GP1S096HCZ

Under development New product GP1S096HCZ Photointerrupter Subminiature, Low height, Transmissive Type Photointerrupter a' Outline Dimensions a (C 0.3) a-a' section 3.5 1.0 Center of light access (0.3)Slit width (C0.3) 3.5±0.5 Applications (1) Cameras (2) CD-ROM drives (3) DVD-ROM drives (4) VCR 2.6 2.9 (C 0.4) 2.1 (0.75) Features (1) General purpose (2) Wide gap(Gap width: 1.0mm) (3) Low height(Height: 2.9mm) (4) Slit width(Detector side): 0.3mm *2.55 3 0.15 0.4 *2.0 +0.2 –0.1 4 Internal connection diagram 2 1 1 2 1 2 3 3 4 4 Anode Collector Emitter Cathode The dimensions indicated by * refer to those measured from the lead base. Absolute Maximum Ratings Input Output *1 Parameter Forward current Reverse voltage Power dissipation Collector-emitter voltage Emitter-collector voltage Collector current Collector power dissipation Total power dissipation Operating temperature Storage temperature Soldering temperature (Ta=25˚C) Symbol IF VR P VCEO VECO IC PC Ptot Topr Tstg Tsol Rating 50 6 75 35 6 20 75 100 –25 to +85 –40 to +100 260 Unit mA V mW V V mA mW mW ˚C ˚C ˚C *1 For 5s (Notice) •In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. •Specifications are subject to change without notice for improvement. (Internet) •Data for Sharp's optoelectronic/power devices is provided on internet. (Address http://www.sharp.co.jp/ecg/) Tec.GP000301-A GP1S096HCZ Photointerrupter Electro-optical Characteristics (Ta=25˚C) Parameter Symbol Conditions VF IF=20mA Forward voltage Input VR=3V IR Reverse current VCE=20V ICEO Output Collector dark current IF=5mA, VCE=5V Collector current IC Transfer Collector-emitter saturation votlage VCE(sat) IF=10mA, IC=40µA characteristics tr Rise time IC=100µA, VCE=5V, RL=1kΩ Response time tf Fall time MIN. – – – 100 – – – TYP. 1.2 – – – – 50 50 MAX. 1.4 10 100 400 0.4 150 150 Unit V µA nA µA V µs µs Measuring Circuit of Response Time Input VCC RD RL Output 10% Output 90% tr tf As of August 2000 Tec.GP000301-A Application Circuits NOTICE ●The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. ●Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. ●Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). ●Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. ●If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. ●This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. ●Contact and consult with a SHARP representative if there are any questions about the contents of this publication. 115