LQ070Y3DG3A

RECORDS OF REVISION LQ070Y3DG3A ^SPEC No. LD-21212A DATE Feb.17.2009 SUMMARY REVISED No. PAGE - - NOTE 1st Issue LD21212A-1 These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. In case of using the device for applications such as control and safety equipment for transportation(aircraft, trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken. Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment for life support. SHARP assumes no responsibility for any damage resulting from the use of the device, which does not comply with the instructions, and the precautions specified in these specification sheets. Contact and consult with a SHARP sales representative for any questions about this device. LD21212A-2 Table of contents 1. Application ..............................................................................3 2. Overview ................................................................................3 3. Mechanical Specifications ...................................................................3 4. Input Terminals ...........................................................................4 4-1. TFT-LCD panel driving .................................................................4 4-2. LED- Backlight driving .................................................................4 5. Absolute Maximum Ratings .................................................................5 6. Electrical Characteristics ....................................................................5 6-1.TFT-LCD panel driving .................................................................5 6-2. Backlight driving ......................................................................7 7. Timing Characteristics of Input Signals ........................................................7 7-1. Timing characteristics ..................................................................7 7-2. Display position .......................................................................8 7-3. Input data signals and display position on the screen...........................................8 Fig 1. Input signal timing chart .................................................................9 8. Input Signals, Basic Display Colors and Gray Scale of Each Color ..................................10 9. Optical Characteristics.....................................................................11 10. Display Quality .........................................................................12 11. Handling Precautions.....................................................................13 12. Packing form ...........................................................................14 13. Reliability Test Items.....................................................................14 14. Label .................................................................................15 15. Storage conditions .......................................................................16 Fig 2. Packing form .........................................................................17 Fig 3. Outline demensions ....................................................................18 LD21212A-3 1. Application This specification applies to a color TFT-LCD module, LQ070Y3DG3A. 2. Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, power supply circuit, and a backlight unit. Graphics and texts can be displayed on a 800×3×480 dots panel with 16,194,277 colors by supplying 24bit digital signal interface (RGB×8bit)and supplying +3.3V DC supply voltages for TFT-LCD panel driving and supply voltage for backlight. In this TFT-LCD panel , low reflection / color filters of excellent color performance and backlights of high brightness are incorporated to realize brighter and clearer pictures, making this model optimum for use in multi-media applications. Optimum viewing direction is 6 o'clock. Backlight-driving DC/DC converter is not built in this module. 3. Mechanical Specifications Parameter Specifications Unit Display size 17.8 (7.0") Diagonal cm Active area 152.4(H)×91.4 (V) mm 800 (H)×480 (V) pixel Pixel format (1 pixel = R+G+B dots) Aspect ratio 15 : 9 Pixel pitch 0.1905 (H)×0.1905 (V) Pixel configuration R,G,B Horizontal stripe Display mode Normally white Surface treatment Anti-Glare and hard-coating 2H Parameter Unit outline dimensions [Note 1] Mass mm Min. Typ. Max. Unit Width 162.9 163.2 163.5 mm Height 103.7 104.0 104.3 mm Depth − 3.9 4.2 mm − − 6.3 mm − 135 150 g [Note 1] Excluding the FPC/FFC and parts mounting area. Outline dimensions is shown in Fig.3 [Note 2] Including the FPC/FFC and parts mounting area. Remark [Note 1] [Note 2] LD21212A-4 4. Input Terminals 4-1. TFT-LCD panel driving CN1(Timing signals,DATA signals and +3.3V DC power supply) Pin No. 1 Symbol GND Function Pin No. 21 Symbol B0 Function BLUE data signal(LSB) 2 GND 22 B1 BLUE data signal 3 VCC +3.3V Power Supply 23 B2 BLUE data signal 4 VCC +3.3V Power Supply 24 B3 BLUE data signal 5 R0 RED data signal(LSB) 25 B4 BLUE data signal 6 R1 RED data signal 26 B5 BLUE data signal 7 R2 RED data signal 27 B6 BLUE data signal 8 R3 RED data signal 28 B7 BLUE data signal(MSB) 9 R4 RED data signal 29 GND 10 R5 RED data signal 30 DOTCLK 11 R6 RED data signal 31 NC 12 R7 RED data signal(MSB) 32 HSYNC Line synchronization signal 13 G0 GREEN data signal(LSB) 33 VSYNC Frame synchronization signal 14 G1 GREEN data signal 34 DEN Display enable signal 15 G2 GREEN data signal 35 NC 16 G3 GREEN data signal NC 17 G4 GREEN data signal 36 37 GND 18 G5 GREEN data signal 38 GND 19 G6 GREEN data signal 39 NC 20 G7 GREEN data signal(MSB) 40 NC Dot-clock signal [Note 1] Please use NC by OPEN or GND. NC terminal is not connected with the internal circuit. Using FFC : SML2CD-40X77.5-ADX7(BL)-P0.5-S4.0+4.0-M-N(35)-AUP-HF UL21147(Sumitomo Electric Industries, Ltd) Recommendation connector : FH28-40S-0.5SH(0.5) (HIROSE):Bottom contact FH12A-40S-0.5SH(55) (HIROSE):Top contact (Sharp is not responsible to its product quality, if the user applies a connector not corresponding to the above model.) 4-2. LED- Backlight driving Pin No. Symbol 1 2 LED-A1 LED-C1 Function Power supply for LED (Anode) Power supply for LED (Cathode) 3 4 LED-A2 LED-C2 Power supply for LED (Anode) Power supply for LED (Cathode) 5 6 LED-A3 LED-C3 Power supply for LED (Anode) Power supply for LED (Cathode) [Note 1]LED-FPC outline dimensions is shown in Fig.3 Reccommendation connector: 04-6298-006-000-883+ (Kyosera) : Bottom contact 04-6277-006-000 or 001-883+ (Kyosera) : Double-sided contact LD21212A-5 5. Absolute Maximum Ratings Parameter Symbol Condition VI +3.3V supply voltage Ratings Unit Remark Vcc+0.3 V [Note 1] 0 +4.0 V Ta=25℃ 0 30 mA VLED_R Ta=25℃ − 5 V Storage temperature Tstg − -30 +70 ℃ Operating temperature Topa − -20 +50 ℃ Min. Max. Ta=25℃ -0.3 VCC Ta=25℃ LED forward current ILED LED reverse voltage Input voltage [Note 2] [Note 3] [Note 1] R0-7、G0-7、B0-7、DOTCLK、HSYNC、VSYNC、DEN [Note 2] LED_A to LED_Cn (n=1,2,3) Absolute maximum ratings for each pair. [Note 3] Humidity：95%RH Max. at Ta≦+40℃. Maximum wet-bulb temperature at +39℃ or less at Ta>+40℃. No condensation. 6. Electrical Characteristics 6-1.TFT-LCD panel driving Ta＝+25℃ Parameter Supply voltage Symbol VCC Min. +3.0 Typ. +3.3 Max. +3.6 Current dissipation Permissive input ripple voltage Icc VRP − − 140 185 100 Input voltage range High Low VTH VTL − 0.7×VCC − − Input leak current High Low IOH IOL − − − − − Unit V [Note 1] mA [Note 2] mVP-P Vcc = +3.3V 0.3×VCC − ±10 ±10 Remark mV mV [Note 3, 4] μA μA VI = Vcc VI = 0V [Note 3, 4] [Note 3, 4] [Note 1]On-off conditions for supply voltage 0.9Vcc 0.9Vcc 0.1Vcc 0.1Vcc Vcc t1 Valid t2 t3 Signal (LVDS interface) t6 t7 Backlight ON Backlight OFF t4 t5 0.1Vcc LD21212A-6 Symbol Min. Max. Unit Remark t1 0 10 ms t2 0 1 ms t3 0 1 ms t4 0 400 ms t5 1 − s t6 180 − ms *1 t7 5 − ms *1 *1 : As for the power sequence for backlight, it is recommended to apply above mentioned input timing. If the backlight is lit on and off at a timing other than shown above, displaying image may get disturbed. [Note] Do not keep the interface signal high-impedance or unusual signal when power is on. Vcc-dip conditions 1) Vcc 2.5 V≦Vcc＜3.0 V td≦10 ms Under above condition, the display image should return to Ｖ ５ ． ２ an appropriate figure after Vcc voltage recovers. 2) Vcc＜2.5 V Ｖ ０ ． ３ td Vcc-dip conditions should also follow the On-off conditions for supply voltage RGB [Note 2] Typical current situation : GS0 RGB RGB GS16 GS24 VCC = +3.3V, fVSYNC = 60Hz Measuring pattern:GS-0-GS60 Vertical gray scale. GS(4n) n:Natural number(0∼15) [Note 3] R0-7、G0-7、B0-7、DOTCLK、HSYNC、VSYNC、DEN [Note 4] Interface block diagram of the LCD R 0∼ R7 G 0∼ G7 8 8 56Ω 56Ω 56Ω 8 8 8 R 0∼ R7 G 0∼ G7 B 0∼ B7 56Ω VS VS 56Ω HS HS 56Ω E N AB E N AB Control IC Interface FFC B 0∼ B7 8 56Ω CK ＶＣＣ RGB RGB .... CK Internal Cuircuit GS224 GS240 LD21212A-7 6-2. Backlight driving The backlight system is edge-lighting type with 24 White-LED(White Light Emitting Diode). (Ta=25 oC) The characteristics of White-LED are shown in the following table. Parameter Symbol Min. Typ. Max. Unit Remark LED voltage VL − 25.6 28 V IL=20mA LED current range IL − 20 25 mA − 3 − Number of circuit strings [Note 1] LED power consumption WL − 1.54 − W [Note 2] LED life time LL 10000 − − Hour [Note 3] [Note 1] The LED backlight is composed by 3 strings from which 8 LED is connected with the series. The figure below shows the circuit chart. In each string, there is a ceramic capacitor for the electrostatic protection. LED-A1 Ceramic capacitor LED-C1 LED-A2 LED-C2 LED-A3 LED-C3 [Note 2] Calculated value for reference ( IL × VL ) [Note 3] LED life time is defined as the time when Brightness becomes 50 % of the original value. under the condition of Ta = 25℃ and IL = 20 mA,and continuous lighting. 7. Timing Characteristics of Input Signals 7-1. Timing characteristics Characteristics DOTCLK Frequency High Width Lo Width Duty DATA Setup Time Hold Time HSYNC Period Symbol 1/Tc Tch Tc1 Th/T Tds Tdh TH Min. 31.95 10 10 40 5 5 31.45 1024 5 520 2 800 Typ. 33.26 − − 50 − − 31.75 1056 128 525 − 800 Max. 34.6 − − 60 − − − 1088 186 530 TV-515 800 Unit MHz ns ns % ns ns µs clock clock line line line Remark Pulse Width THp Period TV Pulse Width TVp Horizonral Display Area THd Phase difference of THc 8 Tc-10 ns − HSYNC - DOTCLK Phase difference of TVh 1 TH-THp-10 clock − HSYNC - VSYNC Vertical Back Porch TVs 35 35 35 line Vertical Front Porch TVf 5 line − − Vertical Display Area TVd 480 480 480 line [Note1] In case of lower frequency, the deterioration of display quality, flicker etc., may be occurred. VSYNC LD21212A-8 7-2. Display position Characteristics DEN Symbol Min. Typ. Max. Unit Tes 5 − − Tc-10 − ns Setup time Remark Pulse width Tep 800 clock Phase difference of − THe 88 215 clock HSYNC - DEN [Note] (Horizontal display direction) When “DEN” signal is fixed low, 216 clocks are counted from Hsync negative edge and data from after are available. If you need other timing, please use “DEN” signal. (Vertical display direction) 36 lines are counted from Vsync negative edge and data from next line are available. (“DEN” signal) When “DEN” signal is active, “DEN” signal input continuously or fixed “L” in Vertical invalid data period. Caution Image will not be displayed on the right position otherwise. 7-3. Input data signals and display position on the screen 1・ 1 1・ 2 2・ 1 2・ 2 1･800 1・ 3 3・ 1 B G R 480･800 480･1 Display position of input data(V・ H) LD21212A-9 TH THp c c V 3 . 0 c c V 7 . 0 c c V 3 . 0 Horizontal sync. signal (Hsync) Tc c c V 7 . 0 THc Tch * Only when “DEN” terminal is fix ed "L ow" c c V 7 . 0 c c V 3 . 0 Clock signal (DOTCLK) C1* C215* Tds C216* Num ber of clock Nu mber of H-data Tdh c c V 7 . 0 D1 Horizontal invalid data period D2 THe D799 Horizontal invalid da ta period D800 THd c c V 7 . 0 Tes c c V 3 . 0 Data enable signal (DEN) D3 c c V 3 . 0 Data signal (R0~R5,G0~G5, B0~B5) Tcl Tep TV c c V 7 . 0 TVp c c V 3 . 0 c c V 3 . 0 Vertical sync. signal (Vsync) TVh c c V 7 . 0 Horizontal sync. signal (Hsync) 1 2 35 “DEN” signal input continuously or fixed “L” in Vertical invalid data period Num ber of lin e Data enable signal (DEN) Data signal (R0~R5,G0~G5, B0~B5) Vertical invalid data period TVf TVd TVs DH1 DH2 DH3 DH479 DH480 Vertical invalid data period Nu mber o f V-d ata line Fig 1. Input signal timing chart LD21212A-10 8. Input Signals, Basic Display Colors and Gray Scale of Each Color Data signal Colors & Gray R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Gray scale Scale Black − 0 0 0 0 0 0 0 0 Blue − 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 Green − 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Cyan − 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 X X 1 1 1 1 1 1 Red − X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Magenta r o l o C c i s a B Gray Scale of Red − X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 Yellow − X X 1 1 1 1 1 1 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 White − X X 1 1 1 1 1 1 X X 1 1 1 1 1 1 X X 1 1 1 1 1 1 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × È 0 0 0 0 È È GS250 È È 0 È È È 1 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Ø GS251 1 1 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Brighter GS252 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Ø È Red GS255 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 È È È Gray Scale of Green × GS1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × È È È È È È È È GS250 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 0 0 0 0 0 0 0 0 Ø GS251 0 0 0 0 0 0 0 0 1 1 0 1 1 1 1 1 0 0 0 0 0 0 0 0 Brighter GS252 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Gray Scale of Blue Ø È Green Gs255 0 0 0 0 È 0 0 0 0 X X 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 × GS1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 × È 1 1 1 1 È È GS250 È È È 0 0 0 0 È È È 0 0 0 0 0 0 0 0 È 0 0 0 0 0 1 0 1 Ø GS251 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 1 1 1 1 Brighter GS252 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 X X 1 1 1 1 1 1 Ø È Blue GS255 1 1 1 1 È 0 0 : Low level voltage, 0 0 0 È 0 0 0 0 1 : High level voltage. 0 0 0 0 È 0 0 0 0 X X 1 1 Ｘ :Don’t care(GS252∼GS255 are same grayscale) Each basic color can be displayed in 253 gray scales from 8 bit data signals. According to the combination of total 24 bit data signals, the 16-million-color display can be achieved on the screen. LD21212A-11 9. Optical Characteristics Ta=+25℃, Vcc=+3.3V Parameter Horizontal Viewing angle range Vertical Symbol Condition θ21,θ22 θ11 CR>10 θ12 Min. Typ. Max. Unit − 65 − Deg. − 50 − Deg. − 60 − Deg. 300 − − Contrast ratio CRn Response time τr+τd − 35 40 x 0.252 0.302 0.352 y 0.279 0.329 0.379 x 0.533 0.583 0.633 0.272 0.322 0.372 x 0.274 0.324 0.374 y 0.498 0.548 0.598 x 0.103 0.153 0.203 y 0.048 0.098 0.148 YLI 280 350 − Chromaticity of white Chromaticity of red Chromaticity of green Chromaticity of blue Luminance of white ※ y θ=0° θ=0° Remark [Note 1,3,6] [Note 2,4,6] ms [Note 2,5,6] [Note 2,6] cd/m2 If=20mA The measurement shall be executed 30 minutes after lighting at rating. Condition : (If=20mA) The optical characteristics shall be measured in a dark room or equivalent. [Note 1] Measuring Viewing Angle Range [Note 2] Other Measurements EZ contrast 160RH (ELDIM) BM-5A 400mm (TOPCON) Field=２° Center of the screen (θ=0°) LCD Panel Center of the screen (θ=0°) LCD Panel [Note 2,6] LD21212A-12 [Note 3] Definitions of viewing angle range: [Note 4] Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) ＝ Luminance (brightness) with all pixels white Luminance (brightness) with all pixels black [Note 5] Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white" . [Note 6] This shall be measured at center of the screen. 10. Display Quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. LD21212A-13 11. Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. Please insert for too much stress not to join FFC/FPC in the case of insertion of FFC/FPC. b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) Since the front polarizer is easily damaged, pay attention not to scratch it. d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care. g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when handling. Observe all other precautionary requirements in handling components. h) This module has its circuitry PCBs on the rear side and should be handled carefully in order not to be stressed. i) Protect sheet(Laminate film) is attached to the module surface to prevent it from being scratched. Peel the sheet off slowly just before the use with strict attention to electrostatic charges. Ionized air shall be blown over during the action. Blow off the 'dust' on the polarizer by using an ionized nitrogen gun, etc. Working under the following environments is desirable. ・All workers wear conductive shoes, conductive clothes, conductive fingerstalls and grounding belts without fail. ・Use Ionized blower for electrostatic removal, and peel of the protect sheet with a constant speed. (Peeling of it at over 2 seconds) j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching protective board over the LCD, be careful about the optical interface fringe etc. which degrades display quality. k) Do not expose the LCD module to a direct sunlight, for a long period of time to protect the module from the ultra violet ray. l) When handling LCD modules and assembling them into cabinets, please be noted that long-term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules. m) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye or mouth by mistake. n) Disassembling the module can cause permanent damage and should be strictly avoided. Please don't remove the fixed tape, insulating tape etc that was pasted on the original module. (Except for protection film of the panel.) o) Be careful when using it for long time with fixed pattern display as it may cause afterimage. (Please use a screen saver etc., in order to avoid an afterimage.) p) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may not be satisfied. q) If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity LD21212A-14 issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan. r) Epoxy resin (amine series curing agent), silicone adhesive material (dealcoholization series and oxime series), tray forming agent (azo compound) etc, in the cabinet or the packing materials may induce abnormal display with polarizer film deterioration regardless of contact or noncontact to polarizer film. Be sure to confirm the component of them. s) Do not use polychloroprene. If you use it, there is some possibility of generating Cl2 gas that influences the reliability of the connection between LCD panel and driver IC. t) Do not put a laminate film on LCD module, after peeling of the original one. If you put on it, because of the occurrence of air gaps between the polarizer and the film, It may cause discoloration or spots. 12. Packing form Piling number of cartons Max.8 Package quantity in one carton 40pcs Carton size 380 (W)×575(D)×225(H) mm Total mass of one carton filled with full modules 10 kg Packing form Fig.2 13. Reliability Test Items No. 1 Test item High temperature operation test Conditions Ta = +50℃ 240h 2 Low temperature operation test Ta = -20℃ 240h 3 High temperature storage test Ta = +70℃ 240h 4 Low temperature storage test Ta = -30℃ 240h 5 High temperature Ta = +40℃ ; 95 %RH 240h & high humidity operation test (No condensation) Frequency range: 10 to 55Hz Sweep: 1.5mm Sweep time: 1minute Test period: 2 hours for each direction of X,Y,Z Direction: ±X, ±Y, ±Z, Time: 3 times for each direction. Impact value: 980m/s², Action time 6ms 6 Vibration test (non- operating) 7 Shock test [Result Evaluation Criteria] Under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function. (normal operation state：Temperature:15∼35℃, Humidity:45∼75％, Atmospheric pressure:86∼106kpa) LD21212A-15 14. Label 1) Module label: Notation: ①Model No. ②Serial No. ① ② ＬＱ ０７０Ｙ３Ｄ Ｇ３Ａ ９２０００００１_ Details of Serial No ９ ２ ０ ０ ０ ０ ０ １ (Example) Revision Code(None, A,B,・・・) Production year(9∼) Serial No(000001∼) Production Month(1∼9,X,Y,Z) [Note] Production year ： 9(2009)、0(2010)、1(2011)、・・・・ Production Month： 1(Jan)、2(Feb)、・・・、9(Sep)、X(Oct)、Y(Nov)、Z(Dec) 2) Packing bar code label Notation/ Bar code: ①Model No. ②Date ③Quantity 社内品番：（４Ｓ）ＬＱ０７０Ｙ３ＤＧ３Ａ Bar code（①） Ｌｏｔ Ｎo． ：（１Ｔ）２００９．０２．０１ Bar code(②） Ｑｕａｎｔｉｔｙ：（Ｑ） ４０ ① ② ③ ｐｃｓ Bar code（③） ユーザ品番 ： シャープ物流用ラベルです。 Ｒ．Ｃ． ※R.C.（RoHS Compliance）means these parts have corresponded with the RoHS directive. LD21212A-16 15. Storage conditions Temperature 0 to 40 degrees Celsius Relative humidity 70% and below Direct sun light Please keep the product in a dark room or cover the product to protect from direct sun light. Atmospheric condition Please refrain from keeping the product with possible corrosive gas or volatile flux. Prevention of dew * Please store the product carton either on a wooden pallet or a stand / rak to prevent dew. Do not place directly on the floor. In addition, to obtain moderate ventilation in between the pallet’s top and bottom surfaces, pile the cartons up in a single direction and in order. * Please place the product cartons away from the strage wall. * Please maintain the storage area with an appropriate ventilation. It is recommendable to furnish the storage area with equipments such as ventilation systems. * Please maintain the ambient temperature within the range of natural environmental fluctuation. LD21212A-17 Fig 2. Packing form LD21212A-18 Fig 3. Outline dimensions