GP1S094HCZ

GP1S094HCZ GP1S094HCZ Subminiature, Wide gap, Transmissive Type Photointerrupter ■ Features ■ Outline Dimensions 1. General purpose 2. Wide gap (Gap width:3.0mm) 3. Slit width (Detector side):0.3mm (Unit : mm) Internal connection diagram Top View 1 a' 2 1 2 3 a-a' section +0.2 0.15−0.1 ∗4.55 3 2 +0 φ1.0−0.1 4 1 (0.3)Slit width 4.8 3.0±0.2 C0.2 0.75 Unit mA V mW V V mA mW mW °C °C °C (C0.3) ∗∗ +0.3 3.1−0.2 ∗∗ (Ta=25°C) ±0.05 Rating 50 6 75 35 6 20 75 100 −25 to +85 −40 to +100 260 2.6 Center of light axis 3.0 Symbol IF VR P VCEO VECO IC PC Ptot Topr Tstg Tsol 4 (C0.4) 0.8 ■ Absolute Maximum Ratings 4 3 5.5 3.0 (0.75) 1. Cameras 2. CD-ROM drives 2. DVD-ROM drives 3. VCR Parameter Forward current Input Reverse voltage Power dissipation Collector-emitter voltage Emitter-collector voltage Output Collector current Collector power dissipation Total power dissipation Operating temperature Storage temperature *1 Soldering temperature (C0.3) a ■ Applications Anode Collector Emitter Cathode ∗2.0 0.4 0.5 (0.05) ∗∗∗ ❈ Unspecified tolerance : ±0.2mm ❈ ( ) : Reference dimensions ❈ The dimensions indicated by ∗refer to those measured from the lead base. ❈ Burr’s dimensions : 0.15MAX. ❈ The lead may be exposed at the shaded portion. (∗∗) ❈ This portion has no solder plating. (∗∗∗) *1 For MAX. 5s Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://sharp-world.com/ecg/ GP1S094HCZ ■ Electro-optical Characteristics Parameter Forward voltage Input Reverse current Output Collector dark current Collector current Transfer Collector-emitter saturation voltage characteRise time ristics Response time Fall time Symbol Conditions IF=20mA VR=3V VCE=20V IF=5mA, VCE=5V IF=10mA, IC=40µA IC=100µA, VCE=5V, RL=1kΩ VF IR ICEO IC VCE(sat) tr tf ■ Test Circuit for Response Time VCC RD Input RL Output Input Output 10% 90% tr tf MIN. − − − 40 − − − TYP. 1.2 − − − − 50 50 MAX. 1.4 10 100 400 0.4 150 150 (Ta=25°C) Unit V µA nA µA V µs µs NOTICE ● The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. ● Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. ● Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: - - - Personal computers - -- Office automation equipment - -- Telecommunication equipment [terminal] - - - Test and measurement equipment - - - Industrial control - -- Audio visual equipment - -- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: - -- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) - - - Traffic signals - - - Gas leakage sensor breakers - - - Alarm equipment - -- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: - - - Space applications - -- Telecommunication equipment [trunk lines] - -- Nuclear power control equipment - -- Medical and other life support equipment (e.g., scuba). ● Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. ● If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. ● This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. ● Contact and consult with a SHARP representative if there are any questions about the contents of this publication.