LD-17Y60

No. DATE LD – 17Y60 November．25．2005 TECHNICAL LITERATURE FOR TFT - LCD module These parts have corresponded with the RoHS directive. MODEL No. LQ150X1LGN2E is subject or its to change without before notice. designing The So, your technical please literature contact based SHARP on this representative product literature. Engineering department Ⅳ Mobile LCD design center Ⅰ MOBILE LIQUID CRYSTAL DISPLY GROUP SHARP CORPORATION RECORDS OF REVISION LQ104V1DG61 SPEC No. DATE REVISED SUMMARY PAGE - NOTE No. LD-17Y60 Nov.25.2005 - 1 st Issue LD-17Y60-1 1. Application This technical literature applies to the color 15.0 XGA TFT-LCD module LQ150X1LGN2E. ◎ These technical literature sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. ◎The device listed in these technical literature sheets was designed and manufactured for use in general electronic equipment. ◎In case of using the device for applications such as control and safety equipment for transportation (conrrols of aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken. ◎Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment for life support. ◎SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. ◎Contact and consult with a SHARP sales representative for any questions about this device. 2. Overview (Thin Film Transistor). This module is a color active matrix LCD module incorporating amorphous silicon TFT It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit. Graphics and texts can be displayed on a 1024×RGB×768 dots panel with about 16 million colors by using LVDS (Low Voltage Differential Signaling) and supplying +3.3V DC supply voltages for TFT-LCD panel driving and supply voltage for backlight. LD-17Y60-2 3. Mechanical Specifications Parameter Display size Specifications 38 (Diagonal) 15.0 (Diagonal) Active area Pixel format 304.1 (H)×228.1 (V) 1024 (H)×768 (V) (1 pixel＝R+G+B dots) Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment 0.297 (H)×0.297 (V) R, G, B vertical stripe Normally white 326.0(W)×252.0(H)×11.5(D) 1100 (MAX) mm g mm Unit cm Inch mm Pixel Anti-glare and hard-coating 2H (Haze value = 28) *1.Note: excluding back light cables, cover and pet sheet. The thickness of module (D) doesn’t contain the projection. Outline dimensions are shown in Fig.1. LD-17Y60-3 4. Input Terminals 4-1. TFT-LCD panel driving CN1 (Interface signals and +3.3V DC power supply) Using connectors ：DF14H-20P-1.25H (Hirose Electric Co., Ltd.) Corresponding connectors ：DF14-20S-1.25C(Connector) DF14-2628SCFA(Terminal) Corresponding LVDS Transmitter ：THC63LVDM83R(Thine) or compatible Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol Vcc Vcc GND GND RXIN0RXIN0+ GND RXIN1RXIN1+ GND RXIN2RXIN2+ GND RXCKINRXCKIN+ GND RXIN3RXIN3+ GND LVDS_SET Function +3.3V Power supply +3.3V Power supply Remark Receiver signal (-) Receiver signal (+) Receiver signal (-) Receiver signal (+) Receiver signal (-) Receiver signal (+) Clock signal (-) Clock signal (+) Receiver signal (-) Receiver signal (+) LVDS_SET LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS 【note1】 LD-17Y60-4 4-2 Data Mapping 1) 8 bit input 【note1】pin assignment with LVDS_SET pin (Thine:THC63LVDM83R) Transmitter Pin No 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 50 2 8 10 16 18 25 Data TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 TD0 TD1 TD2 TD3 TD4 TD5 TD6 20pin =L (GND) or Open R2 R3 R4 R5 R6 R7 (MSB) G2 G3 G4 G5 G6 G7 (MSB) B2 B3 B4 B5 B6 B7 (MSB) (NA) (NA) DE R0 (LSB) R1 G0 (LSB) G1 B0 (LSB) B1 (NA) LVDS_SET =H (3.3V) R0 (LSB) R1 R2 R3 R4 R5 G0 (LSB) G1 G2 G3 G4 G5 B0 (LSB) B1 B2 B3 B4 B5 (NA) (NA) DE R6 R7 (MSB) G6 G7 (MSB) B6 B7 (MSB) (NA) LD-17Y60-5 1 cycle RxCKIN+ RxCKIN- RXIN0+ RXIN0- R3 R2 G2 R7 R6 R5 R4 R3 R2 G2 RXIN1+ RXIN1- G4 G3 B3 B2 G7 G6 G5 G4 G3 B3 RXIN2+ RXIN2RXIN3+ RXIN3DE : Display Enable NA : Not Available R1 R0 NA B1 B0 G1 G0 R1 R0 NA B5 B4 DE NA NA B7 B6 B5 B4 DE 1 cycle RxCXIN+ RxCXIN- RxIN0+ RxIN0- R1 R0 G0 R5 R4 R3 R2 R1 R0 G0 RxIN1+ RxIN1- G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 RxIN2+ RxIN2RxIN3+ RxIN3DE : Display Enable NA : Not Available R7 R6 NA B7 B6 G7 G6 R7 R6 NA B3 B2 DE NA NA B5 B4 B3 B2 DE LD-17Y60-6 2) 6 bit input 【note1】pin assignment with LVDS_SET pin (Thine:THC63LVDM83R) Transmitter Pin No 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 50 2 8 10 16 18 25 Data TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 TD0 TD1 TD2 TD3 TD4 TD5 TD6 1 cycle RXCKIN+ RXCKIN20pin =L (GND) or Open R0 (LSB) R1 R2 R3 R4 R5 (MSB) G0 (LSB) G1 G2 G3 G4 G5 (MSB) B0 (LSB) B1 B2 B3 B4 B5 (MSB) (NA) (NA) DE GND GND GND GND GND GND (NA) LVDS_SET =H (3.3V) − − − − − − − − − − − − − − − − − − − − − − − − − − − − RXIN0+ RXIN0- R1 R0 G0 R5 R4 R3 R2 R1 R0 G0 RXIN1+ RXIN1- G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 RXIN2+ RXIN2DE : Display Enable NA : Not Available B3 B2 DE NA NA B5 B4 B3 B2 DE ※In case of supplying 6 bit signal, it is recommended to connect pin No.17(Rx3-) with VCC(3.3V), and No.18(Rx3+) with GND(0V). 4-3 Interface block diagram (Computer Side) ①8Bit Mode LVDS_SET=H (20 pin=3.3[V]) LD-17Y60-7 LD-15308B-7 (TFT-LCD side) Controll R0-R5,G0 G1-G5,B0,B1 B2-B5, NA,NA,DE R6,R7,G6,G7, B6,B7,NA 7  TA 0 - 6 7  TB 0 - 6 7  TC 0 - 6 7 TD 0 - 6 THC63LVDM83R RX0+(6) TTL PARALLEL-TO-LVDS RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) CK+(15) Single LVDS interface contained in a control  RA 0 - 6 LVDS-TO-PARALLEL TTL  RB 0 - 6  RC 0 - 6 CK CＬK IN PLL ＣK-(14) PLL CK OUT ②8Bit Mode LVDS_SET=L (20 pin=GND or OPEN) Controll R2-R7,G2 G3-G7,B2,B3 B4-B7, NA,NA,DE R0,R1,G0,G1, B0,B1,NA 7  TA 0 - 6 7  TB 0 - 6 7  TC 0 - 6 7 TD 0 - 6 THC63LVDM83R RX0+(6) TTL PARALLEL-TO-LVDS RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) CK+(15) Single LVDS interface contained in a control IC  RA 0 - 6 LVDS-TO-PARALLEL TTL  RB 0 - 6  RC 0 - 6 CK CＬK IN PLL ＣK-(14) PLL CK OUT ③6Bit Mode LVDS_SET=L (20 pin=GND or OPEN) Controll R0-R5,G0 G1-G5,B0,B1 B2-B5, NA,NA,DE GND×6,NA 7  TA 0 - 6 7  TB 0 - 6 7  TC 0 - 6 7 TD 0 - 6 THC63LVDM83R RX0+(6) TTL PARALLEL-TO-LVDS RX0-(5) RX1+(9) RX1-(8) RX2+(12) RX2-(11) RX3+(18) RX3-(17) CK+(15) Single LVDS interface contained in a control IC  RA 0 - 6 LVDS-TO-PARALLEL TTL  RB 0 - 6  RC 0 - 6 CK CＬK IN PLL ＣK-(14) PLL CK OUT Internal circuits RD 0 - 6 Internal circuits RD 0 - 6 Internal circuits RD 0 - 6 LD-17Y60-8 4-4 Backlight CN 2, 3 The module-side connector The user-side connector Pin no. 1 2 symbol ＶHIGH ＶLOW I/O I I ：BHSR-02VS-1 ：SM02B-BHSS-1-TB Function Power supply for lamp Power supply for lamp (High voltage side) (Low voltage side) (JST) (JST) TFT LCD back view Red cable is VHIGH Gray cable is VLOW 1 2 CN2 CN3 Blue cable is VHIGH 1 Gray cable is VLOW 2 5. Absolute Maximum Ratings Parameter Supply voltage Lamp Input voltage Storage temperature Operating temperature Symbol Vcc VHIGH TSTG TOPA Condition Ta=25℃ − − − Ratings 0 ∼ + 4.0 0 ∼ + 2700 −25 ∼ + 60 0 ∼ + 50 Unit Ｖ Ｖrms ℃ ℃ 【Note1】 Remark 【Note1】Humidity：95%RH Max. ( Ta≦40℃ ) ( Ta>40℃ ) Maximum wet-bulb temperature at 39℃ or less. No condensation. LD-17Y60-9 6. Electrical Characteristics 6-1. TFT-LCD panel driving Parameter Vcc Supply voltage Current dissipation Permissive input ripple voltage Differential input threshold voltage Input current (High) Input current (Low) Terminal resistor High Low Symbol Vcc Icc VRF VTH VTL IOH IOL RT Min. +3.0 − − − –100 − − − Typ. +3.3 425 − − − − − 100 Max. +3.6 700 100 +100 − ±10 ±10 − Unit V mA mVp-p mV mV μA μA Ω Ta＝25℃ Remark 【Note2】 【Note3】 Vcc=+3.3V VCM=+1.2V 【Note1】 VI=2.4V, Vcc=3.6V VI=0V, Vcc=3.6V Differential input 【Note1】 VCM : Common mode voltage of LVDS driver. 【Note2】 1）On-off sequences of Vcc and data 0＜t1≦10ms 0＜t2≦10ms 0＜t3≦1s 1s≦t4 Back light OFF 0.9Vcc 0.1Vcc 0.9Vcc 0.1Vcc 0.1Vcc Vcc data t1 t2 t3 ON O FF t4 t5 200ms≦t5 Power sequence for Backlight is not especially specified, however it is recommended to consider some timing difference between LVDS input and Backlight input as shown above. If the Backlight lights on before LCD starting, or if the Backlight is kept on after LCD stopping, the screen may look white for a moment or abnormal image may be displayed. This is caused by variation in output signal from timing generator at LVDS input on or off. It does not cause the damage to the LCD module. 2）Dip conditions for supply voltage 1) 2) V2 ≦Vcc＜ V1 td≦ 10ms Vcc＜V2 Vcc-dip conditions should also follow the on-off conditions. V1 : 3.0V V2 : 2.5V V2 V1 Vcc td 【Note3】 Typical current situation : 16-gray-bar pattern Vcc=+3.3V, CK=65MHz Horizontal period =20.7 us Gray scale : GS(4n) n=0∼15 The explanation of each gray scale, GS(4n), is described RGB GS0 RGB GS4 RGB GS8 .... RGB GS56 RGB GS60 below section 8-2. LD-17Y60-10 6-2. Backlight The back light system is an edge-lighting type with 2 CCFTs (Cold Cathode Fluorescent Tube). The characteristics of the lamp are shown in the following table. The value mentioned below is at the case of one CCFT. CCFT Model Name : KTBE24MSTF-530.5KB270-Z-L (STANLEY ELECTRIC CO.,LTD) Parameter Symbol Min. Typ. Max. Unit Remark Lamp current range IL 3.0 4.5 5.0 mArms 【Note1】 Lamp voltage VL 1000 1150 Vrms − IL=4.5 mArms Ta=25℃ 60kHz Lamp power consumption PL 4.5 5.2 W − 【Note2】 IL=4.5 mArms Ta=25℃ 60kHz Lamp frequency FL 40 60 70 kHz 【Note3】 Kick-off voltage Vs 2200 Vrms − − Ta=0℃ 60kHz【Note4】 Lamp life time TL 50,000 hour 【Note5】 − − 【Note1】 A lamp can be light in the range of lamp current shown above. Maximum rating for current is measured by high frequency current measurement equipment connected to VLOW at circuit showed below. (Note : To keep enough kick-off voltage and necessary steady voltage for CCFT.) Lamp frequency : 40∼70kHz Ambient temperature : 0∼50℃ 1 Module Inverter Ａ ∼ 2 【Note2】 Referential data per one CCFT by calculation ( IL × VL ) . The data don’t include loss at inverter. 【Note3】Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. Therefore, adjust lamp frequency, and keep inverter as far as from module or use electronic shielding between inverter and module to avoid interference. 【Note4】This is transformer output voltage at 33pF for the ballast capacitor of a DC-AC inverter. The kick-off voltage may rise up in the user set, please decide the open output voltage by checking not to occur lighting failure under operating state. The open output voltage should be applied to the lamp for more than 1 second to startup. Otherwise the lamp may not be turned on. ballast capacitor(33pF) Module 1 V ∼ 2 Inverter ＊ 2pin VLOW LD-17Y60-11 【Note5】 Lamp life time is defined as the time when either ① or ② occurs in the continuous operation under the condition of Ta=25℃ and IL=5.0 mA rms. ① Brightness becomes 50% of the original value under standard condition. ② Kick-off voltage at Ta=0℃ exceeds 2200 Vrms value. 《Note》 The performance of the backlight, for example lifetime or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. When you confirm it, the module should be operated in the same condition as it is installed in your instrument. Use the lamp inverter power source incorporating such safeguard as over voltage / over current protective circuit or lamp voltage waveform detection circuit, which should have individual control of each lamp. In case one circuit without such individual control is connected to more than two lamps, excessive current may flow into one lamp when the other one is not in operation. Under the environment of 10lx or less, miss-lighting or lighting delay may occur. 7. Timing characteristics of input signals 7-1. Timing characteristics Parameter Clock signal ENAB signal Frequency Horizontal period Symbol 1/Tc TH Min. 50.0 1056 16.0 Typ. 65.0 1344 20.7 1024 806 768 Max. 80.0 1720 23.4 1024 990 768 Unit MHz clock µs clock line line Horizontal period (High) Vertical period Vertical period (High) THd TV TVd 1024 773 768 【Note】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur. TH THd DE DATA (R,G,B) 1024 1024 1 2 Tc 1 2 767 768 DE TVd TV LD-17Y60-12 7-2 Input Data Signals and Display Position on the screen R1 G1 B1 R2 G2 B2 (１､１) (１,２) １・１ １・２ １・３ ２・１ ２・２ ３・１ 1･1024 RGB 768･1024 768･1 Display Position of Data (V,H) LD-17Y60-13 8. Input Signals, Basic Display Colors and Gray Scale of Each Color 8-1 8bit input Data signal Colors & Gray R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 Gray scale Scale Black Blue Green Cyan Red Magenta Yellow White Black − − − − − − − − GS0 GS1 Darker GS2 0 0 0 0 X X X X 0 1 0 0 0 0 0 X X X X 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 X X 0 0 X X 0 0 0 0 0 X X 0 0 X X 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 X 0 X 0 X 0 X 0 0 0 0 X 0 X 0 X 0 X 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 : Low level voltage, total 24 bit data signals, the 16-million-color display can be achieved on the screen. Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue Brighter GS250 GS251 0 1 X 0 0 0 1 1 X 0 0 0 0 0 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red Black GS252 GS0 GS1 Darker GS2 Brighter GS250 GS251 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 X 0 0 0 1 1 X 0 0 0 0 0 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green Black GS252 GS0 GS1 Darker GS2 Brighter GS250 GS251 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 X 1 1 X 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Blue GS252 1 : High level voltage. X :Don’t care. Each basic color can be displayed in 253 gray scales from 8 bit data signals. According to the combination of LD-17Y60-14 8-2 6bit input Data signal Colors & Gray scale Black Blue Green Cyan Red Magenta Yellow White Black Gray Scale − − − − − − − − GS0 GS1 R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 : Low level voltage, Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen. Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue Darker GS2 Brighter GS61 GS62 1 0 1 0 0 0 0 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red Black GS63 GS0 GS1 Darker GS2 Brighter GS61 GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green Black GS63 GS0 GS1 Darker GS2 Brighter GS61 GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 Blue GS63 1 : High level voltage. LD-17Y60-15 9. Optical Characteristics Ta=25℃, Vcc =+3.3V Parameter Viewing angle Vertical Symbol θ11 θ12 Condition CR≧5 Min. 40 70 70 Typ. 55 80 80 45 55 60 350 5 20 0.313 0.329 0.581 0.322 0.307 0.546 0.151 0.127 350 Max. − − − − − − − 20 40 0.343 0.359 0.611 0.352 0.337 0.576 0.181 0.157 − Unit Deg. Deg. Deg. Deg. Deg. Deg. Remark 【Note1,4】 range Horizontal Vertical θ21,θ22 θ11 θ12 CR≧10 30 45 50 Horizontal θ21,θ22 ＣＲ γr γd x y x y x y x y YL θ=0° θ=0° Contrast ratio Response Time Rise Fall 250 − − 0.283 0.299 0.551 0.292 0.277 0.516 0.121 0.097 270 【Note2,4】 ms ms 【Note3,4】 Chromaticity of White Chromaticity of Red Chromaticity of Green Chromaticity of Blue Luminance of white 【Note4】 cd/m2 IL=4.5mA rms fL=60kHz 【Note4】 White Uniformity ※The δw − − 1.25 − 【Note5】 measurement shall be executed 30 minutes after lighting at rating. The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig.2 below. Photodetector Response Time(BM-5A) Luminance/Chromaticity/Contrast ratio (SR-3) Photodetector(EZ-CONTRAST） ４００mm Field=2° Center of screen(θ=0°） TFT-LCD-Module Fig2-1 Viewing angle measurement method Center of screen(θ=0°) TFT-LCD-Module Fig2-2 Luminance/Contrast ratio/Response time/Chromaticity measurement method Fig2 Optical characteristics measurement method LD-17Y60-16 【Note1】Definitions of viewing angle range: θ22 θ12 Normal line θ11 θ21 6 o’clock 【Note2】Definition of contrast ratio: The contrast ratio is defined as the following. Luminance (brightness) with all pixels white Contrast Ratio (CR) ＝ 【Note3】Definition of response time: Luminance (brightness) with all pixels black The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white". White 100% 90% black white Photodetector Output (Relative Value) 10% 0% τr time τd 【Note4】This shall be measured at center of the screen. 【Note5】Definition of white uniformity: White uniformity is defined as the following with five measurements 256 512 768 p ixel (A∼E). A C B D 192 384 δw＝ Maximum Luminance of five points (brightness) Minimum Luminance of five points (brightness) E 576 pixel LD-17Y60-17 10. Handling Precautions a) b) Be sure to turn off the power supply when inserting or disconnecting the cable. Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) Since the front polarize is easily damaged, pay attention not to scratch it. Blow away dust on the polarizer with antistatic Ｎ2 blow. It is undesirable to wipe off because a polarizer is sensitive. It is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to the polarizer. When unavoidable, wipe off carefully with a cloth for wiping lenses. Since long contact with water may cause discoloration or spots, wipe off water drop immediately. When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care. g) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into consideration when handling. h) i) Since there is a circuit board in the module back, stress is not added at the time of a design assembly. Please make it like. If stress is added, there is a possibility that circuit parts may be damaged. Protection film is attached to the module surface to prevent it from being scratched . Peel the film off slowly , just before the use, with strict attention to electrostatic charges. display quality. j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching protective board over the LCD, be careful about the optical interface fringe etc. which degrades display quality. k) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is used under such environment. l) Blow off 'dust' on the polarizer by using an ionized nitrogen. d) e) f) m) Make sure the four mounting holes of the module are grounded sufficiently. Take electro-magnetic interference (EMI) into consideration. n) The module has some printed circuit boards (PCBs) on the back side. Take care to keep them form any stress or pressure when handling or installing the module; otherwise some of electronic parts on the PCBs may be damaged. o) There are high voltage portions on the backlight and very dangerous. Careless touch may lead to electrical shock. When exchange lamps or service, turn off the power without tail. p) q) Observe all other precautionary requirements in handling components. When some pressure is added onto the module from rear side constantly, it causes display non-uniformity issue, functional defect, etc. So, please avoid such design. r) When handling LCD modules and assembling them into cabinets, please be noted that long-term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules. s) t) Cold cathode fluorescent lamp in LCD panel contains a small amount of mercury, please follow local ordinances or regulations for disposal. Be careful of a back light lead not to pull by force at the time of the wiring to an inverter, or line processing. LD-17Y60-18 When install LCD modules in the cabinet, recommended torque value is “0.294±0.02N･m (3.0±0.2kgf･cm)”. v) Be sure to confirm it in the same condition as it is installed in your instrument. w) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye or mouth by mistake. x) Notice:Never dismantle the module , because it will cause failure. y) Be careful when using it for long time with fixed pattern display as it may cause afterimage. z) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may not be satisfied. aa) If a minute particle enters in the module and adheres to an optical material, it may cause display nonuniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan. u) 11. Packing form a) Production country : JAPAN , TAIWAN, CHINA T.B.D T.B.D b) Piling number of cartons : c) Packing quantity in one carton : d) Carton size : T.B.D e) total mass of one carton filled with full modules : f) Packing form is shown : T.B.D T.B.D LD-17Y60-19 12．Reliability test items No 1 2 3 4 5 6 Test item High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Vibration test (non- operating) Conditions Ta = 60℃ Ta = -25℃ 240h 240h 240h Ta = 40℃ ; 95%RH (No condensation) Ta = 60℃ Ta = 0℃ 240h 240H (The temperature of panel surface) Waveform : Sine wave Frequency : 10∼57Hz/Vibration width (one side) : 0.075mm : 57∼500Hz/Gravity : 9.8m/s2 Sweep time : 11minutes Test period : 3 hours (1 hour for each direction of X,Y,Z) 7 Shock test (non- operating) Max. gravity : 490m/s2 Pulse width : 11ms, half-sine wave Direction : ±X, ±Y, ±Z, once for each direction. 8 9 Thermal shock test (Storage) Altitude Ta=-25℃∼60℃ ; 5 cycles Test period : 10 hours (1 hour for each temperature) Ta=50℃,70kPa,3,048m(10,000ft), t=24h Ta=70℃,12kPa,15,240m(50,000ft), t=24h 【Result Evaluation Criteria】 Under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function. (normal operation state：Temperature:15∼35℃, Humidity:45∼75％, Atmospheric pressure:86∼106kpa) (Operating) (Storage) LD-17Y60-20 13．Others 1) Lot No. and indication Bar Code Label: SHARP LQ150X1LGN2E XX XXXXXXX MADE IN JAPAN Model No. Bar Code( Lot No. ) Lot No. Production Country Production country Japan Taiwan China MADE IN JAPAN MADE IN TAIWAN MADE IN CHINA How to express Lot No. A production year (the last figures of the Christian Era) A production month (1∼9,X,Y,Z) Serial No. 2) Packing Label （４Ｓ） LQ150X1LGN2E 社内品番： B ar code（①） ＬｏｔＮＯ． TYPE QUANTITY LOT(DATA) LQ150X1LGN2E ① （１Ｔ）２００５．Ｘ．ＸＸ ： １０ ０５．１１．２５ ③ ② B ar code（②） （Ｑ） Ｑｕａｎｔｉｔｙ： B ar code（③） ユーザ品番 ： １０ ｐｃｓ Made in TAIWAN ① Model No. (LQ150X1LGN2E) ② Lot No. (Date) ③ Quantity シャープ物流用ラベルです。 Made in JAPAN / CHINA 3) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may not be satisfied. 4) Disassembling the module can cause permanent damage and should be strictly avoided. 5) Please be careful since image retention may occur when a fixed pattern is displayed for a long time. 6) The chemical compound which causes the destruction of ozone layer is not being used. 7) Warning of mercury and material information of LPG (Light Pipe Guide) are printed on the back of the module. MATERIAL INFORMATION >PLASTIC LIGHT GUIDE:PMMA< 8)Cold cathode fluorescent lamp in LCD PANEL contains a small amount of mercury, Please follow local ordinances or regulations for disposal. COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS A SMALL AMOUNT OF MERCURY, PLEASE FOLLOW LOCAL ORDINANCES OR REGULATION FOR DISPOSAL 当 該液晶ディスプレイパネルは蛍光管が組み込まれていますので、地方自冶体の条 例、または、規則に従って廃棄ください。 9) If any problem occurs in relation to the description of this technical literature, it shall be resolved through discussion with spirit of cooperation. LD-17Y60-21 14. Carton storage condition Temperature Humidity 0℃ to 40℃ 95%RH or less 20℃ to 35℃ , 85%RH or less 5℃ to 15℃ , 85%RH or less (summer) (winter) Reference condition : : ・the total storage time (40℃,95%RH) : 240H or less Sunlight Atmosphere Be sure to shelter a product from the direct sunlight. Harmful gas, such as acid and alkali which bites electronic components and/or wires must not be detected. Notes Be sure to put cartons on palette or base, don’t put it on floor, and store them with removing from wall Please take care of ventilation in storehouse and around cartons, and control changing temperature is within limits of natural environment Storage period 1 year