voltage
current
IFHL
VOL
IFLH
(AC)
Ta
IOL
RL
IF
IF
UL VDE*3
(mA) (mA)
Viso (rms) (V)
(°C)
(mA) (mA)
(Ω)
(mA)
MAX.
MAX. MAX.
(kV)
Approved by
safety
standards*2
Internal
connection
diagram
PC400J00000F
)
Features
Digital output,
normal-off operation
Built-in preamplifier,
high speed transmission
(2 Mb/s),
for flow soldering
High speed (10 Mb/s),
High CMR (10 kV/µs),
For flow soldering
High speed (10 Mb/s),
high CMR (10 kV/µs),
for flow soldering,
Solder heat resistance:
270°C
High speed (10 Mb/s),
for flow soldering,
Solder heat resistance:
270°C
2ch output
–
–
50
3.75
0.4
0 to +70
16
4
2.0
–
280
25
3.75
0.6
–40 to +85
2.4
10
5.0
–
20 k
20
3.75
0.6
–40 to +85
13
5
5.0
–
350
SOP
8-pin
20
3.75
0.6
–40 to +85
13
5
5.0
–
350
SOP
8-pin
20
3.75
0.6
–40 to +85
13
5
5.0
–
350
Mini-flat
5-pin
(1-2)
Model No.
Internal
connection
diagram
: Approved
Optoelectronics
A: Rated voltage circuit
*1 Each item is measured at Vcc=5V. (PC400)
*2 Please refer to Specification Sheets for model numbers approved by safety standards.
*3 Optionally available.
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
(Ta = 25°C)
Absolute maximum
Electro-optical characteristics
ratings
Isolation
Current transfer ratio
Propagation delay time
Package Forward voltage
current
tPHL tPLH
CTR
(AC)
IF
RL
VO VCC
IF
IF
VDE*2
Viso (rms) (%) (mA) (V) (V) (µs) (µs)
(Ω) (mA)
(mA)
MIN.
TYP. TYP.
(kV)
Approved by
safety
standards*1
Features
UL
PC457L0NIP0F
High speed (1 Mb/s),
high CMR (15 kV/µs),
for flow soldering
Mini-flat
5-pin
25
3.75
19
16
0.4
4.5
0.2
0.4
1 900
16
PC457S0NIP0F
High speed (1 Mb/s),
high CMR (15 kV/µs),
for flow soldering,
Solder heat resistance:
270°C
SOP
8-pin
25
3.75
19
16
0.4
4.5
0.2
0.3
1 900
16
*1 Please refer to Specification Sheets for model numbers approved by safety standards.
*2 Optionally available.
PC400J00000F
(Mini-flat 5-pin)
PC410S0NIP0F
(SOP 8-pin)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
45
OPTO
PHOTOCOUPLERS
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
◆OPIC Output ( light-detecting element and signal-processing circuit integrated onto a single chip.
: Approved
Internal
connection
diagram
Model No.
Features
PC900V0NSZXF* 2, *3
Digital output,
normal-off operation
A
(Ta = 25°C)
Absolute
maximum ratings
Approved by
safety
standards*5
UL
)
Electro-optical characteristics*1
Threshold input
Isolation
Low level output voltage
Package Forward voltage
current
current
(AC)
I
V
OL
FHL
IFLH
IF
Ta
IOL
RL
IF
VDE
Viso (rms) (V)
(mA) (mA)
(mA)
(°C)
(mA)
(mA)
(Ω)
*4
(kV)
MAX.
MAX. MAX.
6-pin
DIP
50
5.0
0.4
0 to +70
16
4
2.0
–
280
A: Rated voltage circuit
*1 Each item is measured at Vcc=5V.
*2 Lead forming type is also available for surface mounting.
*3 Taped package of lead forming type for surface mounting is also available.
*4 Optionally available.
*5 Please refer to Specification Sheets for model numbers approved by safety standards.
PC900V0NSZXF
(6-pin DIP)
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
◆OPIC Output ( light-detecting element and signal-processing circuit integrated onto a single chip.
: Approved
Model No.
Internal
connection
diagram
PD
PC942J00000F ▲
PC928J00000F
Tr1
Tr2
Interface
Amplifier
Interface
Amplifier
PC929J00000F
Interface
OPIC
PC925LxNSZ0F* 1
Interface
Amplifier
Approved by
safety
standards*3
Features
Package
UL
VDE
*2
• Built-in drive circuit
directly connectable to
MOS-FET and IGBT
• Peak output current: 2.5 A
• Low dissipation current
(Icc = TYP. 2.5 mA)
• High resistance to noise
(CMR: MIN. 15 kV/µs)
For controlling invertercontrolled air-conditioner
For driving inverter IGBT,
built-in short
protection circuit
For driving inverter IGBT,
high speed, built-in short protection circuit
)
(Ta = 25°C)
Absolute
Electro-optical characteristics
maximum ratings
Isolation
Propagation delay time
Forward
voltage
current
t
PHL
PLH
t
(AC)
VCC
RL2
IF
RL1
IF
Viso (rms) (µs) (µs)
(V) (mA) (Ω)
(Ω)
(mA)
TYP.
TYP.
(kV)
MAX. MAX. 15 to
0.5
0.5
30
7 to
16
RG =
10
–
6
5
5
10
1.0
24
10
RG =
47
–
0.3
24
5
RG =
47
–
25
5.0
25
5.0
2.0
2.0
25
4.0
1.0
20
4.0
0.3
8-pin
DIP
14-pin SMT
(Half pitch
lead)
*1 Lead forming type is also available for surface mounting. Taped package of lead forming type for surface mounting is also available.
*2 A VDE approved type is optionally available.
*3 Please refer to Specification Sheets for model numbers approved by safety standards.
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
PC925LENSZ0F, PC942J00000F▲
(8-pin DIP)
46
PC928J00000F
(PC929J00000F)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOTRIAC COUPLER LINEUP
■ Phototriac Coupler Lineup
Package
Mini-flat (SMD)
Applied voltage
AC 200 V lines
(VDRM = 600V)
ON-state
current (rms)
0.05 A
Features
AC 200 V lines
(VDRM = 600V)
0.1 A
Page
S2S3000F*3 / S2S5A00F*3 / S2S5FA0F*3
48
S2S4000F*3
49
PC3ST11NSZAX* 3
48
PC3ST21NSZBX* 2
49
PC3SH11YFZAX* 3 / PC3SH13YFZAX* 3
48
PC3SH21YFZBX* 2
49
General purpose
PC2SD11NTZAF* 3 / PC1S3021NTZF* 4
48
General purpose
PC3SD12NTZAF* 3 / PC3SD12NTZBF* 2 /
PC3SD12NTZCF* 1 / PC1S3052YTZF* 3 /
PC3SD11NTZCF* 1 / PC3SD13NTZBF* 2
48
PC3SD21NTZAF* 3 / PC3SD21NTZBF* 2 /
PC3SD21NTZCF* 1 / PC3SD21NTZDF* 5 /
PC3SD23YTZCF* 1 / PC1S3063YTZF* 1
49
PC3SF11YVZAF* 3 / PC3SF11YVZBF* 2 /
PC3SF13YVZBF* 2
48
PC3SF21YVZAF* 3 / PC3SF21YVZBF* 2 /
PC3SF23YVZSF* 2
49
PC4SD11NTZBF* 2 / PC4SD11NTZCF* 1
48
PC4SD21NTZCF* 1 / PC4SD21NTZDF* 5
49
PC4SF11YVZAF* 3 / PC4SF11YVZBF* 2
48
PC4SF21YVZBF* 2 / PC4SF21YVZCF* 1 /
PC4SF21YWPSF* 2
49
General purpose
Built-in zero-cross circuit
DIP type
Model No.
General purpose
Built-in zero-cross circuit
Reinforced isolation
Built-in zero-cross circuit
DIP type
(6-pin package,
5th-pin cut)
AC 100 V lines
(VDRM = 400V)
AC 200 V lines
(VDRM = 600V)
0.1 A
0.1 A
Built-in zero-cross circuit
Reinforced isolation
Built-in zero-cross circuit
AC 200 V lines
(VDRM = 800V)
0.1 A
General purpose
Built-in zero-cross circuit
Reinforced isolation
Built-in zero-cross circuit
Optoelectronics
(4-pin)
Minimum trigger current: *1 IFT & 5 mA, *2 IFT & 7 mA, *3 IFT & 10 mA, *4 IFT & 15 mA, *5 IFT & 3 mA
47
OPTO
PHOTOTRIAC COUPLERS
■ Phototriac Couplers
: Approved
(Ta = 25°C)
Approved by
safety standards*4
Model No.
Internal
connection
diagram
S2S3000F
Features
200 V lines, compact
UL,
CSA
Electro-optical
Absolute maximum ratings
characteristics
Min. trigger
Repetitive
Isolation
current
peak
Package ON-state
voltage
IFT
current OFF-state
(AC)
VDE Others
voltage
(mA) MAX.
IT (rms)
Viso (rms)
(A)
VDRM
VD = 6 V,
(kV)
RL = 100Ω
(V)
*6
–
S2S5A00F
200 V lines, compact
*6
–
S2S5FA0F
High impulse noise product
*6
–
PC3ST11NSZAX
PC3SH11YFZAX
PC3SH13YFZAX
PC2SD11NTZAF
200 V lines, compact
*6
–
200 V lines, compact,
reinforced isolation
200 V lines, compact,
reinforced isolation,
high noise resistance
*2
*2
100 V lines
–
–
10
Mini-flat
4-pin
0.05
3.75
10
10
600
4-pin
DIP
0.1
10
5.0
10
10
10
400
PC1S3021NTZF
100 V lines
–
*2
10
PC3SD12NTZAF
200 V lines
*6
–
10
PC1S3052YTZF
200 V lines
*6
*2
10
PC3SD12NTZBF
200 V lines
*6
–
PC3SD13NTZBF
High impulse noise product
*6
–
7
PC3SD12NTZCF
200 V lines
*6
–
5
PC4SD11NTZBF
200 V lines,
repetitive peak-OFF-state voltage
*6
–
PC3SD11NTZCF
200 V lines
*6
–
600
5
PC4SD11NTZCF
200 V lines,
repetitive peak-OFF-state voltage
*6
–
800
5
PC3SF11YVZAF
200 V lines, reinforced isolation
*2
PC3SF11YVZBF
200 V lines, reinforced isolation
*2
200 V lines, reinforced isolation,
high noise resistance
200 V lines, reinforced isolation,
repetitive peak-OFF-state voltage
200 V lines, reinforced isolation,
repetitive peak-OFF-state voltage
*2
*2
PC3SF13YVZBF
PC4SF11YVZAF
PC4SF11YVZBF
600
6-pin
DIP*1, 3
0.1
800
7
5.0
7
10
600
7
7
10
800
*2
7
For the notes *1 to *6, see next page.
48
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOTRIAC COUPLERS
■ Phototriac Couplers
(Built-in zero-cross circuit type)
: Approved
(Ta = 25°C)
Approved by
safety standards*4
S2S4000F
Internal
connection diagram
Zero-cross circuit
PC3ST21NSZBX
200 V lines, compact
200 V lines, compact
*6
Features
UL,
CSA
–
4-pin
DIP
7
0.1
600
5.0
200 V lines, compact,
reinforced isolation
200 V lines,
low zero-cross voltage: MAX. 20 V
200 V lines,
low zero-cross voltage: MAX. 20 V
200 V lines,
low zero-cross voltage: MAX. 20 V
100 V lines,
low zero-cross voltage: MAX. 20 V
200 V lines,
high pulse/noise resistance
(TYP. 2 kV)
200 V lines,
low zero-cross voltage: MAX. 20 V
200 V lines,
repetitive peak-OFF-state voltage
200 V lines,
repetitive peak-OFF-state voltage
*2
*6
–
10
*6
–
7
*6
–
*6
–
3
PC3SF21YVZAF
200 V lines, reinforced isolation
*2
10
PC3SF21YVZBF
200 V lines, reinforced isolation
*2
PC3SF23YVZSF
High impulse noise product
*2
7
200 V lines, reinforced isolation,
repetitive peak-OFF-state voltage
200 V lines, reinforced isolation,
repetitive peak-OFF-state voltage
*2
7
*2
High impulse noise product
*2
PC3SH21YFZBX
PC3SD21NTZAF
PC3SD21NTZBF
PC3SD21NTZCF
PC1S3063YTZF
PC3SD23YTZCF
PC3SD21NTZDF
Zero-cross circuit
PC4SD21NTZCF
PC4SD21NTZDF
PC4SF21YVZBF
PC4SF21YVZCF
PC4SF21YWPSF
*1
*2
*3
*4
*5
*6
*6
*2
–
*6
–
*6
–
7
5
600
5
5
3
6-pin
DIP*1, 3
0.1
800
5
5.0
600
Optoelectronics
Model No.
Electro-optical
Absolute maximum ratings
characteristics
Min. trigger
Repetitive Isolation
current
Package ON-state
peak
voltage
IFT
current
OFF-state
(AC)
VDE Others
(mA) MAX.
IT (rms)
VDRM Viso (rms)
(A)
VD = 4 V,
(V)
(kV)
RL = 100Ω
Mini-flat
*6
–
0.05
600
3.75
10*5
4-pin
7
800
5
6-pin
DIP*3
7
Lead forming type for surface mounting is also available.
In conformance with BSI, SEMKO, DEMKO, and FIMKO
These are molded pin No. 5.
Please refer to Specification Sheets for model numbers approved by safety standards.
VD = 6 V, RL = 100Ω
Optionally available
S2S3000F
(Mini-flat 4-pin)
PC2SD series
(PC3SD series, PC4SD series)
(6-pin DIP)
PC3SF series
(PC4SF series)
(6-pin DIP)
PC3ST series
(4-pin DIP)
PC3SH series
(4-pin DIP)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
49
OPTO
SOLID STATE RELAY LINEUP
■ Solid State Relay Lineup
Package
DIP 6-pin
DIP 8-pin
Applied voltage
Page
General purpose
PR22MA11NTZF
51
AC 200 V lines
0.06 A
General purpose
PR31MA11NTZF
51
0.15 A
General purpose
PR32MA11NTZF
51
0.3 A
General purpose
PR33MA series
51
0.3/0.6/0.9 A
General purpose
PR23MF11NSZF / PR26MF series /
PR29MF series
51
0.6/0.9 A
Built-in zero-cross circuit
PR26MF21NSZF / PR29MF21NSZF
51
0.3/0.6/0.9/1.2 A
General purpose
PR33MF5 series / PR39MF5 series /
PR36MF5 series / PR3BMF5 series
51
0.6/0.9/1.2 A
Built-in zero-cross circuit
PR36MF2 series / PR39MF2 series /
PR3BMF21NSZF
51
2/8 A
3 to 16 A
General purpose
S102T01F*1 / S108T01F*1 /
S101S05F / S102S01F / S112S01F / S116S01F
52
2/8 A
3 to 16 A
Built-in zero-cross circuit
S102T02F*1 / S108T02F*1 /
S101S06F / S102S02F / S116S02F
52
8A
Built-in snubber circuit
S102S11F
52
3/8 A
Built-in snubber circuit/
zero-cross circuit
S101S16F / S102S12F
52
General purpose
S202T01F*1 / S208T01F*1 /
S202S01F / S212S01F / S216S01F
52
2/8 A
3 to 16 A
Built-in zero-cross circuit
S202T02F*1 / S208T02F*1 /
S201S06F / S202S02F / S216S02F
52/53
8/8 A
Built-in snubber circuit
S202S15F / S202S11F
53
8A
Built-in snubber circuit/
zero-cross circuit
S202S12F
53
AC 100 V lines
AC 100 V lines
AC 200 V lines
50
Model No.
0.15 A
Low profile
*1 Low profile
Features
AC 100 V lines
AC 200 V lines
SIP 4-pin
ON-state current
(rms)
OPTO
SOLID STATE RELAYS
✩New product
■ Solid State Relays
: Approved
Approved by
safety standards*1
Model No.
Internal
connection
diagram
Features
UL
(Ta = 25°C)
Electrical
characteristics
Min. trigger
Repetitive Isolation
current
Package ON-state
peak
voltage
IFT
current
OFF-state
CSA VDE*2
(AC)
IT (rms)
(mA) MAX.
voltage Viso (rms)
VD = 6 V,
(A)
VDRM (V)
(kV)
RL = 100Ω
PR22MA11NTZF
100 V lines,
150 mA model in a small package
PR31MA11NTZF
200 V lines, compact
Absolute maximum ratings
0.15
6-pin
DIP
400
10
0.06
10
5.0
200 V lines,
150 mA model in a small package
200 V lines,
300 mA model in a small package
0.3
15
PR23MF11NSZF
100 V lines, compact
–
0.3
10
PR26MF11NSZF
100 V lines, compact
–
PR32MA11NTZF
✩PR33MA series
10
600
10
0.6
100 V lines, compact,
low input current
–
PR29MF11NSZF
100 V lines, compact
–
PR29MF12NSZF
100 V lines, compact,
low input current
–
PR33MF51NSLF
200 V lines, compact
PR26MF12NSZF
0.15
400
5
10
0.9
5
10
PR33MF52NSLF
200 V lines, compact
PR36MF51NSLF
200 V lines, compact
PR36MF12NSZF
PR39MF51NSLF
PR39MF12NSZF
PR3BMF51NSLF
PR3BMF52NSZF
PR26MF21NSZF
PR29MF21NSZF
PR36MF21NSZF
PR36MF22NSZF
PR39MF21NSZF
PR39MF22NSZF
PR3BMF21NSZF
Zerocross
circuit
10
10
0.6
200 V lines, compact,
low input current
200 V lines, compact
5
600
200 V lines, compact,
low input current
200 V lines, compact
200 V lines, compact,
low input current
100 V lines, compact
(built-in zero-cross circuit)
100 V lines, compact
(built-in zero-cross circuit)
200 V lines, compact (built-in zerocross circuit)
200 V lines, compact (built-in zerocross circuit), low input current
200 V lines, compact (built-in zerocross circuit)
200 V lines, compact (built-in zerocross circuit), low input current
200 V lines, compact (built-in zerocross circuit)
Optoelectronics
0.3
8-pin
DIP
10
4.0
0.9
5
10
1.2
–
5
0.6
10
400
–
0.9
10
10
0.6
5
600
10
0.9
5
1.2
10
*1 Please refer to Specification Sheets for model numbers approved by safety standards.
*2 Optionally available.
PR22MA11NTZF
(6-pin DIP)
PR26MF21NSZF
(8-pin DIP)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
51
OPTO
SOLID STATE RELAYS
(1)
: Approved
Approved by
safety standards*6
Model No.
Internal
connection
diagram
Features
UL
CSA
S102T01F
100 V lines, low profile
S108T01F
100 V lines, low profile
–
–
100 V lines, low profile
(built-in zero-cross circuit)
100 V lines, low profile
(built-in zero-cross circuit)
–
–
S101S05F
100 V lines
S102S01F
100 V lines
S112S01F
(Ta = 25°C)
Absolute maximum ratings
Electrical
characteristics
Min. trigger current
Repetitive Isolation
Package ON-state
peak
voltage
current
IFT
OFF-state
(AC)
IT (rms)
voltage Viso (rms) (mA)
(A)
MAX.
VDRM(V)
(kV)
VD
(V)
RL
(Ω)
2
8
12
30
8*2
8
12
30
8
12
30
8*2
8
12
30
3*3
15
12
30
8*2
8
12
30
100 V lines
12*4
8
12
30
S116S01F
100 V lines
16*5
8
12
30
S101S06F
100 V lines (built-in zero-cross circuit)
15
6
30
8
6
30
8
6
30
8
12
30
S102T02F
S108T02F
Zerocross
circuit
Low
profile
4-pin
SIP
3.0
2
4.0
400
3*3
4-pin
SIP
3.0
100 V lines (built-in zero-cross circuit)
100 V lines (built-in zero-cross circuit)
16*5
100 V lines (built-in snubber circuit)
8*1
100 V lines (built-in snubber circuit,
built-in zero-cross circuit)
100 V lines (built-in snubber circuit,
built-in zero-cross circuit)
3*3
3.0
15
6
30
8*1
4.0
8
6
30
S202T01F
200 V lines, low profile
2
8
12
30
S208T01F
200 V lines, low profile
–
–
8
12
30
8
12
30
8
12
30
8
12
30
8
12
30
8
12
30
S102S02F
Zerocross
circuit
S116S02F
S102S11F
S101S16F
S102S12F
Zerocross
circuit
8*2
4.0
Low
profile
4-pin
SIP
8*2
3.0
200 V lines, low profile
(built-in zero-cross circuit)
200 V lines, low profile
(built-in zero-cross circuit)
–
–
8*2
S202S01F
200 V lines
8*2
S212S01F
200 V lines
–
–
S216S01F
200 V lines
–
–
S202T02F
S208T02F
Zerocross
circuit
4-pin
SIP
2
12*4
16*5
600
4.0
For the notes *1 to *6, see next page.
52
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
SOLID STATE RELAYS
(2)
: Approved
Approved by
safety standards*6
S201S06F
S202S02F
Zerocross
circuit
S216S02F
Features
Absolute maximum ratings
Repetitive Isolation
Package ON-state
peak
voltage
current
IFT
OFF-state
(AC)
IT (rms)
voltage Viso (rms) (mA)
(A)
MAX.
VDRM(V)
(kV)
UL
CSA
200 V lines (built-in zero-cross circuit)
3*3
200 V lines (built-in zero-cross circuit)
8*2
200 V lines (built-in zero-cross circuit)
–
16*5
–
4-pin
SIP
8*2
200 V lines (built-in snubber circuit)
–
–
S202S11F
200 V lines (built-in snubber circuit)
8*1
200 V lines (built-in snubber circuit,
built-in zero-cross circuit)
8*1
Zerocross
circuit
RL
(Ω)
15
6
30
8
6
30
8
6
30
15
12
30
8
12
30
8
6
30
4.0
S202S15F
S202S12F
3.0
VD
(V)
3.0
4.0
*1 Tc & 88°C
*2 Tc & 80°C
*3 Tc & 100°C
*4 Tc & 70°C
*6 Please refer to Specification Sheets for model numbers approved by safety standards.
S102T01F series
(Low profile 4-pin SIP)
600
*5 Tc & 60°C
Optoelectronics
Model No.
Internal
connection
diagram
(Ta = 25°C)
Electrical
characteristics
Min. trigger current
S102S02F series
(4-pin SIP)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
53
OPTO
PHOTOINTERRUPTER LINEUP
■ Photointerrupter Lineup
Output type
Single phototransistor
Package type
Compact
Outline
High resolution
High response speed
Case type
Darlington
phototransistor
High resolution
Model No. (series)
Page
PWB mounting type
GP1S396HCP0F / GP1S09xHCZ0F /
GP1S19xHCZ0F
Surface-mount type/
Soldering reflow
GP1S396HCPSF / GP1S296HCPSF /
GP1S092HCPIF / GP1S19xHCxSF
55
PWB mounting type, etc.
GP1S5x series
56
55
Horizontal slit,
High resolution
PWB mounting type
GP1S59J0000F
56
With connector
General purpose
Snap-in
GP1S173LCS2F / GP1S273LCS1F
56
Case type
General purpose
PWB mounting type, etc.
GP1L5x series
57
Wide gap
PWB mounting type
GP1L57J0000F
57
High voltage
PWB mounting type
GP1A98HCZ0F
57
Surface-mount type
GP1A98HCPSF
57
High resolution
With screw hole/
PWB mounting type
GP1A5x series
58
Wide gap
PWB mounting type
GP1A57HRJ00F
58
General purpose
Screw mounting type/Snap-in
GP1A173LCS3F / GP1A173LCS2F /
GP1A173LCSVF / GP1A273LCS1F
59
High sensitivity
Digital output
Mounting method
Compact
(OPIC output)
Case type
With connector
Output type
Package type
Outline
Mounting method
Single phototransistor
Leadless
Long focal distance
Surface-mount type
High response speed
Compact,
thin (leadless)
General purpose
OPIC output
With connector
Light modulation type,
Sensitivity adjusted
Model No. (series)
Page
GP2S700HCP
59
Surface-mount type
GP2S60
59
Screw mounting type/
Compact snap-in/
Inverter light countermeasures
GP2A25 series / GP2A28 series /
GP2A200LCS0F / GP2A230LRS0F /
GP2A231LRSAF / GP2A230LRSAF /
GP2A240LCS0F / GP2A250LCS0F
60
Detection type
Transmissive type
Outline (Output type etc.)
Case type
With encoder function
Digital 2 output
(phase A/B)
Page
PWB mounting type
GP1A057SGKLF
61
Resolution: 150 LPI
Linear scale slit pitch:
0.17 mm
PWB mounting type
GP1A057RBKLF
61
Resolution: 180 LPI
Linear scale slit pitch:
0.14 mm
With screw hole/
PWB mounting type
GP1A058SCK0F
61
Resolution: 300 LPI
Linear scale slit pitch:
0.0847 mm
With screw hole/
PWB mounting type
GP1A054RDKLF
61
Resolution for reading:
180 LPI
Pitch: 0.14 mm
Output resolution: 360 LPI
With screw hole/
PWB mounting type
GP1A101C2KSF
61
For amusement use
Screw mounting
GP1A204HCS0
61
Injection
For prism system (Single phototransistor)
Screw mounting
GP2S29SVJ00F
61
–
GP2A222HCKA
62
For amusement use (Pachinko ball sensor)
54
Model No. (series)
Resolution: 45 LPI
Linear scale slit pitch:
0.56 mm
Case type
With encoder function
Digital 2 output
(Multiplying output)
Reflective type
Mounting method
OPTO
PHOTOINTERRUPTERS (TRANSMISSIVE TYPE)
■ Photointerrupters
◆Single Phototransistor Output
Internal
connection
diagram
Features
GP1S092HCPIF
Wide gap, for soldering reflow,
surface mount compatible, with positioning boss
(4.5 × 2.6 × 2.9 [height] mm)
2.0
0.3
2.0
5
5
50
0.1
1
5
GP1S093HCZ0F
Wide gap (4.5 × 2.6 × 2.9 [height] mm)
2.0
0.3
2.0
5
5
50
0.1
1
5
GP1S094HCZ0F
Wide gap, with positioning pin,
(5.5 × 2.6 × 4.8 [height] mm)
3.0
0.3
0.8
5
5
50
0.1
1
5
GP1S096HCZ0F
Narrow gap (3.5 × 2.6 × 2.9 [height] mm)
1.0
0.3
2.0
5
5
50
0.1
1
5
1.7
0.3
3.0
5
5
50
0.1
1
5
1.5
0.3
3.0
5
5
50
0.1
1
5
1.1
0.3
2.0
5
5
50
0.1
1
5
1.1
0.3
2.0
5
5
50
0.1
1
5
1.0
0.2
3.0
5
5
50
0.1
1
5
1.2
0.12
2.0
5
5
30
0.1
1
5
1.2
0.12
2.0
5
5
30
0.1
1
5
2.0
0.3
2.0
5
5
50
0.1
1
5
GP1S195HCZSF
GP1S195HCPSF
Compact, wide gap,
size: 3.6 × 2.0 × 2.7 (height) mm
Compact, wide gap, surface mount compatible,
size: 3.4 × 2.0 × 2.7 (height) mm
GP1S196HCZ0F
Compact, low profile (3.1 × 2.0 × 2.7 [height] mm)
GP1S196HCZSF
GP1S196HCPSF
Surface mount, for soldering reflow,
compact, low profile (3.1 × 2.0 × 2.7 [height] mm)
Surface mount, for soldering reflow,
compact, low profile (2.5 × 1.8 × 1.9 [height] mm)
Straight lead type,
compact, low profile (2.26 × 1.4 × 1.6 [height] mm)
Surface mount, for soldering reflow,
compact, low profile (2.26 × 1.4 × 1.6 [height] mm)
High resolution, wide gap,
with mounting hole (4.5 × 2.6 × 4.5 [height] mm)
GP1S194HCZ0F
GP1S296HCPSF
GP1S396HCP0F
GP1S396HCPSF
GP1S097HCZ0F
Optoelectronics
Model No.
(Ta = 25°C)
Electro-optical characteristics
Detecting
and
Current transfer ratio
Response time
Slit width
emitting
tr
CTR
(mm)
I
F
V
CE
IC
RL VCE
gap
(µs)
(%)
(mA) (V)
(mA) (kΩ) (V)
(mm)
TYP.
MIN.
❇ Topr: –25 to +85°C
❇❇ GP1SxxxHCZxF: Sleeve package, GP1SxxxHCPxF: Taped package
GP1S092HCPIF
GP1S093HCZ0F
GP1S094HCZ0F
GP1S096HCZ0F
GP1S194HCZ0F
GP1S195HCPSF/
GP1S195HCZSF
GP1S196HCZ0F
GP1S196HCZSF/
GP1S196HCPSF
GP1S296HCPSF
GP1S396HCPSF
GP1S396HCP0F
GP1S097HCZ0F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
55
OPTO
PHOTOINTERRUPTERS (TRANSMISSIVE TYPE)
Model No.
(Ta = 25°C)
Internal
connection
diagram
Features
Electro-optical characteristics
Detecting
and
Current transfer ratio
Response time
Slit width
emitting
tr
CTR
(mm)
I
F
V
CE
IC
RL VCE
gap
(µs)
(%)
(mA) (V)
(mA) (Ω) (V)
(mm)
TYP.
MIN.
GP1S50J0000F
High resolution, both-side mounting type
GP1S51VJ000F
High resolution, side mounting type
3.0
0.5
2.5
20
5
GP1S52VJ000F
High resolution, PWB mounting type
3.0
0.5
2.5
20
5
GP1S53VJ000F
High resolution, PWB mounting type
5.0
0.5
2.5
20
5
3.0
0.5
2.5
20
2.0
0.15
2.0
5.0
0.5
4.2
0.5
High resolution, with positioning pin,
PWB mounting type
High resolution, with positioning pin,
PWB mounting type
High resolution, with positioning pin,
PWB mounting type
High resolution, horizontal slit, with positioning pin,
PWB mounting type
GP1S54J0000F
GP1S56TJ000F
GP1S58VJ000F
GP1S59J0000F
3.0
0.5
2.5
20
5
3
2
100
2
3
2
100
2
3
2
100
2
3
2
100
2
5
3
2
100
2
20
5
38
0.5
1 000
2
2.5
20
5
3
2
100
2
2.5
20
5
3
2
100
2
❇ Topr: –25 to +85°C
GP1S50J0000F
GP1S51VJ000F
GP1S52VJ000F
GP1S53VJ000F
GP1S54J0000F
GP1S56TJ000F
GP1S58VJ000F
GP1S59J0000F
Model No.
Internal
connection
diagram
(Ta = 25°C)
Features
Electro-optical characteristics
Detecting
and
Current transfer ratio
Response time
Slit width
emitting
tr
CTR
(mm)
IF
VCE
IC
RL VCE
gap
(µs)
(%)
(mA) (V)
(mA) (Ω) (V)
(mm)
TYP.
MIN.
GP1S173LCS2F
Snap-in mounting integrated connector type
Applicable to 3 kinds of thickness of mounting boards
5.0
0.5
2.5
20
5
3
2
100
2
GP1S273LCS1F
Snap-in mounting integrated connector type
Applicable to 3 kinds of thickness of mounting boards
Compact (Compatible with 1.5 mm pitch connector)
5.0
0.7
2.5
20
5
3
2
100
2
❇ Topr: –25 to +85°C, –30 to +95°C (GP1S173LCS2F, GP1S273LCS1F)
GP1S173LCS2F
56
GP1S273LCS1F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOINTERRUPTERS (TRANSMISSIVE TYPE)
◆Darlington Phototransistor Output
Model No.
Internal
connection
diagram
(Ta = 25°C)
Electro-optical characteristics
Detecting
and
Current transfer ratio
Response time
Slit width
emitting
tr
CTR
(mm)
IF
VCE
IC
RL VCE
gap
(µs)
(%)
(mA) (V)
(mA) (Ω) (V)
(mm)
TYP.
MIN.
Features
GP1L50J0000F
High sensitivity, both-side mounting type
3.0
0.5
50
1
2
80
2
100
2
GP1L51J0000F
High sensitivity, side mounting type
3.0
0.5
50
1
2
80
2
100
2
GP1L52VJ000F
High sensitivity, PWB mounting type
3.0
0.5
50
1
2
80
2
100
2
GP1L53VJ000F
High sensitivity, PWB mounting type
5.0
0.5
30
1
2
80
2
100
2
GP1L57J0000F
High sensitivity, wide gap, PWB mounting type
10.0
1.8
70
1
2
130
2
100
2
❇ Topr: –25 to +85°C
GP1L50J0000F
GP1L51J0000F
GP1L52VJ000F
GP1L53VJ000F
GP1L57J0000F
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
◆OPIC Type ( light-detecting element and signal-processing circuit integrated onto a single chip. )
GP1A98HCZ0F
GP1A98HCPSF
Internal
connection
diagram
Voltage
regulator
Amplifier
Features
Optoelectronics
Model No.
(Ta = 25°C)
Electro-optical characteristics
Detecting
and
Threshold input current
Propagation delay time
Slit width
emitting
tPLH
IFHL
tPHL
IFLH
(mm)
VCC
IF
RL
RL
gap
(mA) (mA)
(µs)
(µs)
(V)
(mA) (kΩ)
(kΩ)
(mm)
MAX. MAX.
TYP. TYP.
VCC
(V)
Compact, PWB mounting
3.2
0.5
8
–
3.3 to 3.9 to
24
20
2.0
10.0
10
3.9 to 3.3 to
20
24
Compact, surface mount
3.2
0.5
8
–
3.3 to 3.9 to
24
20
2.0
10.0
10
3.9 to 3.3 to
20
24
❇ Topr = –25 to +85°C
GP1A98HCZ0F
GP1A98HCPSF
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
57
OPTO
PHOTOINTERRUPTERS (TRANSMISSIVE TYPE)
(Ta = 25°C)
Internal
connection
diagram
Model No.
Features
GP1A50HRJ00F
GP1A51HRJ00F
Voltage
regulator
Amplifier
GP1A52HRJ00F
Detecting
and
Slit width
emitting
(mm)
gap
(mm)
GP1A53HRJ00F
(When light is cut off:
low level)
GP1A58HRJ00F
Threshold input current
IFLH
IFHL
VCC
(mA)
(mA)
(V)
MAX.
MAX.
tPLH
(µs)
TYP.
Propagation delay time
tPHL
IF
RL
(µs)
(mA) (Ω)
TYP.
VCC
(V)
Both-side mounting,
with screw hole
3.0
0.5
5
–
5
3
5
5
280
5
Side mounting, with screw hole
3.0
0.5
5
–
5
3
5
5
280
5
PWB mounting type
3.0
0.5
5
–
5
3
5
5
280
5
PWB mounting type
5.0
0.5
8
–
5
3
5
8
280
5
10.0
1.8
7
–
5
3
5
7
280
5
5.0
0.5
8
–
5
3
5
8
280
5
3.0
0.5
–
5
5
5
3
5
280
5
PWB mounting type,
with positioning pin
PWB mounting type,
with positioning pin
GP1A57HRJ00F
Electro-optical characteristics
Voltage
regulator
Amplifier
GP1A52LRJ00F
PWB mounting type
(When light is cut off:
high level)
❇ Topr = –25 to +85°C
GP1A50HRJ00F
58
GP1A51HRJ00F
GP1A52LRJ00F
(GP1A52HRJ00F)
GP1A53HRJ00F
GP1A58HRJ00F
with positioning pin
GP1A57HRJ00F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
PHOTOINTERRUPTERS
(TRANSMISSIVE TYPE)/(REFLECTIVE TYPE)
OPTO
✩New product
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
◆OPIC Type ( light-detecting element and signal-processing circuit integrated onto a single chip.
Model No.
Internal
connection
diagram
Voltage
regulator
Amplifier
GP1A173LCSVF
GP1A273LCS1F
Voltage
regulator
Amplifier
GP1A75EJ000F ▲
with 3-pin connector
GP1A173LCS2F
(Ta = 25°C)
Electro-optical characteristics
Supply voltage
Low level output voltage
VCC
VOL
Light
IOL
VCC
(V)
(V)
cut-off
(mA)
(V)
MIN.
MAX.
MAX.
Detecting
and
Slit width
emitting
(mm)
gap
(mm)
Features
✩GP1A173LCS3F
)
Snap-in mounting integrated
connector type*1
Snap-in mounting integrated
connector type*1
Snap-in mounting integrated
connector type*1,
enforced electrostatic discharge
(ESD) type
Integrated connector, compatible
with 1.5 mm pitch connector,
snap-in mounting type* 1
Either-side mounting type
Screw mounting type
5.0
0.5
2.7
5.5
0.35
No
4
3.3
5.0
0.5
4.5
5.5
0.35
No
4
5
5.0
0.5
4.5
5.5
0.35
No
4
5
5.0
0.7
4.5
5.5
0.35
No
4
5
5.0
0.5
4.5
5.5
0.35
Yes
16
5
GP1A173LCS3F,
GP1A173LCS2F,
GP1A173LCSVF
GP1A273LCS1F
Optoelectronics
❇ Topr: –20 to +75°C, –30 to +95°C (GP1A173LCS3F, GP1A173LCS2F, GP1A173LCSVF, GP1A273LCS1F)
*1 Applicable to 3 kinds of thickness of mounting boards.
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
GP1A75EJ000F▲
■ Photointerrupters
◆Single Phototransistor Output
Model No.
Internal
connection
diagram
(Ta = 25°C)
Features
Electro-optical characteristics
Optimum
detecting
Current transfer ratio
Response time
distance CTR (%)
IF
VCE
tr (µs)
IC
RL
(mm)
MIN.
(mA)
(V)
TYP. (mA) (kΩ)
VCE
(V)
GP2S700HCP
Compact (4 × 3 × 2 [height] mm),
long focal distance, surface mounting leadless type
4
1.5
4
2
20
0.1
1
2
GP2S60
Thin (3.2 × 1.7 × 1.1 [height] mm), surface mounting
leadless type
1
1.0
4
2
20
0.1
1
2
❇ Topr: –25 to +85°C
GP2S700HCP
GP2S60
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
59
OPTO
PHOTOINTERRUPTERS (REFLECTIVE TYPE)
“OPIC” (Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
◆OPIC Output ( light-detecting element and signal-processing circuit integrated onto a single chip.
Internal
connection
diagram
Model No.
GP2A200LCS0F
GP2A240LCS0F
GP2A250LCS0F
GP2A25J0000F
GP2A230LRS0F
GP2A230LRSAF
GP2A231LRSAF ▲
GP2A25NJJ00F
GP2A25DJ000F
GP2A28AJ000F
)
(Ta = 25°C)
Electro-optical characteristics
Optimum
Supply voltage Dissipation current Low level output voltage
detecting
VCC
VOL
ICC
distance
VCC
VCC
(V)
(mA)
(V)
(mm)
(V)
(V)
MIN. MAX. MAX.
MAX.
Features
Multi types of paper detectable, light modulation type,
with connector, sensitivity adjusted
Applicable to inverter fluorescent lamp,
light modulation type, with connector, sensitivity adjusted
(Following
diagram [A]) Static electricity resistant,
applicable to inverter fluorescent lamp,
light modulation type, with connector, sensitivity adjusted
Multi types of paper detectable, light modulation type,
with connector, sensitivity adjusted
Compact, hook type (GP2A231LRSAF),
(Following
multi types of paper detectable, light modulation type,
diagram [B])
with connector
Multi types of paper detectable, light modulation type,
sensitivity adjusted, improved light-resistance characteristic
for inverter lighting, built-in visible light cut filter
(Following
Multi types of paper detectable, light modulation type,
diagram [A])
with connector, sensitivity adjusted
Multi types of paper detectable, light modulation type,
with connector, sensitivity adjusted, hook type
5 to 15
4.75
5.25
30*1
5
0.4
5
5 to 15
4.75
5.25
30*1
5
0.4
5
2.5 to
12.5
4.75
5.25
30*1
5
0.4
5
3 to 7
4.75
5.25
30*1
5
0.4
5
3 to 7
4.75
5.25
20*1
5
0.4
5
3 to 7
4.75
5.25
30*1
5
0.4
5
3 to 7
4.75
5.25
30*1
5
0.4
5
3 to 7
4.75
5.25
30*1
5
0.4
5
❇ Topr: –10 to +60°C (GP2A25J0000F, etc.)
–10 to +70°C (GP2A200LCS0F, GP2A240LCS0F, GP2A250LCS0F, GP2A230LRS0F, GP2A230LRSAF, GP2A231LRSAF)
*1 Smoothing value R L = ∞
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
[Internal connection diagram]
[A]
Voltage regulator
Demodulator
GP2A25J0000F
Amplifier
Comparator
Oscillator
Synchronous detector
GP2A25NJJ00F, GP2A200LCS0F,
GP2A240LCS0F
GP2A250LCS0F
[B]
Voltage regulator
Demodulator
(10kΩ)
Amplifier
GP2A25DJ000F
Comparator
60
Oscillator
GP2A230LRS0F
GP2A231LRSAF▲
GP2A28AJ000F
Synchronous detector
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PHOTOINTERRUPTERS FOR SPECIFIC APPLICATIONS
■ Photointerrupters for Specific Applications
◆Transmissive Type
(Ta = 25°C)
Absolute maximum ratings
Electro-optical characteristics
Vcc
(V)
Topr
(°C)
GP1A057RBKLF
GP1A054RDKLF
GP1A057SGKLF
GP1A058SCK0F
6
6
6
6
–10 to +70
–10 to +70
–10 to +70
–10 to +70
Operating
voltage
Vcc (V)
TYP.
3.3
3.3
3.3
3.3
GP1A101C2KSF
6.5
–10 to +70
3.3
Model No.
Response frequency
Output signal
Resolution
f (kHz)
MAX.
IF (mA)
60
60
25
60
20
20
20
20
Dissipation
current
(output side)
Icc (mA) MAX.
7
5.5
5.5
5.5
120
20
20
Linear scale slit pitch 0.17 (mm) (150LPI)
Linear scale slit pitch 0.0847 (mm) (300LPI)
Linear scale slit pitch 0.56 (mm) (45LPI)
Linear scale slit pitch 0.14 (mm) (180LPI)
Resolution for reading: 180 LPI
Digital 2 output
(Pitch: 0.14 mm)
(Multiplying output)
Output resolution: 360 LPI
Digital 2 output
(Phase A/B)
* High precision read and low affection of angle error from vibration thanks to the multi-segment PD system.
Duty ratio: 50±15%, phase difference: 90±45°
GP1A057RBKLF
(GP1A057SGKLF)
GP1A058SCK0F
GP1A101C2KSF
Model No.
Internal
connection
diagram
(Ta = 0 to +40°C)
Features
Detecting
and emitting
gap
(mm)
Slit width
(mm)
4.0
0.5
Electro-optical characteristics
Operating voltage
Low level output voltage
Vcc (V)
IOL
VCC
VOL (V) Light
MIN.
MAX.
MAX. cut-off
(mA)
(V)
Optoelectronics
GP1A054RDKLF
Voltage regulator
Connector with lock,
screw mounting type,
high resistant to noise
GP1A204HCS0
10.8
24
0.4
Yes
5
10.8 to 24
Amplifier
GP1A204HCS0
◆Reflective Type
Model No.
GP2S29SVJ00F
❇ Topr: –25 to +85°C
Internal
connection
diagram
(Ta = 25°C)
Electro-optical characteristics
Peak photocurrent
Response time
IF
VCE
tr (µs)
IC
RL
ICP
(mA)
(mA)
(V)
TYP.
(mA)
(kΩ)
Features
Long focal distance (with prism system*1),
compact, screw mounting type
0.4 to
3.0*1
20
5
38
0.5
1
VCE
(V)
2
*1 Space between prism and sensor is 8 mm.
GP2S29SVJ00F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
61
OPTO
PHOTOINTERRUPTERS FOR SPECIFIC APPLICATIONS /
PROXIMITY SENSOR
(Ta = 25°C)
Model No.
GP2A222HCKA
Electro-optical characteristics
Supply voltage
Dissipation current Response frequency
Vcc (V)
Icc (mA)
f (Hz)
Features
Employs reflective type, pinball detector, connector with lock
In conjunction with an IC, detects beam interruption*1
4.5 to 16.5
MAX. 12
MAX. 500
*1 Used together with interface IC for control (IR3N184)
GP2A222HCKA
■ Proximity Sensor
(Ta = 25°C)
Absolute maximum ratings
Model No.
GP2AP002S00F
62
Features
Compact size (4.0 × 2.0 × 1.25 t mm)
Drastically reduced LED current consumption by
employing a light modulation system
Built-in LEDs for simple optical design and I 2C output
VCC
(V)
Topr
(°C)
3.8
–25 to +85
Electro-optical characteristics
NonPeak
Detecting
detecting
Dissipation
emission
distance
distance
current
wavelength
Lon
Loff
Icc (µA)
λp
(mm)
(mm)
TYP.
(nm)
MIN.
MAX.
240
25
150
940
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
PROXIMITY SENSOR WITH INTEGRATED
AMBIENT LIGHT SENSOR
OPTO
✩New product
■ Proximity Sensor with Integrated Ambient Light Sensor
Absolute maximum ratings
Model No.
Features
LED and ambient light sensor
combined in a single package
(5.6 × 2.1 × 1.25 t mm)
Drastically reduced LED
current consumption by
employing a light modulation
GP2AP002A00F ▲
system
Built-in LEDs for simple optical
design
Proximity sensor: I2C output
Ambient light sensor: logarithmic current output
VCC
(V)
Topr
(°C)
3.8
–25 to
+85
(Ta = 25°C)
Electro-optical characteristics
Proximity sensor portion
Ambient light sensor portion
Output current
RecomNonDissipation Detecting
Peak
Peak
mended
detecting
current
sensitivity
emission
distance
illuminance
distance
Io1
Io2
Icc (µA)
wavelength
wavelength
Lon
range
Loff
(µA)
(µA)
TYP.
λp
λp
(mm)
Ev (lx)
(mm)
TYP.
MAX.
(nm)
(nm)
MIN.
MIN.
MAX.
270
25
150
940
3 to
55 000
30
1
(at Ev = (at Ev =
1 000 lx) 0 lx)
555
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
(Ta = 25°C)
Absolute maximum ratings
Electro-optical characteristics
Model No.
✩GP2AP030A00F
Features
LED and ambient light sensor combined in
a single package (4.0 × 2.1 × 1.25 t mm)
Built-in LEDs for simple optical design
Illuminance output: digital 16-bit output
(Minimum detectable illuminance: 0.02 lx)
I2C output compatible (proximity sensor,
ambient light sensor)
GP2AP002S00F
VCC
(V)
Topr
(°C)
5.5
–35 to
+85
65
GP2AP002A00F▲
Detecting
distance
Lon
(mm)
TYP.
100
Ambient light sensor portion
ADC
RecomPeak
conversion
mended
Output
emission
time
illuminance
resolution
wavelength
Tint
range
(bit)
λp
(ms)
Ev
(nm)
TYP.
(lx)
940
0.02 to
10 000
16
Optoelectronics
Proximity sensor portion
Dissipation
current
Icc
(µA)
TYP.
100
GP2AP030A00F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
63
PROXIMITY/GESTURE SENSOR WITH
INTEGRATED AMBIENT LIGHT SENSOR
OPTO
✩New product
■ Proximity/Gesture Sensor with Integrated Ambient Light Sensor
Absolute maximum ratings
(Ta = 25°C)
Electro-optical characteristics
Proximity/gesture
sensor portion
Model No.
✩GP2AP052A00F
Features
LED and ambient light sensor combined in
a single package (5.6 × 2.1 × 1.25 t mm)
Built-in LEDs for simple optical design
Illuminance output: digital 16-bit output
(Minimum detectable illuminance: 0.02 lx)
I2C output compatible
Gesture recognition: directional hand
movements detected without touching the
screen
VCC
(V)
Topr
(°C)
5.5
–35 to
+85
Ambient light sensor portion
DissipaDissipation
tion
ADC
Recomcurrent Detecting
Peak
current
conversion
mended
Icc
Output
distance
emission
Icc
time
illuminance
(Gesture)
resolution
Lon
wavelength
(µA)
Tint
range
(µA)
(bit)
(mm)
λp
TYP.
(ms)
Ev
TYP.
TYP.
(nm)
TYP.
(lx)
65
200
100
940
0.02 to
10 000
16
100
GP2AP052A00F
64
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
AMBIENT LIGHT SENSORS
■ Ambient Light Sensors
(Ta = 25°C)
Absolute maximum ratings
Type
Package
Built-in amplification circuit
Peak sensitivity characteristic close
to human visual sensitivity
GA1A2S100SS
Output characteristic: Linear current
output for illuminance
Lead frame (straight) type
Built-in amplification circuit
Peak sensitivity characteristic close
to human visual sensitivity
GA1A2S100LY
Output characteristic: Linear current
output for illuminance
Lead frame (L bend) type
Built-in amplification circuit
Peak sensitivity characteristic close
GA1A1S202WP to human visual sensitivity
Output characteristic: Logarithmic
current output for illuminance
Built-in amplification circuit
Peak sensitivity characteristic close
to human visual sensitivity
GA1A1S203WP ▲
Output characteristic: Logarithmic
current output for illuminance
Thin type
Built-in amplification circuit
Peak sensitivity characteristic close
to human visual sensitivity
GA1A1S204WP
Output characteristic: Logarithmic
current output for illuminance
Back-mount-available type
Built-in amplification circuit
Peak sensitivity characteristic close
GA1A1S100WP to human visual sensitivity
Output characteristic: Linear current
output for illuminance
Output current
Recommended Recommended Dissipation
Peak
Topr supply voltage illuminance
current
sensitivity
Io2
Io1
(°C)
VCC
Icc (µA) wavelength (µA)
range
(µA)
(V)
TYP.
Ev (lx)
λp (nm)
TYP.
TYP.
VCC
(V)
IO
(mA)
7.0
5
–40 to
+85
2.7 to 3.6
10 to 10 000
500
555
480
48
(at Ev = (at Ev =
1 000 lx) 100 lx)
7.0
5
–40 to
+85
2.7 to 3.6
10 to 10 000
500
555
48
480
(at Ev = (at Ev =
1 000 lx) 100 lx)
Compact SMD
(2.0 × 1.6
× 0.6 mm)
Leadless
7.0
1
–40 to
+85
2.3 to 3.2
3 to 55 000
70
555
30
20
(at Ev = (at Ev =
100 lx) 1 000 lx)
Compact SMD
(2.0 × 1.6
× 0.42 mm)
Leadless
7.0
1
–40 to
+85
2.3 to 3.2
3 to 55 000
70
555
20
30
(at Ev = (at Ev =
100 lx) 1 000 lx)
Compact SMD
(3.3 × 2.0
× 0.6 mm)
Back-mount
available,
leadless
7.0
1
–40 to
+85
2.3 to 3.2
3 to 55 000
70
555
30
20
(at Ev = (at Ev =
100 lx) 1 000 lx)
Compact SMD
(2.0 × 1.6
× 0.6 mm)
Leadless
7.0
10
–40 to
+85
2.7 to 3.6
10 to 5 000
1 460
555
1 420
142
(at Ev = (at Ev =
1 000 lx) 100 lx)
Transparent
epoxy resin
(3 × 4 mm)
Optoelectronics
Model No.
Electro-optical characteristics
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
GA1A2S100SS
GA1A2S100LY
GA1A1S202WP
(GA1A1S100WP)
GA1A1S203WP▲
GA1A1S204WP
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
65
OPTO
OPIC LIGHT DETECTORS
(Optical IC) is a trademark of SHARP Corporation. An OPIC consists of a
■ OPIC Light Detectors ( “OPIC”
light-detecting element and signal-processing circuit integrated onto a single chip. )
Absolute maximum ratings
Model No.
IS485E
IS486E
EVLH EVHL
(Ix)
(Ix)
MAX. MAX.
(Ta = 25°C)
Electro-optical characteristics
tPLH
tPHL
VCC
(µs)
(µs)
VCC
(V)
TYP.
TYP.
(V)
Type
Package
VCC
(V)
Built-in schmidt trigger
circuit, amplifier and
voltage regulator
Transparent
epoxy resin with
condenser (lens)
–0.5 to +17
175
50
–25 to +85
–
35
5
5
3
–0.5 to +17
175
50
–25 to +85
35
–
5
3
5
Topr
(°C)
P
IO
(mW) (mA)
EV
(Ix)
RL
(Ω)
5
50
280
5
50
280
IS485E
(IS486E)
(Ta = 25°C)
Absolute maximum ratings
Model No.
IS489E
Type
Package
Built-in Schmidt trigger
circuit and amplifier
Transparent
epoxy resin with
condenser (lens)
Topr
(°C)
Operating
supply
voltage (V)
–25 to +85
1.4 to 7.0
P
IO
(mW) (mA)
80
2
Electro-optical characteristics
EVLH EVHL
tPHL
tPLH
(Ix)
(Ix)
VCC
(µs)
(µs)
MAX. MAX.
(V)
TYP.
TYP.
–
15
3
1.3
8.5
VCC
(V)
EV
(Ix)
RL
(Ω)
3
125
3 000
IS489E
(Ta = 25°C)
Absolute maximum ratings
Model No.
IS471FE*1, *3
Type
Package
Built-in pulse driver
circuit at the emitter
Visible light
side, synchronous
cut-off epoxy
detector circuit,
resin
amplifier circuit and
demodulator circuit
VCC
(V)
–0.5 to +16
Topr
(°C)
VOL
(V)
MAX.
–25 to +60
0.35
P
IO
(mW) (mA)
250
50
Electro-optical characteristics*2
tPLH
tPHL
VOH
(V)
(µs)
(µs)
VCC
MIN.
TYP.
TYP.
(V)
4.97
400
400
5
RL
(Ω)
External
disturbing light
illuminance
EVDX(Ix) TYP.
280
7 000
*1 IS471FE is less susceptible to disturbing effects thanks to the light modulation system
*2 Vcc = 5 V
*3 Straight lead type (IS471FSE) is also available.
IS471FE
66
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
OPIC LIGHT DETECTORS
(Ta = 25°C)
Electro-optical characteristics
Model No.
GA220T2L2IZ▲
Type
2-PD, differential type
Package
Transparent epoxy resin
18-pin
Recommended supply
voltage
VCC
(V)
VOH
(V)
MIN.
VOL
(V)
MAX.
4.5 to 5.5
4.9
0.6
H → L delay time variation
∆tPHL
(ns) MAX.
±8.5
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
Optoelectronics
GA220T2L2IZ▲
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
67
PHOTOTRANSISTOR LINEUP /
PHOTOTRANSISTORS
OPTO
■ Phototransistor Lineup
Package
Epoxy resin with lens
Output type
Single phototransistor
Visible light
cut-off
Standard
General purpose/Narrow acceptance
±13°
PT480E00000F
PT480FE0000F
Compact, thin
±35°
PT4800E0000F
PT4800FE000F /
PT4850FE000F
High sensitivity/Narrow acceptance
±13°
PT481E00000F
PT481FE0000F
High sensitivity/Narrow acceptance/Long lead
±13°
—
PT483F1E000F ▲
High sensitivity/Intermediate acceptance
±40°
—
PT491FE0000F
Single phototransistor
Compact
(side view/top view mounting possible)
±15°
Darlington
phototransistor
Compact
(side view/top view mounting possible)
±15°
Darlington
phototransistor
Surface mounting
leadless type
Model No.
Half
sensitivity
angle
Features
PT100MC0MP
PT100MF0MP
—
PT100MF1MP
Type
■ Phototransistors
Model No.
PT100MC0MP
PT100MF0MP*1
Absolute maximum ratings
PC
Topr
VCEO
(V)
(mW)
(°C)
Package
Surface mounting
leadless type with lens
Single
PT480E00000F
PT480FE0000F* 1
PT4800E0000F
Epoxy resin with lens
Darlington
PT4800FE000F* 1
MIN.
Ic (mA)
VCE
MAX.
(V)
MAX.
VCE
(V)
∆θ
(°)
TYP.
λp
(nm)
TYP.
ICEO(A)
Ee
(mW/cm2)
35
75
–30 to +85
1.7
5.1
5
1
1 × 10–7
20
±15
900
35
75
–30 to +85
1.15
3.45
5
1
1 × 10–7
20
±15
910
35
75
–25 to +85
0.4
TYP. 1.7
5
1
1 × 10–7
20
±13
800
10–7
35
75
–25 to +85
0.25
TYP. 0.8
5
1
1×
20
±13
860
35
75
–25 to +85
0.12
TYP. 0.4
5
1
1 × 10–7
20
±35
800
35
75
–25 to +85
0.08
TYP. 0.25
5
1
1 × 10–7
20
±35
860
1×
10–7
PT4850FE000F* 1
35
75
–25 to +85
0.12
0.56
5
1
20
±35
860
PT481E00000F
35
75
–25 to +85
1.5
25
2
0.1
1 × 10–6
10
±13
800
10–6
PT481FE0000F* 1
PT483F1E000F* 1▲
PT491FE0000F* 1
PT100MF1MP*1
35
75
–25 to +85
0.9
27
2
0.1
1×
10
±13
860
35
75
–25 to +85
1.5
4.0
2
0.1
1 × 10–6
10
±13
860
35
75
–25 to +85
0.2
0.8
2
Ev, 2 Ix
1 × 10–6
10
±40
860
35
75
–30 to +85
0.2
1.2
5
0.01
1 × 10–6
10
±15
860
Epoxy resin with lens
Surface mounting
leadless type with lens
*1 Visible light cut-off type
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
PT100MF0MP
PT100MF1MP,
PT100MC0MP:
Transparent resin
68
PT480E00000F
PT480FE0000F,
PT481E00000F,
PT481FE0000F
PT4800E0000F
PT4800FE000F,
PT4810E0000F,
PT4850FE000F
PT483F1E000F▲
PT491FE0000F
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
PIN PHOTODIODES
■ PIN Photodiodes
PD410PI2E00F
PD411PI2E00F
PD412PI2E00F
PD413PI2E00F
PD100MC0MP
PD100MF0MP
Features
Package
(Material)
Visible light cut-off epoxy
resin with condenser (lens)
Transparent epoxy resin with
PIN type
condenser (lens)
Transparent epoxy resin with
condenser (lens)
PIN type
Visible light cut-off epoxy
IrDA1.0
resin with condenser (lens)
Surface mounting Transparent epoxy resin
leadless type
board with lens
Surface mounting Visible light cut-off epoxy
leadless type
resin board with lens
PD410PI2E00F
Active
area
(mm2)
Topr
(°C)
Isc
(µA)
MIN.
Ev
(Ix)
Id
(A)
MAX.
VR
(V)
tr, tf
(µs)
TYP.
VR
(V)
RL
(kΩ)
λp
(nm)
TYP.
3.31
–25 to +85
2.5
100
1 × 10–8
10
0.2
10
1
1 000
3.31
–25 to +85
5.0
100
1 × 10–8
10
0.2
10
1
960
3.31
–25 to +85
3.5
100
1 × 10–8
10
0.25
10
1
800
3.31
–25 to +85
MIN. 4.5
(TYP. 5.4)
100
1 × 10–8
10
0.2
10
1
960
–
–30 to +85
0.6
100
1 × 10–8
10
0.01
15
0.18
820
–
–30 to +85
0.4
100
1 × 10–8
10
0.01
15
0.18
850
PD411PI2E00F: transparent; PD412PI2E00F: transparent,
PD413PI2E00F
PD100MC0MP
(PD100MF0MP: black)
Optoelectronics
Model No.
(Ta = 25°C)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
69
INFRARED EMITTING DIODE LINEUP /
INFRARED EMITTING DIODES
OPTO
■ Infrared Emitting Diode Lineup
Type
Single-end lead
Package
Half intensity
angle
Features
Epoxy resin with lens
Model No.
General purpose/Narrow beam angle
±13°
GL480E00000F
Compact and thin
±30°
GL4800E0000F
Compact/Narrow beam angle
±10°
GL100MN0MP
±10°
GL100MN1MP
±80°
GL100MD1MP1
(Side view type)
Surface mount type
Epoxy resin with lens/
leadless
(Mountable for Top view/
Side view type)
High output type
Compact/Wide beam angle
■ Infrared Emitting Diodes
Model No.
Package, features
GL480E00000F
(Ta = 25°C)
Absolute maximum ratings
VR
P
Topr
IF
(mA) (V) (mW)
(°C)
Radiant flux Φe (mW)
IF
MIN.
TYP.
(mA)
TYP.
MAX.
IF
(mA)
∆θ
(°)
TYP.
λp
(nm)
TYP.
VF (V)
50
6
75
–25 to +85
0.7
–
20
1.2
1.4
20
±13
950
50
6
75
–25 to +85
0.7
1.6
20
1.2
1.4
20
±30
950
50
6
75
–30 to +85
1.0
3.0
(MAX.)
20
1.2
1.4
20
±10
940
50
6
75
–30 to +85
2.0
6.0
(MAX.)
20
1.2
1.5
20
±10
940
50
6
75
–30 to +85
–
6.0
(MAX.)
20
–
1.5
20
±80
940
Epoxy resin with lens
GL4800E0000F
GL100MN0MP
GL100MN1MP
GL100MD1MP1
Surface mounting leadless type,
epoxy resin board with lens
Surface mounting leadless type,
epoxy resin board with lens,
high output type
Surface mounting leadless type,
epoxy resin board with lens,
wide beam angle
GL480E00000F
70
GL4800E0000F
GL100MN0MP
(GL100MN1MP, GL100MD1MP1)
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
OPTICAL-ELECTRIC SENSOR LINEUP
■ Distance Measuring Sensor Lineup
Detected distance
1.5 cm
Features
Battery drive compatible, compact, 1-bit digital output
Capable of operation at high
temperature (–30 to +105°C)
Battery drive compatible, compact, 1-bit digital output
GP2Y0D805Z0F
10 cm
Battery drive compatible, compact, 1-bit digital output
GP2Y0D810Z0F
GP2Y0D810Z1F
15 cm
Battery drive compatible, compact, 1-bit digital output
GP2Y0D815Z0F
13 cm
1-bit digital output
GP2Y0D413K0F
24 cm
1-bit digital output
GP2Y0D21YK0F
80 cm
1-bit digital output
GP2Y0D02YK0F
Range of distance
measuring
Analog voltage output
according to distance
measuring
(Including I2C output)
GP2Y5D91S00F
5 cm
Wide operating temperature type
(–40 to +85°C)
Output
Model No.
Features
Model No.
1.5 to 15 cm
Analog output
GP2Y0AF15 series
2 to 15 cm
Analog output
GP2Y0A51SK0F
4 to 30 cm
Analog output
GP2Y0A41SK0F / GP2Y0AF30 series
Analog output
GP2Y0E02A
I2C output
GP2Y0E02B
Analog, I2C output
GP2Y0E03
10 to 80 cm
Analog output
GP2Y0A21YK0F
10 to 150 cm
Compact (22 × 8 × 7.2 [T] mm),
Analog output
GP2Y0A60SZ0F / GP2Y0A60SZLF
20 to 150 cm
Analog output
GP2Y0A02YK0F
100 to 550 cm
Analog output
GP2Y0A710K0F
4 to 50 cm
CMOS type
Optoelectronics
Output
1-bit digital output according
to distance measuring
■ High-Precision Displacement Sensor
Range of distance
measuring
Output
Voltage output according to
distance measuring
4.5 to 6.0 mm
Features
Resolution: 50 µm
Model No.
GP2Y0AH01K0F
■ Dust Sensor Unit Lineup
Output
Analog output
Features
Pulse analog output, single-shot detection of house dust,
general purpose
Model No.
GP2Y1010AU0F
71
OPTO
DISTANCE MEASURING SENSORS
■ Distance Measuring Sensors (1)
◆Digital Output
Model No.
GP2Y5D91S00F
1.5
GP2Y0D805Z0F
5
GP2Y0D810Z0F
10
GP2Y0D810Z1F
10
GP2Y0D815Z0F
15
GP2Y0D413K0F
13
GP2Y0D21YK0F
24
GP2Y0D02YK0F
80
*1 Vcc = 5 V
72
Detected
distance
(cm)
(Ta = 25°C)
Absolute maximum ratings
Features
Light detector,
infrared LED and signal processing circuit,
short distance measuring type,
battery drive compatible
(operating power supply: 2.7 to 6.2 V),
capable of operation at high temperature
Light detector,
infrared LED and signal processing circuit,
short distance measuring type,
battery drive compatible
(operating power supply: 2.7 to 6.2 V)
Light detector,
infrared LED and signal processing circuit,
short distance measuring type,
battery drive compatible
(operating power supply: 2.7 to 6.2 V)
Light detector,
infrared LED and signal processing circuit,
short distance measuring type,
battery drive compatible
(operating power supply: 2.7 to 6.2 V),
wide operating temperature type
Light detector,
infrared LED and signal processing circuit,
short distance measuring type,
battery drive compatible
(operating power supply: 2.7 to 6.2 V)
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
digital voltage output according to the measured
distance
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
digital voltage output according to the measured
distance
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
long distance measuring type
(No external control signal required),
digital voltage output according to the measured
distance
Electro-optical characteristics*1
Dissipation current
VOH
VOL
(V)
(V)
Operating Standby
MIN.
MAX.
(mA)
(µA)
Vcc
(V)
Topr
(°C)
–0.3 to +7
–30 to +105
Vcc –0.6
0.6
TYP. 7
–
–0.3 to +7
–10 to +60
Vcc –0.6
0.6
MAX. 6.5
MAX. 8
–0.3 to +7
–10 to +60
Vcc –0.6
0.6
MAX. 6.5
MAX. 8
–0.3 to +7
–40 to +85
Vcc –0.6
0.6
TYP. 5
MAX. 8
–0.3 to +7
–10 to +60
Vcc –0.6
0.6
MAX. 6.5
MAX. 8
–0.3 to +7
–10 to +60
Vcc –0.3
0.6
–
–
–0.3 to +7
–10 to +60
Vcc –0.3
0.6
MAX. 40
–
–0.3 to +7
–10 to +60
Vcc –0.3
0.6
MAX. 50
–
❇ PSD: Position Sensitive Detector
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
DISTANCE MEASURING SENSORS
✩New product
★Under development
■ Distance Measuring Sensors (2)
◆Analog Output (Including I2C output)
Distance
measuring
range
(cm)
★GP2Y0AF15 series
1.5 to 15
GP2Y0A51SK0F
Features
Vcc
(V)
Topr
(°C)
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
short measuring cycle (16.5 ms), compact,
lineup of various connector shapes
–0.3 to +7
–10 to +60
2 to 15
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
short measuring cycle (16.5 ms)
–0.3 to +7
–10 to +60
★GP2Y0AF30 series
4 to 30
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
short measuring cycle (16.5 ms), compact,
lineup of various connector shapes
–0.3 to +7
–10 to +60
GP2Y0A41SK0F
4 to 30
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
short measuring cycle (16.5 ms)
–0.3 to +7
–10 to +60
–0.3 to +3.6
–10 to +60
–0.3 to +3.6
–10 to +60
Infrared LED and CMOS image sensor with built-in
signal processing circuit, compact size
(18.9 × 8 × 5.2 mm), high-precision measurement,
analog output
Infrared LED and CMOS image sensor with built-in
signal processing circuit, compact size
(18.9 × 8 × 5.2 mm), high-precision measurement,
I2C output
✩GP2Y0E02A
4 to 50
✩GP2Y0E02B
4 to 50
✩GP2Y0E03
4 to 50
Infrared LED and CMOS image sensor with built-in
signal processing circuit, compact size
–0.3 to +5.5
(16.7 × 11 × 5.2 mm), high-precision measurement,
analog / I2C output both compatible
–10 to +60
10 to 80
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
linear voltage output
–0.3 to +7
–10 to +60
–0.3 to +5.5
–10 to +60
–0.3 to +7
–10 to +60
–0.3 to +7
–10 to +60
GP2Y0A21YK0F
*2
GP2Y0A60SZ0F/
GP2Y0A60SZLF
10 to 150
GP2Y0A02YK0F
20 to 150
GP2Y0A710K0F
100 to 550
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
compact type (22 x 8 x 7.2 mm),
long distance measuring type
(No external control signal required)
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
long distance measuring type
(No external control signal required)
Distance measuring sensor united with PSD ❇,
infrared LED and signal processing circuit,
long distance measuring type
(No external control signal required)
*1 Vcc = 5 V
*2 GP2Y0A60SZ0F: Surface mount type
GP2Y0A60SZLF: Board insertion type
*3 When Vcc = 3 V: Vo (TYP.) = 0.35 V (at L = 150 cm); ∆Vo (TYP.) = 1.6 V (at L = 150 cm → 20 cm)
Electro-optical characteristics*1
Dissipation
VOH
VOL
current
(V)
(V)
Operating
MIN.
MAX.
(mA)
VO (TYP.) = 0.4 V
(at L = 15 cm),
TYP. 17
∆VO (TYP.) = 2.3 V
(at L = 15 cm → 1.5 cm)
VO (TYP.) = 0.4 V
(at L = 15 cm),
TYP. 12
∆VO (TYP.) = 2.25 V
(at L = 15 cm → 2 cm)
VO (TYP.) = 0.4 V
(at L = 30 cm),
TYP. 17
∆VO (TYP.) = 2.3 V
(at L = 30 cm → 4 cm)
VO (TYP.) = 0.4 V
(at L = 30 cm),
MAX. 22
∆VO (TYP.) = 2.25 V
(at L = 30 cm → 4 cm)
VOUT (A) 1 = 0.3 to 0.8 V
(at L = 50 cm),
MAX. 36
VOUT (A) 3 = 2.1 to 2.3 V
(at L = 4 cm)
D1 = 45 to 50 cm
(at L = 50 cm),
MAX. 36
D3 = 3 to 5 cm
(at L = 4 cm)
VOUT (A) 1 = 0.3 to 0.8 V,
D1 = 45 to 50 cm
(at L = 50 cm),
MAX. 36
VOUT (A) 3 = 2.1 to 2.3 V,
D3 = 3 to 5 cm
(at L = 4 cm)
VO (TYP.) = 0.4 V
(at L = 80 cm),
MAX. 40
∆VO (TYP.) = 1.9 V
(at L: 80 cm → 10 cm)
VO (TYP.) = 0.65 V *3
(at L = 150 cm),
∆VO (TYP.) = 3.0 V
(at L = 150 cm → 20 cm)
VO (TYP.) = 0.4 V
(at L = 150 cm),
∆VO (TYP.) = 2.05 V
(at L = 150 cm → 20 cm)
VO (TYP.) = 2.5 V
(at L = 100 cm),
∆VO (TYP.) = 0.7 V
(at L = 100 cm → 200 cm)
Optoelectronics
Model No.
(Ta = 25°C)
Absolute maximum ratings
MAX. 50
MAX. 50
TYP. 30
❇ PSD: Position Sensitive Detector
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
73
DISTANCE MEASURING SENSORS / HIGH-PRECISION
DISPLACEMENT SENSOR / DUST SENSOR UNIT
OPTO
GP2Y5D91S00F
GP2Y0D805Z0F
GP2Y0D810Z0F,
GP2Y0D815Z0F,
GP2Y0D810Z1F
GP2Y0AF15 series
GP2Y0AF30 series
GP2Y0E02A
(GP2Y0E02B)
GP2Y0E03
GP2Y0A60SZ0F
GP2Y0A60SZLF
GP2Y0A21YK0F
GP2Y0A51SK0F
GP2Y0D02YK0F
(GP2Y0A02YK0F)
GP2Y0A710K0F
GP2Y0D21YK0F,
GP2Y0A41SK0F
GP2Y0D413K0F:
without mounting
hole
■ High-Precision Displacement Sensor
Model No.
GP2Y0AH01K0F
Topr
(°C)
Dissipation
current
(mA)
Distance
measuring
range (mm)
Distance characteristic of output
–10 to +60
4.5 to 5.5
TYP. 20
4.5 to 6.0
TYP. 1.70 V
Variation in output over range
(4.5 to 6.0 mm)
Features
Resolution: 50 µm
(Ta = 25°C)
Operating
supply voltage
(V)
GP2Y0AH01K0F
■ Dust Sensor Unit
(Ta = 25°C)
Model No.
Features
Topr
(°C)
GP2Y1010AU0F
Built-in infrared emitting diode,
photodiode and signal processing circuit,
compact, single-shot detection of house dust
–10 to +65
Electro-optical characteristics
Output voltage
Operating
Dissipation
Detection
at no dust
supply voltage
current
sensitivity
3
Voc (V)
(V)
(mA)
V/(0.1 mg/m )
4.5 to 5.5
TYP. 11
TYP. 0.5
TYP. 0.9
Output voltage
range
VOH (V)
MIN. 3.4
GP2Y1010AU0F
74
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
OPTO
FIBER OPTICS LINEUP FOR AUDIO EQUIPMENT
■ Fiber Optics Lineup for Audio Equipment
Type
Square connector
Fiber optic
transmitter
Outline
Without mounting
hole
Features
With shutter
Horizontal
mounting type
(EIAJ RC-5720B)
High speed signal
transmission
MAX. 13.2 Mb/s
MAX. 15.5 Mb/s
With mounting
hole
With shutter
Horizontal
mounting type
Model No.
Supply voltage
3 to 5 V
GP1FMV51TK0F
GP1FMV31TK0F
GP1FAV51TK0F*1
MAX. 13.2 Mb/s
MAX. 15.5 Mb/s
GP1FAV31TK0F
MAX. 50 Mb/s
Vertical
mounting type
Horizontal
mounting type
Without mounting
hole
With shutter
Horizontal
mounting type
With shutter
Horizontal
mounting type
Horizontal
mounting type
GP1FMV51RK0F
GP1FMV31RK0F
MAX. 13.2 Mb/s
MAX. 15.5 Mb/s
With protection
cap
GP1FAV50TK0F*1
GP1FAV30TK0F
MAX. 13.2 Mb/s
MAX. 15.5 Mb/s
With mounting
hole
GP1FSV51TK0F
GP1FSV31TK0F
(mounting height:
15 mm)
GP1FSB31TK0F
(mounting height:
8.5 mm)
MAX. 13.2 Mb/s
MAX. 15.5 Mb/s
Fiber optic
receiver
GP1FAV55TK0F
MAX. 13.2 Mb/s
MAX. 15.5 Mb/s
With protection
cap
GP1FAV51RK0F
GP1FAV31RK0F
MAX. 13.2 Mb/s
MAX. 15.5 Mb/s
Supply voltage
5V
Optoelectronics
Connector type
GP1FAV50RK0F
GP1FAV30RK0F
*1 TTL drive compatible
GP1FMV31 series
(GP1FMV51 series)
GP1FAV50TK0F
GP1FAV50RK0F,
GP1FAV30TK0F,
GP1FAV30RK0F
GP1FAV51TK0F
GP1FAV31TK0F,
GP1FAV55TK0F,
GP1FAV51RK0F,
GP1FAV31RK0F
GP1FSB31TK0F
GP1FSV31TK0F
(GP1FSV51TK0F)
75
FIBER OPTIC TRANSMITTERS (Square Connector) /
FIBER OPTIC RECEIVERS (Square Connector)
OPTO
■ Fiber Optic Transmitters (Square Connector)
Model No.
(Ta = 25°C)
Absolute maximum ratings
Appearance
Features
Mounting
Shutter
hole
Vcc
(V)
Topr
(°C)
Supply
voltage
(V)
Electro-optical characteristics
Propagation Dissipation Pulse Transmisdelay time
width sion speed
current
Icc
distortion
T
tPLH tPHL
(mA)
∆tw
(Mb/s)
(ns) (ns)
(ns)
MAX.
MAX. MAX. MAX.
GP1FMV31TK0F
No
Yes
Compact
–0.5 to +7
–20 to +70
2.7 to 5.25
180
180
12
±15
15.5
GP1FMV51TK0F
No
Yes
Compact
–0.5 to +7
–20 to +70
4.75 to 5.25
180
180
13
±15
13.2
–0.5 to +7
–20 to +70
2.7 to 5.25
180
180
12
±15
15.5
GP1FAV30TK0F▲
Yes
No
Low voltage drive,
with protection cap
GP1FAV50TK0F▲
Yes
No
TTL drive compatible,
with protection cap
–0.5 to +7
4.75 to 5.25
–20 to +70 Input voltage: 180
MIN. 2.0 V
180
13
±15
13.2
GP1FAV51TK0F
Yes
Yes
TTL drive compatible
–0.5 to +7
–20 to +70
4.75 to 5.25
180
180
13
±15
13.2
–0.5 to +7
–20 to +70
4.75 to 5.25
180
180
13
±15
13.2
GP1FSV51TK0F
No
Yes
Vertical mounting
(mounting height: 15 mm)
GP1FAV31TK0F
Yes
Yes
Low voltage drive
–0.5 to +7
–20 to +70
2.7 to 5.25
180
180
12
±15
15.5
–0.5 to +7
–20 to +70
2.7 to 5.25
180
180
13
±15
15.5
GP1FSV31TK0F
No
Yes
Vertical mounting
(mounting height: 15 mm)
GP1FAV55TK0F
Yes
Yes
High response speed
–0.5 to +7
–20 to +70
4.75 to 5.25
180
180
13
±15
50
Yes
Vertical mounting
(mounting height: 8.5 mm)
–0.5 to +7
–20 to +70
2.7 to 5.25
180
180
13
±15
15.5
GP1FSB31TK0F
No
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
■ Fiber Optic Receivers (Square Connector)
Appearance
Model No.
(Ta = 25°C)
Absolute maximum ratings
Features
Mounting
Shutter
hole
Vcc (V)
IOL
(mA)
Topr
(°C)
Supply
voltage
(V)
GP1FMV31RK0F
No
Yes
Compact, low voltage drive
–0.5 to +7 10 –20 to +70
180
180
15
±20
15.5
GP1FMV51RK0F
No
Yes
Compact
–0.5 to +7 10 –20 to +70 4.75 to 5.25 180
180
25
±20
13.2
–0.5 to +7 10 –20 to +70
180
180
15
±20
15.5
–0.5 to +7 10 –20 to +70 4.75 to 5.25 180
180
25
±20
13.2
–0.5 to +7 10 –20 to +70 4.75 to 5.25 180
180
25
±20
13.2
–0.5 to +7 10 –20 to +70
180
15
±20
15.5
GP1FAV30RK0F▲
Yes
No
Low voltage drive,
with protection cap
GP1FAV50RK0F▲
Yes
No
With protection cap
GP1FAV51RK0F
Yes
Yes
GP1FAV31RK0F
Yes
Yes
Low voltage drive
2.7 to 3.6
Electro-optical characteristics
Propagation Dissipation Pulse Transmisdelay time
width sion speed
current
Icc
distortion
T
tPLH tPHL
(mA)
∆tw
(Mb/s)
(ns) (ns)
(ns)
MAX.
MAX. MAX. MAX.
2.7 to 3.6
2.7 to 3.6
180
The model marked with ▲ may not be available in the near future. Contact with SHARP for details before use.
76
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
equipment using any SHARP devices shown in catalogs, data books, etc.
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
IR DETECTING UNIT FOR REMOTE CONTROL LINEUP
(CLASSIFIED BY FORM)
OPTO
■ IR Detecting Unit for Remote Control Lineup (Classified by Form)
Package
IR detecting unit
for remote control
Form
Detection
position*5
(from PCB)
Features
Operating voltage
Model No.
Compact, thin type
SMD (4.5 × 5.0 × 1.35 t mm)
3 to 5 V General type
GP1USC3xXP series
Compact type
SMD (6.8 × 2.1 × 2.35 t mm)
3 to 5 V
GP1UF31 series
3 to 5 V
GP1UE28XK0VF series
Lead L bend
with shield case
(holder)
16.0 mm*1
Compact size
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
12.0 mm*2
Compact size
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
6.8 mm*3
Compact size
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
Lead straight
with shield case
(holder)
19.0 mm
9.6 mm
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
Compact size
Compact size, Strengthened
resistance to electromagnetic
induction noise (Mesh type)
Holderless
Lead straight
6.0 mm
Lead L bend*4
5.3 mm
5V
GP1UM28XK0VF series
3 to 5 V General type
GP1UE28xXKC4 series
3 to 5 V
GP1UE28RK0VF series
5V
GP1UM28RK0VF series
3 to 5 V General type
GP1UE28xRKC4 series
3 to 5 V
GP1UE27XK0VF series
5V
GP1UM27XK0VF series
3 to 5 V General type
GP1UE27xXKC4 series
3 to 5 V
GP1UE27RK0VF series
5V
GP1UM27RK0VF series
3 to 5 V General type
GP1UE27xRKC4 series
3 to 5 V
GP1UE26XK0VF series
5V
GP1UM26XK0VF series
3 to 5 V General type
GP1UE26xXKC4 series
3 to 5 V
GP1UE26RK0VF series
5V
GP1UM26RK0VF series
3 to 5 V General type
GP1UE26xRKC4 series
3 to 5 V
GP1UE29QK0VF series
5V
GP1UM29QK0VF series
3 to 5 V General type
GP1UE29xQKC4 series
3 to 5 V
GP1UE28YK0VF series
5V
GP1UM28YK0VF series
3 to 5 V General type
GP1UE28xYKC4 series
3 to 5 V
GP1UE28QK0VF series
5V
GP1UM28QK0VF series
3 to 5 V General type
GP1UE28xQKC4 series
3 to 5 V
GP1UX31QS series
5V
GP1UX51QS series
3 to 5 V General type
GP1UXC4xQS series
3 to 5 V
GP1UX31RK series
5V
GP1UX51RK series
3 to 5 V General type
GP1UXC4xRK series
IR Devices
Type
*1 Mesh type (strengthened resistance to electromagnetic induction noise): 16.4 mm
*2 Mesh type: 12.4 mm
*3 Mesh type: 7.2 mm
*4 Mesh type: 5.3 mm
*5 Lead straight: Distance from lens center to mounting board upper surface
No mesh lead L bend: Distance from tip of lens to mounting board upper surface
Mesh-type lead L bend: Distance from tip of mesh to mounting board upper surface
77
OPTO
IR DETECTING UNITS FOR REMOTE CONTROL
■ IR Detecting Units for Remote Control
Absolute maximum ratings
Type
Surface-mount type,
Reflow soldering
compatible
With shield case (holder),
3 to 5 V drive (New type)
Series No.
GP1UF31xXP0F/ *5
GP1UF31xYP0F
0 to 6.0
Topr (°C)
Operating
voltage
(V)
–30 to +85 2.7 to 5.5
0.4
Vcc–0.5
Size (mm)
Terminal
layout
0.45
*4
6.8 × 2.1 × 2.35
–
5 × 4.5 × 1.3
–
GP1USC3xXP
0 to 6.0
–30 to +85 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
GP1UE26xXKC4
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.6 × 9.6 × 6.8
GP1UE27xXKC4
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.6 × 9.6 × 12.0
GP1UE28xXKC4
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.6 × 9.6 × 16.0
GP1UE28xYKC4
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.6 × 8.6 ×
12.5(9.6)*2
GP1UE26xRKC4
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.6 × 9.6 × 7.2
GP1UE27xRKC4
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.6 × 9.6 × 12.4
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.6 × 9.6 × 16.4
With shield case (holder),
3 to 5 V drive,
GP1UE28xRKC4
Strengthened resistance to
electromagnetic induction
GP1UE28xQKC4
noise (New type)
With shield case (holder),
5 V drive
Vcc (V)
(Ta = 25°C)
Electrical characteristics
VOL
fo
VOH
Icc
(V)
(V) (kHz)
(mA)*1
MIN.
MAX. TYP.
MAX.
5.6 × 9.0 ×
12.5(9.6)*2
5.6 × 16.2 ×
21.9(19)*2
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
GP1UE29xQKC4
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
GP1UM26XK0VF
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
5.6 × 9.6 × 6.8
5.6 × 9.6 × 12.0
GP1UM27XK0VF
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
GP1UM28XK0VF
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
5.6 × 9.6 × 16.0
GP1UM28YK0VF
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
5.6 × 8.6 ×
12.5(9.6)*2
GP1UM26RK0VF
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
5.6 × 9.6 × 7.2
5.6 × 9.6 × 12.4
5.6 × 9.6 × 16.4
GP1UM27RK0VF
With shield case (holder),
5 V drive,
GP1UM28RK0VF
Strengthened resistance to
electromagnetic induction
GP1UM28QK0VF
noise
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
GP1UM29QK0VF
0 to 6.0
–10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5
0.45
*3
GP1UE26XK0VF
0 to 6.0
–10 to +70 2.7 to 5.5
0.45
*3
5.6 × 9.6 × 6.8
5.6 × 9.6 × 12.0
With shield case (holder),
3 to 5 V drive
0.4
Vcc–0.5
5.6 × 9.0 ×
12.5(9.6)*2
5.6 × 16.2 ×
21.9(19)*2
GP1UE27XK0VF
0 to 6.0
–10 to +70 2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
GP1UE28XK0VF
0 to 6.0
–10 to +70 2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
5.6 × 9.6 × 16.0
GP1UE28YK0VF
0 to 6.0
–10 to +70 2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
5.6 × 8.6 ×
12.5(9.6)*2
GP1UE26RK0VF
0 to 6.0
–10 to +70 2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
5.6 × 9.6 × 7.2
5.6 × 9.6 × 12.4
5.6 × 9.6 × 16.4
GP1UE27RK0VF
With shield case (holder),
3 to 5 V drive,
GP1UE28RK0VF
Strengthened resistance to
electromagnetic induction
GP1UE28QK0VF
noise
0 to 6.0
–10 to +70 2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
0 to 6.0
–10 to +70 2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
0 to 6.0
–10 to +70 2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
GP1UE29QK0VF
0 to 6.0
–10 to +70 2.7 to 5.5
0.4
Vcc–0.5
0.45
*3
GP1UXC4xQS
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.5 × 5.3 × 7.5
GP1UXC4xRK
0 to 6.0
–10 to +70 2.7 to 5.5
0.6
Vcc–0.5
0.45
*3
5.5 × 5.3 × 7.5
GP1UX51QS
0 to 6.0
–10 to +70 4.5 to 5.5
0.6
Vcc–0.5
0.45
*3
5.5 × 5.3 × 7.5
GP1UX51RK
0 to 6.0
–10 to +70 4.5 to 5.5
0.6
Vcc–0.5
0.45
*3
5.5 × 5.3 × 7.5
GP1UX31QS
0 to 6.0
–10 to +70 4.5 to 5.5
0.4
Vcc–0.5
0.45
*3
5.5 × 5.3 × 7.5
GP1UX31RK
0 to 6.0
–10 to +70 4.5 to 5.5
0.4
Vcc–0.5
0.45
*3
5.5 × 5.3 × 7.5
Holderless, 3 to 5 V drive,
Strengthened resistance to
electromagnetic induction
noise (New type)
Holderless, 5 V drive,
Strengthened resistance to
electromagnetic induction
noise
Holderless, 3 to 5 V drive,
Strengthened resistance to
electromagnetic induction
noise
Center
Vcc
5.6 × 9.0 ×
12.5(9.6)*2
5.6 × 16.2 ×
21.9(19)*2
Center
GND
* A voltage regulator circuit is built-in but may be affected by the usage environment. Install with an externally mounted C and R as a power supply filter.
*1 When no signal is input (during input light).
*2 Figures in parentheses indicate the distance to the light detection center.
*3 fo = 32.75/36/36.7/38/40 kHz
Notice
*4 fo = 36/36.7/38/40 kHz
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in
*5 GP1UF31xXP0F: Top view taped package,
equipment using any SHARP devices shown in catalogs, data books, etc.
GP1UF31xYP0F: Side view taped package
Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
78
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants
(PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.