GW5DGA40M04

Spec No. Issue DG-10Y033B 22-Feb-11 S P E C I F I C A T I O N S Product Type ZENIGATA LED Model No. GW5DGA**M04 ** ： 27, 30, 35, 40, 50, 65 ※These specifications contain 20 pages including the cover and appendix. If you have any objections, please contact us before issuing purchasing order. CUSTOMERS ACCEPTANCE Reference DATE: BY: PRESENTED BY: Y. Ohiwane Dept. General Manager REVIEWED BY: PREPARED BY: Development DepartmentⅡ System Device Division Ⅲ Electronic Components And Devices Group SHARP CORPORATION Model No. GW5DGA**M04 ● Handle this document carefully for it contains material protected by international copyright law. Any reproduction, full or in part, of this material is prohibited without the express written permission of the company. ● When using the products covered herein, please observe the conditions written herein and the precautions outlined in the following paragraphs. In no event shall the company be liable for any damages resulting form failure to strictly adhere to these conditions and precautions. (1) Please do verify the validity of this part after assembling it in customer’s products, when customer wants to make catalogue and instruction manual based on the specification sheet of this part. (2) The products covered herein are designed and manufactured for the following application areas. When using the products covered herein for the equipment listed in paragraph (3), even for the following application areas, be sure to observe the precautions given in Paragraph (3). Never use the products for the equipment listed in Paragraph (4). ･Office electronics ･Instrumentation and measuring equipment ･Machine tools ･Audiovisual equipment ･Home appliances ･Communication equipment other than for trunk lines (3) These contemplating using the products covered herein for the following equipment which demands high reliability, should first contact a sales representative of the company and then accept responsibility for incorporating into the design fail-safe operation, redundancy, and other appropriate measures for ensuring reliability and safety of the equipment and the overall system. ･Control and safety devices for airplanes, trains, automobiles, and other transportation equipment ･Mainframe computers ･traffic control systems ･Gas leak detectors and automatic cutoff devices ･Rescue and security equipment ･Other safety devices and safety equipment, etc. (4) Do not use the products covered herein for the following equipment which demands extremely high performance in terms of functionality, reliability, or accuracy. ･Aerospace equipment ･Communications equipment for trunk lines ･Control equipment for the nuclear power industry ･Medical equipment related to life support, etc. (5) please direct all queries and comments regarding the interpretation of the above four Paragraphs to a sales representative of the company. ● Please direct all queries regarding the products covered herein to a sales representative of the company. DG-10Y033B Model No. Page GW5DGA**M04 1 of 18 GW5DGA**M04 specifications 1. Application These specifications apply to the light emitting diode module Model No. GW5DGA**M04. [ LED module (InGaN Blue LED chip + Phosphor) ] Main application : Lighting 2. External dimensions and equivalent circuit -------------------------------- Refer to Page 2. 3. Ratings and characteristics --------------------------------------------------- Refer to Page 3 - 5. 3-1. Absolute maximum ratings 3-2. Electro-optical characteristics 3-3. Derating curve 4. Reliability ---------------------------------------------------------------------- Refer to Page 6. 4-1. Test items and test conditions 4-2. Failure criteria 5. Quality level ------------------------------------------------------------------- Refer to Page 7. 5-1. Applied standard 5-2. Sampling inspection 5-3. Inspection items and defect criteria 6. Supplements------------------------------------------------------------------- Refer to Page 8 - 14. 6-1. Chromaticity rank table 6-2. Packing 6-3. Label 6-4. Indication printed on product 7. Precautions -------------------------------------------------------------------- Refer to Page 15 - 17. 8. Characteristics diagram (TYP.) ---------------------------------------------- Refer to Page 18. DG-10Y033B Model No. Page GW5DGA**M04 2 of 18 2. External dimensions and equivalent circuit Unit = mm 24.0 + 0.50 / - 0.10　① ( 18.6 ) Top view ( R8.6 ) 20.0 ( 12.5 ) + 0.50 / - 0.10 ② Side view 1.0 ( 1.8 ) ± 0.1 (Note) Values inside parentheses are reference values. External dimension of ceramic substrate is the indication of maximum length at each side. Equivalent circuit R R + connection terminal - connection terminal (Note) 12 series × 8 parallel = 96 pcs of LEDs Unit Material Drawing No. mm Substrate : Alumina Ceramic 52211021 DG-10Y033B Model No. Page GW5DGA**M04 3 of 18 3. Ratings and characteristics 3-1. Absolute maximum ratings Item Power Dissipation *1,4 Forward Current *1,4 Reverse Voltage *2,4 Operating Temperature *3 Storage Temperature Symbol P IF VR Topr Tstg Rating 20 500 -15 - 30 ～ + 100 - 40 ～ + 100 Unit W mA V ℃ ℃ *1 Power dissipation and forward current are the value when the module temperature is set lower than the rating by using an adequate heat sink. *2 Voltage resistible at initial connection error (Not dealing with the possibility of always-on reverse voltage.) *3 Case temperature Tc (Refer to measuring point for case temperature in the next page.) Refer to "Derating curve" in the next page as for operating current. *4 Tc = 25 ℃ DG-10Y033B Model No. Page GW5DGA**M04 4 of 18 3-2. Electro-optical characteristics Item ** common Forward Voltage *5 Luminous Flux *6 27 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 30 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 35 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 40 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 50 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Luminous Flux *6 65 Chromaticity Coordinates *7 Color Temperature General Color Rendering Index *8 Symbol VF Ф x y Ra Ф x y Ra Ф x y Ra Ф x y Ra Ф x y Ra Ф x y Ra Condition IF = 400 mA IF = 400 mA IF = 400 mA IF = 400 mA IF = 400 mA IF = 400 mA IF = 400 mA MIN. 34 1000 (2600) 90 1020 (2900) 90 1050 (3300) 90 1080 (3900) 90 1100 (4745) 1100 (6020) - TYP. 37 (1150) (0.464) (0.418) (2700) (93) (1170) (0.435) (0.403) (3025) (93) (1200) (0.409) (0.393) (3450) (93) (1230) (0.381) (0.383) (4050) (92) (1250) (0.346) (0.360) (5000) (90) (1250) (0.313) (0.332) (6500) (90) (Tc = 25 ℃) MAX. Unit 40 V lm K (2800) lm K (3150) lm K (3600) lm K (4200) lm K (5311) lm K (7040) - (Note) Values inside parentheses are shown for reference purpose only. *5 (After 20 ms drive, Measurement tolerance: ± 3 %) *6 Monitored by Sharp's 8 inch integrating sphere and Otsuka electronics MCPD-LE3400 (After 20 ms drive, Measurement tolerance: ± 20 %) *7 Monitored by Sharp's 8 inch integrating sphere and Otsuka electronics MCPD-LE3400 (After 20 ms drive, Measurement tolerance: ± 0.01) *8 Monitored by Sharp's 8 inch integrating sphere and Otsuka electronics MCPD-LE3400 (After 20 ms drive, Measurement tolerance: ± 4) DG-10Y033B Model No. Page GW5DGA**M04 5 of 18 3-3. Derating curve Forward Current Derating Curve 600 Forward Current I F [mA] 500 400 300 200 100 0 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 Case Temperature T c [℃] (Note) To keep the case temperature lower than the rating, enough heat-radiation performance needs to be secured by using an adequate heat sink. For soldering connection, please evaluate in your circumstance to make sure soldering reliability. ( Above derating curve is specified to LED device, not for soldering connection ) And please consider to avoid physical stress between wire and substrate, and some protection like silicon bond on top of soldered wire is recommended. Please ensure the maintenance of heat radiation not to exceed case temperature over the rating in operation. （Measuring point for case temperature ） measuring point DG-10Y033B Model No. Page GW5DGA**M04 6 of 18 4. Reliability 　　The reliability of products shall be satisfied with items listed below. 4-1. Test items and test conditions No. Test item 1 2 3 4 5 6 7 Temperature Cycle Confidence level: 90 % Samples Defective LTPD n C (%) Test conditions - 40 ℃(30 min) ～ + 100 ℃(30 min), 100 cycles 11 0 20 11 0 20 11 0 20 11 0 20 11 0 20 5 0 50 5 0 50 Tstg = + 60 ℃, RH = 90 %, Time = 1000 h Temperature Humidity Storage High Temperature Storage Low Temperature Storage Steady State Operating Life Shock Acceleration: 15000 m/s , Pulse width: 0.5 ms Vibration Direction: 3 directions (X, Y and Z) 3 trials in each direction Frequency: 100 to 2000 Hz for 4 minutes per trial Tstg = + 100℃, Time = 1000 h Tstg = - 40 ℃, Time = 1000 h Tc = 60 ℃, IF = 450 mA, Time = 1000 h 2 2 Acceleration: 200 m/s Direction: 3 directions (X, Y and Z) 4 trials in each direction 4-2. Failure criteria No. Parameter 1 Forward Voltage 2 Luminous Flux Symbol VF Ф Failure criteria VF ＞ Initial value × 1.1 Ф＜ Initial value × 0.7 DG-10Y033B Model No. Page GW5DGA**M04 7 of 18 5. Quality level 5-1. Applied standard ISO2859-1 5-2. Sampling inspection A single normal sampling plan, level S-4. 5-3. Inspection items and defect criteria No. Item No light emitting 1 No radiation 2 3 4 Electro-optical characteristics External dimensions Appearance Defect criteria Classification AQL Major defect 0.1% Minor defect 0.4% Not conforming to the specification (Forward voltage, Luminous flux and Chromaticity) Not conforming to the specified dimensions (External dimensions of ① and ② shown in Page 2) Nonconformity observed in product appearance is determined as defective only when electro-optical characteristics is affected by. ■Foreign material, scratch, or bubble at emitting area: 0.8 mm φ ■Fiber generation at emitting area: 0.2 mm in width and 2.5 mm in length ■Foreign material at connection terminal: 0.8 mm φ ■Substrate burr on edge: Over dimension tolerance (Note) Products with removable foreign material attached on is not determined to be defective. DG-10Y033B Model No. Page GW5DGA**M04 8 of 18 6. Supplements (Tolerance: x,y ± 0.005 ） （IF = 400 mA, T c = 25 ℃） 6-1. Chromaticity rank table **： ： 27 x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4606 0.4526 0.4669 0.4756 0.4250 0.4100 0.4100 0.4250 x y x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4606 0.4526 0.4595 0.4679 0.4250 0.4100 0.4100 0.4250 0.4679 0.4595 0.4669 0.4756 0.4250 0.4100 0.4100 0.4250 Range Rank 1 2 * The percentage of each rank in the shipment shall be determined by SHARP. Chromaticity Diagram 0.440 y 0.430 0.420 1 2 0.410 2800K 0.400 0.440 0.450 2700K 0.460 x 2600K 0.470 0.480 DG-10Y033B Model No. Page GW5DGA**M04 9 of 18 (Tolerance: x,y ± 0.005 ） （IF = 400 mA, T c = 25 ℃） **： ： 30 x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4310 0.4243 0.4384 0.4460 0.4100 0.3950 0.3950 0.4100 x y x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4310 0.4243 0.4311 0.4383 0.4100 0.3950 0.3950 0.4100 0.4383 0.4311 0.4384 0.4460 0.4100 0.3950 0.3950 0.4100 Range Rank 1 2 * The percentage of each rank in the shipment shall be determined by SHARP. Chromaticity Diagram 0.420 0.410 y 1 2 0.400 3100K 3000K 2900K 0.390 0.380 0.410 0.420 0.430 x 0.440 0.450 DG-10Y033B Model No. Page GW5DGA**M04 10 of 18 (Tolerance: x,y ± 0.005 ） （IF = 400 mA, T c = 25 ℃） **： ： 35 x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4041 0.3988 0.4124 0.4186 0.4000 0.3850 0.3850 0.4000 x y x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.4041 0.3988 0.4054 0.4112 0.4000 0.3850 0.3850 0.4000 0.4112 0.4054 0.4124 0.4186 0.4000 0.3850 0.3850 0.4000 Range Rank 1 2 * The percentage of each rank in the shipment shall be determined by SHARP. Chromaticity Diagram 0.410 0.400 y 1 2 0.390 3600K 3500K 3400K 3300K 0.380 0.370 0.390 0.400 0.410 x 0.420 0.430 DG-10Y033B Model No. Page GW5DGA**M04 11 of 18 (Tolerance: x,y ± 0.005 ） （IF = 400 mA, T c = 25 ℃） **： ： 40 x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3762 0.3718 0.3837 0.3895 0.3890 0.3700 0.3750 0.3950 x y x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3762 0.3718 0.3775 0.3826 0.3890 0.3700 0.3724 0.3919 0.3826 0.3775 0.3837 0.3895 0.3919 0.3724 0.3750 0.3950 Range Rank 1 2 * The percentage of each rank in the shipment shall be determined by SHARP. Chromaticity Diagram 0.400 0.390 y 2 1 0.380 0.370 3900K 4000K 4100K 4200K 0.360 0.360 0.370 0.380 x 0.390 0.400 DG-10Y033B Model No. Page GW5DGA**M04 12 of 18 (Tolerance: x,y ± 0.005 ） （IF = 400 mA, T c = 25 ℃） **： ： 50 x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3376 0.3369 0.3524 0.3551 0.3616 0.3431 0.3555 0.3760 x y x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3376 0.3369 0.3446 0.3464 0.3616 0.3431 0.3493 0.3688 0.3464 0.3446 0.3524 0.3551 0.3688 0.3493 0.3555 0.3760 Range Rank 1 2 * The percentage of each rank in the shipment shall be determined by SHARP. Chromaticity Diagram 0.380 0.370 y 2 0.360 1 0.350 4800K 5000K 5200K 0.340 0.320 0.330 0.340 x 0.350 0.360 DG-10Y033B Model No. Page GW5DGA**M04 13 of 18 (Tolerance: x,y ± 0.005 ） （IF = 400 mA, T c = 25 ℃） **： ： 65 x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3028 0.3058 0.3217 0.3205 0.3304 0.3161 0.3316 0.3481 x y x y Chromaticity coordinates Point 1 Point 2 Point 3 Point 4 0.3028 0.3058 0.3138 0.3117 0.3304 0.3161 0.3238 0.3393 0.3117 0.3138 0.3217 0.3205 0.3393 0.3238 0.3316 0.3481 Range Rank 1 2 * The percentage of each rank in the shipment shall be determined by SHARP. Chromaticity Diagram 0.350 0.340 y 2 0.330 1 6000K 0.320 6400K 6800K 0.310 0.290 0.300 0.310 x 0.320 0.330 DG-10Y033B Page Model No. GW5DGA**M04 14 of 18 6-2. Packing ■ One tray composed of 40 pieces ■ 5 trays (200 piecies) and one upper lid-tray in one moisture-proof bag ■ 2 bags (400 pieces) in one carton ■ Dimensions of outer carton: 235 × 220 × 90 mm (Reference value) (Note 1) There are cases of one carton composed of one bag. (200 pieces) (Note 2) State of packing is subject to change. ＜Outer carton＞ ＜One bag＞ 200 pieces × 2 bags = 400 pieces ＜One tray＞ 　 40 pieces × 5 trays = 200 pieces 5 × 8 ＝ 40 pieces (225mm) 6-3. Label Following label is attached on moisture-proof bags. (210mm) 1) Lot No. indication ５ ０ １ １ Ｇ ０ １ ０ ０ １ Ａ ① SHIPMENT TABLE PART No. GW5DGA**M04 ← Model number ← Quantity and rank ← Lot No. ← Bar code ← Production country (GW5DGA**M04M) 200 RANK 1 5011G01001A QUANTITY. LOT No. CORPORATION MADE IN PHILIPPINES SHARP R.C SHARP LABEL ② ③ ④ ⑤ ⑥ ⑦ ① Production plant code ② Shipping year （Year last digit ） ③ Shipping month （1～9 or O, N, D ） ④ Fixed code G ⑤ Shipping date （01～31） ⑥ Serial No. ⑦ Fixed code A 6-4. Indication printed on product 　 Model No. and control No. are indicated on substrate surface. 1) Model No. Abbreviated Model No. " 5DGA**M04 " is indicated. 2) Control No. Indicated as follows; Ｍ １ １ Ａ ０ １ － 1 ① ② ③ ④ ⑤ ① Production plant code (to be indicated alphabetically) ② Year of production (the last two figures of the year) Model No. ③ Month of production 　(to be indicated alphabetically with January corresponding to A) ④ Date of production (01～31) ⑤ Rank: Chromaticity rank is indicated as follows; Rank １ → １ Control No. DG-10Y033B Model No. Page GW5DGA**M04 15 of 18 7. Precautions ① Storage conditions Please follow the conditions below. ・Before opened: Temperature 5 ～ 30 ℃, Relative humidity less than 60 %. (Before opened LED should be used within a year) ・After opened: Temperature 5 ～ 30 ℃, Relative humidity less than 60 %. (Please apply soldering within 1 week) ・After opened LED should be kept in an aluminum moisture proof bag with a moisture absorbent material (silica gel). ・Avoid exposing to air with corrosive gas. If exposed, electrode surface would be damaged, which may affect soldering. ② Usage conditions This product is not designed for the use under any of the following conditions. Please confirm performance and reliability well enough if you use under any of the following conditions; ・In a place with a lot of moisture, dew condensation, briny air, and corrosive gas. (Cl, H 2S, NH3, SO2, NOX, etc.) ・Under the direct sunlight, outdoor exposure, and in a dusty place. ・In water, oil, medical fluid, and organic solvent. ③ Heat radiation If forward current (I F) is applied to single-state module at any current, there is a risk of damaging LED or emitting smoke. Equip with specified heat radiator, and avoid heat stuffed inside the module. ④ Installation Material of board is alumina ceramic. If installed inappropriately, trouble of no radiation may occur due to board crack or overheat. Please take particular notice for installation. Refer to the following cautions on installation. ・ Apply thermolysis adhesive, adhesive sheet or peculiar connector when mounted on heat radiator. In case of applying adhesive or adhesive sheet only, check the effectiveness and reliability before fixing. If LED comes off from heat radiator, unusual temperature rise entails hazardous phenomena including device deterioration, coming off of solder at leads, and emitting smoke. ・ When LED device is mechanically fixed or locked, Please take into consideration regarding the method of attachment due to fail from stress. ・ Avoid convexly uneven boards. Convex board is subject to substrate cracking or debasement of heat release. ・ It is recommended to apply adhesive or adhesive sheet with high thermal conductivity for radiation of heat effectively. ・ Please take care about the influence of color change of adhesive or adhesive sheet in initial and long term period, which may affect light output or color due to change of reflectance from backside. DG-10Y033B Model No. Page GW5DGA**M04 16 of 18 ・ Do not touch resin part including white resin part on the surface of LED. No light emission may occur due to damage of resin or cutting wire of LEDs by outer force. When using tweezers, please handle by ceramic substrate part and avoid touching resin part. For mounting, please handle by side part of ceramic or the specified area shown below. Handling area ⑤ Connecting method In case of solder connecting method, follow the conditions mentioned below. ・Use Soldering iron with thermo controller (tip temperature 380 ℃), within 5 seconds per one place. ・Secure the solderwettability on whole solder pad and leads. ・During the soldering process, put the ceramic board on materials whose conductivity is poor enough not to radiate heat of soldering. ・Warm up (with using a heated plate) the substrate is recommended before soldering. ( preheat condition: 100 ℃ ～ 150 ℃, within 60 sec ) ・Avoid touching a part of resin with soldering iron. ・This product is not designed for reflow and flow soldering. ・Avoid such lead arrangement as applying stress to solder-applied area. ・Please do not detach solder and make re-solder. ・Please solder evenly on each electrodes. ・Please prevent flux from touching to resin. ⑥ Static electricity This product is subject to static electricity, so take measures to cope with it. Install circuit protection device to drive circuit, if necessary. ⑦ Drive method ・Any reverse voltage cannot be applied to LEDs when they are in operation or not. Design a circuit so that any flow of reverse or forward voltage can not be applied to LEDs when they are out of operation. ・Module is composed of LEDs connected in both series and parallel. Constant voltage power supply runs off more than specified current amount due to lowered V F caused by temperature rise. Constant current power supply is recommended to drive. ⑧ Cleaning Avoid cleaning, since silicone resin is eroded by cleaning. ⑨ Color-tone variation Chromaticity of this product is monitored by integrating sphere right after the operation. Chromaticity varies depending on measuring method, light spread condition, or ambient temperature. Please verify your actual conditions before use. DG-10Y033B Model No. Page GW5DGA**M04 17 of 18 ⑩ Safety ･Please prevent to see lighting LED devices directly at any moment for safety your eyes. ･Looking light from LEDs for a long time may result in hurt your eyes. ･In case that excess current (over ratings) are supplied to the device, hazardous phenomena including abnormal heat generation, emitting smoke, or catching fire can be caused. Take appropriate measures to excess current and voltage. ・In case of solder connecting method, there is a possibility of fatigue failure by heat. Please fix the leads in such case to protect from short circuit or leakage of electricity caused by contact. ・Please confirm the safety standards or regulations of application devices. ・Please careful not to injure your hand by edge of ceramic substrate. ⑪ Other cautions Guarantee covers the compliance to the quality standards mentioned in the Specifications, however it does not cover the compatibility with application of the end-use, including assembly and usage environment. In case any quality problems occurred in the application of end-use, details will be separately discussed and determined between the parties hereto. DG-10Y033B Model No. Page GW5DGA**M04 18 of 18 8. Characteristics diagram (TYP.) Forward Voltage vs. Forward Current Forward Current vs. Relative Luminous Flux Tc = 25 ℃ 500 100 400 Forward Current IF [mA] Relative Luminous Flux [%] Tc = 25 ℃ 120 80 60 40 20 300 200 100 0 0 0 100 200 300 400 500 30 Forward Current IF [mA] 31 32 33 34 35 36 Case Temperature vs. Relative Luminous Flux 38 Case Temperature vs. Forward Voltage IF = 400 mA IF = 400 mA 120 42 100 40 Forward Voltage VF [V] Relative Luminous Flux [%] 37 Forward Voltage VF [V] 80 60 40 20 38 36 34 32 0 0 30 60 Case Temperature Tc [℃] 90 0 30 60 Case Temperature Tc [℃] (Note) Characteristics data shown here are for reference purpose only. (Not guaranteed data) 90