RECORDS OF REVISION
LQ104S1LG81
SPEC No.
DATE
LD-24403A
2012/4/27
LD-24403B
2012/6/20
REVI
SED
No PAGE
SUMMARY
-
１
6
Revised ： 4-4．LED backlight CN2 connector maker
NOTE
- Contents -
No.
page
1
Application
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
1
2
Overview
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
2
3
Mechanical Specifications ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
2
4
Input Terminals
5
Absolute Maximum Ratings
6
Electrical Characteristics ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 7,8
7
Timing characteristics of input signals
8
Input Signals, Basic Display Colors and Gray Scale of Each Color
9
Optical Characteristics
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 11,12
10
Handling Precautions
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 13,14
11
Packing form
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
15
12
Reliability test items
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
15
13
Others
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
16
14
Storage conditions
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
17
Fig.1
OUTLINE DIMENSIONS
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
18
Fig.3
PACKING FORM
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
19
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 3〜6
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・
・・
6
9
10
LD-24403B- 1
1．Application
This specification applies to the color TFT-LCD module LQ104S1LG81.
This specification is the proprietary product of SHARP CORPORATION (SHARP) and include
materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in
any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express
written permission of SHARP.
The device listed in this specification was designed and manufactured for use in general electronic
equipment.
In case of using the device for applications such as control and safety equipment for transportation (controls of
aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which
require higher reliability and safety, take into consideration that appropriate measures such as fail-safe
functions and redundant system design should be taken.
Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,
telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment
for life support.
SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply
with the instructions and the precautions specified in this specification .
Contact and consult with a SHARP sales representative for any questions about this device.
LD-24403B- 2
2．Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).
It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a White-LED
Backlight unit. Graphics and texts can be displayed on a 800×RGB×600dots panel with about 262,144 million
colors by using LVDS (Low Voltage Differential Signaling) and supplying +3.3V DC supply voltages for
TFT-LCD panel driving and supply voltage for backlight.
The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation type.
The maximum viewing angle is in the 6 o'clock direction.
The 12 o'clock direction is difficult to reverse the grayscale.
The LED driver circuit to drive the backlight is built into the module.
3．Mechanical technical literatures
Parameter
technical literatures
Unit
Display size
26（10.4inch）Diagonal
cm
211.2（H)×158.4（V)
mm
Active area
Pixel format
800（H)×600（V)
(1pixel＝R＋G＋B dot)
pixel
Aspect ratio
4：3
Pixel pitch
0.264（H)×0.264（V)
Pixel configuration
R,G,B vertical stripe
Display mode
Normally white
Unit outline dimensions
246.5（W)×179.3（H)×12.5(D)
mm
Mass
max 500
g
Surface treatment
Anti-glare and hard-coating 3H
Outline dimensions are shown in Fig.1.
mm
LD-24403B- 3
4．Input Terminals
4-1．TFT-LCD panel driving
CN1（Interface signals and +3.3V power supply）
Used connector：FI-SEB20P-HFE(JAE)
Corresponding connectors：FI-SE20M or FI-S20S(conector) (JAE)
CN1
Pin
Symbol
Function
1
VCC
+3.3V Power supply
2
VCC
+3.3V Power supply
3
GND
4
GND
5
RxIN0-
LVDS receiver signal CH0 (-)
LVDS
6
RxIN0+
LVDS receiver signal CH0 (+)
LVDS
7
GND
8
RxIN1-
LVDS receiver signal CH1 (-)
LVDS
9
RxIN1+
LVDS receiver signal CH1 (+)
LVDS
10
GND
11
RxIN2RxIN2
LVDS receiver signal CH2 ((-))
LVDS
12
RxIN2+
LVDS receiver signal CH2 (+)
LVDS
13
GND
14
RXCLK IN-
LVDS receiver signal CK (-)
LVDS
15
RXCLK IN+
LVDS receiver signal CK (+)
LVDS
16
GND
17
NC
18
SCAN
Horizontal/Vertical display mode select signal
【Note１】
19
GND
20
GND
【Note１】 SCAN = LOW
Remark
SCAN = HIGH
LD-24403B- 4
4-2．Data Mapping
1) data mapping
1 cycle
R1
R0
G0
R5
G2
G1
B1
B0
B3
B2
DE
NA
R4
R3
R2
R1
R0
G0
G5
G4
G3
G
G1
B1
NA
B5
B4
B3
B2
DE
DE：Display Enable
NA：Not Available
2) When you use the transmitter in 6bits
Corresponding LVDS Transmitter
Transmitter
THC63LVDM63A（Thine electronics） or Compatible product
Pin No
Data
24
TxIN0
R0 (LSB)
26
TxIN1
R1
27
TxIN2
R2
29
TxIN3
R3
30
TxIN4
R4
31
TxIN5
R5 (MSB)
33
TxIN6
G0 (LSB)
34
TxIN7
G1
35
TxIN8
G2
37
TxIN9
G3
39
TxIN10
G4
40
TxIN11
G5(MSB)
41
TxIN12
B0 (LSB)
43
TxIN13
B1
45
TxIN14
B2
46
TxIN15
B3
47
TxIN16
B4
1
TxIN17
B5(MSB)
2
TxIN18
（NA)
4
TxIN19
（NA)
5
TxIN20
DE
LD-24403B- 5
3) When you use the transmitter in 8 bits
Corresponding LVDS Transmitter
THC63LVDM83R（Thine electronics） or Compatible product
Transmitter
Pin No
Data
51
TA0
R0 (LSB)
52
TA1
R1
54
TA2
R2
55
TA3
R3
56
TA4
R4
3
TA5
R5 (MSB)
4
TA6
G0 (LSB)
6
TB0
G1
7
TB1
G2
11
TB2
G3
12
TB3
G4
14
TB4
G5(MSB)
15
TB5
B0 (LSB)
19
TB6
B1
20
TC0
B2
22
TC1
B3
23
TC2
B4
24
TC3
B5(MSB)
27
TC4
（NA)
28
TC5
（NA)
30
TC6
DE
50
TD0
GND
2
TD1
GND
8
TD2
GND
10
TD3
GND
16
TD4
GND
18
TD5
GND
25
TD6
GND
LD-24403B- 6
4-3．Interface block diagram
1) When you use the transmitter in 6bits
Controller
Control IC (LVDS内蔵）
7
G1-G5,B0,B1
RXIN1+
TxIN14-20
TTL PARALLEL-TO-LVDS
B2-B5, HS,VS,DE
R0-R5,G0
RXIN0-
TxIN 7 - 13
B2-B5, NA,NA,DE
RXIN1RXIN2+
RXIN2-
Internal circuits
7
G1-G5,B0,B1
RXIN0+
TxIN0 - 6
LVDS-TO-PARALLEL TTL
7
R0-R5,G0
RXCKIN+
TxCLKIN
CK
CK OUT
PLL
PLL
RXＣKIN-
2) When you use the transmitter in 8bits
THC63LVDM83R
7
TB 0 - 6
7
TC 0 - 6
B2-B5, HS,VS,DE
7
ALL GND
R0-R5,G0
RXIN0-
G1-G5,B0,B1
RXIN1+
TD 0 - 6
B2-B5, NA,NA,DE
RXIN1-
RD 0 - 6
RXIN2+
RXIN2RXIN3+
NC
RXIN3-
NC
Internal circuits
G1-G5,B0,B1
Control IC (LVDS内蔵）
RXIN0+
TA 0 - 6
TTL PARALLEL-TO-LVDS
7
R0-R5,G0
LVDS-TO-PARALLEL TTL
Controller
RXCKIN+
CＬK IN
CK
4-4．LED backlight
LED backlight connector
CN2
Used connector
Corresponding connector
Connector No.
CN2
Pin No.
1
2
3
4
5
6
CK OUT
PLL
：
：
PLL
RXＣKIN-
SM06B-SHLS-TF
SHLP-06V-S-B
symbol
VDD
VDD
GND
GND
XSTABY
VBR
(
(
JST
JST
１
１
)
)
function
+12V power supply
+12V power supply
GND
GND
Backlight ON/OFF signal
PWM signal
5．Absolute Maximum Ratings
Parameter
Supply voltage
Symbol
Vcc
VDD
VⅠ1
Condition
Ta=25℃
Ta=25℃
Ta=25℃
Pin
Ratings
Unit
Remark
VCC
-0.3 ～ +4.0
V
【Note1,2】
VDD
-0.3 ～ +15
V
【Note1,2】
-0.3～VCC+0.3
SCAN
V
RxINi-/+
-0.3～VCC+0.3
Input voltage
VⅠ2
Ta=25℃
V
i=0,1,2,3
RXCLK IN-/+
VⅠ3
Ta=25℃
XSTABY, VBR
-0.3～+6
V
Storage temperature
℃
－
-30 ～ +80
【Note1】
TSTG
Operating temperature
TOPA
－
-30 ～ +80
℃
【Note1,3,4】
【Note1】 Humidity：95%RH Max.( Ta≦40℃ ) Note static electricity.
Maximum wet-bulb temperature at 39℃ or less. (Ta>40℃) No condensation.
【Note2】 The Vcc power supply capacity must use the one of 2A or more.
The VDD power supply capacity must use the one of 3A or more.
【Note3】
There is a ppossibilityy of causingg deterioration in the irregularity
【
】
g
y and others of the screen and the display
p y
fineness though the liquid crystal module doesn't arrive at destruction when using it at 65～80℃.
【Note4】 In the operating temperature item, the low temperature side is the ambient temperature regulations.
The high temperature side is the panel surface temperature regulations.
LD-24403B- 7
6．Electrical Characteristics
Ta＝+25℃
6-1．TFT-LCD panel driving
Min.
Typ.
Max.
Unit
Remark
3.0
3.3
3.6
V
【Note1】
-
240
360
mA
【Note2】
VL
0
－
2.5
V
【Note4】
VRP
－
－
mVP-P
－
100
VCM +100
mV
Vcc = 3.3V
VCM =+1.25V
－
－
mV
【Note4】
【Note3】
Parameter
Symbol
Supply voltage
VCC
Current dissipation
ICC
LVDS Input voltage
Permissive input ripple voltage
Condition
Vｃｃ=3.3V
Differential input
High
VTH
Threshold voltage
Low
VTL
－
VCM -100
VIH
2.0
-
Vcc+0.3
V
VIL
-0.3
-
0.8
V
IOH
－
－
400
IOL
-5
－
－
RT
－
100
－
Input voltage
Input leak current
Terminal resistor
μA VI2 =+3.3V【Note3】
VI2 =0V 【Note3】
μA
Differential input
Ω
【Note1】 On-off conditions for supply voltage
0.1 VCC
0.1 VCC
t1
VCC
t3 t15 t4
t2
D t
Data
Back light
OFF
20μs ＜ t1 ≦ 10ms
0.9 VCC
0.9 VCC
0
＜ t2 ≦ 20ms
0
＜ t3 ≦
1s
≦ t4
1s
300
300ms
≦ t5
ON
t5
300ms ≦ t6
t6
OFF
t15 ≦ 100ms
Vcc-dip conditions
・
VCC
Vth
＜ VCC ≦ Vmin
td ≦ 10ms
Vmin
Vth
Vth =
Vmin =
2.5V
3.0V
・ VCC ＜ Vth
Vcc-dip conditions should also follow the On-off
conditions for supply voltage
td
・
The relation between the data input and the backlight lighting will recommend the above-mentioned input sequence.
When the backlight is turned on before the panel operates, there is a possibility of abnormally displaying.
The liquid crystal module is not damaged.
【Note2】 Current dissipation
RGB RGB RGB
GS0 GS1 GS2
Typical current situation : 64-gray-bar pattern
（ Vcc=+3.3V、fck = 40MHz、Ta=25℃）
【Note3】 SCAN
【Note4】 RXIN0-,RXIN0+,RXIN1-,RXIN1+,RXIN2-,RXIN2+,RXCLK IN-,RXCLK IN+
RGB RGB
・・・ GS62
GS63
LD-24403B- 8
6-2．LED backlight
Ta＝+25℃
Parameter
Symbol
Min.
Typ.
Max.
Unit
Remark
Supply voltage
VDD
10.8
12.0
13.2
V
【Note1】
IDD1
-
440
460
mA
【Note2】
IDD2
-
-
10.0
μA
【Note3,4】
Permissive input ripple voltage
VRP_BL
-
-
200
mVP-P
VDD=+12.0V
High voltage
VIH_BL1
2.6
-
5.5
V
【Note3】VDD=12V
Low voltage
VIL_BL1
-
-
0.4
V
【Note3】VDD=12V
Leak current
ＩIL_XST
-
-
2.0
mA
【Note3】VIH_XST=5.5V
High voltage
VIH_BL2
2.1
-
5.5
V
【Note4】VDD=12V
Low voltage
VIL_BL2
-
-
0.4
V
【Note4】VDD=12V
Leak current
ＩIL_VBR
-
-
2.0
mA
【Note4】 VIH_XST=5.5V
PWM frequency
fPWM
200
-
1,000
Hz
【Note4,5】
PWM duty ratio
DPWM
10
-
100
%
【Note4,5】
Life time
L
-
-
h
【Reference】
【Note6】
Current dissipation
XSTABY
VBR
50,000
(Module)
【N t 1】 On-off
【Note1】
O
ff conditions
diti
for
f supply
l voltage
lt
0.9 VDD
VDD
0.1 VDD
0.9 VDD
t7 t8
0.1 VDD
t9
t10
t7
≦ 200ms
0ms ≦
t8
≦ 1s
0ms ≦
t9
1ms ≦ t10
XSTABY
t11
VBR
PWM
0ms ≦ t11 ≦ 200ms
t12
0ms ≦ t12
t13
ON
Back light
(LED)
20µs ≦
OFF
【Note2】 Current dissipation
OFF
about 300ms
VBR
t14
Typ. value： VDD= +12V、Duty=100%
【Note3】 XSTABY is connected by the pull-down resistor of about 100kΩ.
【Note4】 VBR is connected by the pull-down resistor of about 100kΩ.
【Note5】 PWM
fPWM ＝ 1/t14 、 DPWM=t13/t14
Duty 10% : Min. Luminance
Duty 100% : Max. Luminance
Luminance changes in proportion to the duty ratio.
When the frequency slows, the display fineness might decrease.
【Note6】 Luminance becomes 50% of an initial value. (Ta＝25℃, PWM=100%)
LD-24403B- 9
7．Timing characteristics of input signals
7-1．Timing characteristics
Parameter
Symbol
Min.
Typ.
Max.
Unit
Frequency
1/Tc
35.0
40
42.0
MHz
Horizontal period
TH
890
1056
1395
clock
20.8
26.4
39.9
μs
Effective display
area
THd
800
800
800
clock
Vertical period
TV
628
666
798
line
15.8
17.6
18.5
ms
600
600
600
line
Clock
Enable
signal
Effective display
area
TVd
Remark
【Note1】
【Note1】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.
TH
THd
ENAB
800
1
2
800
DATA
(R,G,B)
Tc
2
1
ENAB
599
TVd
TV
7-2．Input Data Signals and Display Position on the screen
R
G
B
R
G
B
（ 2, 1 ）
（ 1, 1 ）
UP
Position where data is displayed screen（H, V）
D(1,1) D(2,1) D(3,1)
D( 800
,1)
D(1,2) D(2,2)
D(1,3)
D(1,
R G B
600
)
D( 800 , 600)
600
LD-24403B- 10
8．Input Signals, Basic Display Colors and Gray Scale of Each Color
8-1．6 bit input
Gray Scale of Blue
Gray Scale of Green
Gray Scale of Red
Basic Color
Colors &
Gray scale
Data signal
GrayScale
R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
Black
－
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Blue
－
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
Green
－
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Cyan
－
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
Red
－
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Magenta
－
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
Yellow
－
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
White
－
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
↑
GS1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker
GS2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
↑
↓
↓
↓
↓
↓
↓
↓
↓
↓
Brighter
GS61 1
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
↓
GS62 0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Red
GS63 1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
↑
GS1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
Darker
GS2
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
↑
↓
↓
↓
↓
↓
↓
↓
↓
↓
Brighter
GS61 0
0
0
0
0
0
1
0
1
1
1
1
0
0
0
0
0
0
↓
GS62 0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
Green
GS63 0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
↑
GS1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
Darker
GS2
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
↑
↓
↓
↓
↓
↓
↓
↓
↓
↓
Brighter
GS61 0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
1
1
↓
GS62 0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
Blue
GS63 0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0 :Low level voltage
1 :High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of
total 18 bit data signals, the 262,144-color display can be achieved on the screen.
LD-24403B- 11
9．Optical Characteristics
Ta=+25℃, Vcc=＋3.3V
Parameter
Horizontal
Viewing
angle
range
Symbol
Min.
Typ.
Max.
Unit
-
70
-
Deg.
-
50
-
Deg.
-
60
-
Deg.
360
600
-
τr +τd
-
35
-
Wx
0.26
0.310
0.360
Wy
0.285
0.335
0.385
Rx
-
0.570
-
Ry
-
0.325
-
Gx
-
0.336
-
-
0.570
-
θ21,θ22
θ11
Vertical
White Black
CR>10
θ12
Contrast ratio
Response Time
Condition
CR
Chromaticity of
White
Chromaticity of
Red
Chromaticity of
Green
Gy
optimized
angle
θ=0°
Chromaticity of
Blue
Bx
-
0.170
-
By
-
0.170
-
Luminance of white
YL1
315
420
-
-
-
1.33
White Uniformity
Remark
【Note1,2,4】
【Note2,4】
【Note3,4】
ms
【Note4】
cd/m
2
【Note4】
【Note5】
※The measurement shall be executed 30 minutes after lighting at rating.
The optical characteristics shall be measured in a dark room or equivalent state with the method shown
in Fig.2 below.
Photodetector：(EZ-CONTRAST）
400mm
Photodetector
：Response time（BM-5A）
：Contrast/Luminance/Chromaticity（SR-3）
Field=1°
Panel center(θ=0°）
Panel center(θ=0°)
TFT-LCD module
TFT-LCD module
fig.2-1 Measuring method of Viewing angle range.
fig.2-2 Measuring method of contrast, luminance, response time,
and Chromaticity.
Fig.2 Optical characteristics measurement method
LD-24403B- 12
【Note1】Definitions of viewing angle range:
Normal line
θ1 θ21
θ22
θ1
6 O'clock
【Note2】Definition of contrast ratio:
The contrast ratio is defined as the following.
Contrast （CR）＝
Luminance with all pixels white
Luminance with all pixels black
【Note3】Definition of response time:
The response time is defined as the following figure and shall be measured by switching the input signal for
"black" and "white".
Photodetector Output
(Relative Value)
White
White
Black
100%
90%
10%
0%
τd
τr
Ti
【Note4】This shall be measured at center of the screen.
【Note5】Definition of white uniformity:
White uniformity is defined as the following with five measurements.
(①～⑤)
δw =
200
2
Maximum luminance of 5 points(①～⑤).
Minimum luminance of 5 points(①～⑤).
400
600 pixel
3
300
1
5
150
4
450
pixel
LCY-W-12202A- 13
10． Handling Precautions
【Handling Precautions】
a ) Treat LCD module in dustless surroundings. Metal foreign material stuck to the circuit is possible to cause a short.
b ) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist.
c ) Be careful not to give any physical stress onto the circuit and/or the connector of LCD module
when you pull/plug a cable. Physical stress will cause a break or worse connection.
d ) Since the front polarizer is easily damaged, pay attention not to scratch it.
e ) Use N2-blower such as an ionized nitrogen has anti-electrostatic when you blow dusts on Polarizer.
f ) Since a long contact with water may cause discoloration or spots, wipe it with absorbent cotton or other soft
cloth immediately.
g ) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when handling.
Observe all other precautionary requirements in handling components.
h ) Be careful with the edge parts of the module which is made of metal.
i ) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care.
j ) When the panel is broken, don’t touch the glass. Although the panel is difficult to be scattered, touching the
broken part may hurt your hands.
k ) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside
your eye or mouth by mistake.
l ) Don’t touch the circuit and the pattern of the board. If you touch it, the circuit may be broken.
m ) Follow the regulations when LCD module is scrapped. The government you stay may have some regulations
about it.
【Set-Design Precautions】
a ) Notice : Never take to pieces the module , because it will cause failure. Please don't remove the fixed tape,
insulating tape etc. that was pasted on the original module. (except for protection film of the panel)
b ) Protection film is attached to the module surface to prevent it from being scratched .Peel the film off slowly ,
just before the use, with strict attention to electrostatic charges. Blow off 'dust' on the polarizer by using
an ionized nitrogen.
c ) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist.
d ) Connect GND to flame of module to stabilize against EMI and external noise.
e ) When install LCD modules in the cabinet, please tighten with( “torque=0.294±0.02N･m(3.0±0.2kgf･cm)”).
Be sure to confirm it in the same condition as it is installed in your instrument.
f ) Since there is a circuit board in the module back, stress is not added at the time of a design assembly.
Please make it like. If stress is added, there is a possibility that circuit parts may be damaged.
g) It causes an irregular display and the defective indication, etc., when always put constant pressure
on the back of the module. Please do not make the structure to press the back of the module.
h) Be careful of a back light FPC not to pull by force at the time of the connecting to a W-LED driver,
or FPC processing.
LCY-W-12202A- 14
i)
The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist.
j)
Don’t change the volume of LCD module. It is optimized when the shipping. Any change may not meet
the specification.
k) If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity
issue, etc.
Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan.
l) Be sure to follow the absolute maximum rating in the specification. The design should consider the surrounding
temperature, the fluctuating input signal, and tolerance of the electronic parts. Exceeding values is possible to
cause worse characteristic such as burn and/or broken of the parts on LCD module.
m) Be sure to use LCD module within the recommended operating conditions. Operating module out of the
recommended range is not guaranteed even if it is in the absolute maximum rating.
n) Follow the power, signal, and supply voltage sequence which the specification indicates, regarding on-off
input signal after power on of LCD module.
o) According to the using application, power circuit protection is recommended at module failure.
【Operation Precautions】
a ) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is used
under such environment.
b ) When handling LCD modules and assembling them into cabinets, please avoid that long-terms storage in the
environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin,
etc. which generate these gasses, may cause corrosion and discoloration of the modules.
Do not use the LCD module under such environment
environment.
c ) An abnormal display by changing in quality of the polarizing plate might occur regardless of contact or no contact
to the polarizing plate, because of epoxy resin (amine system curing agent) that comes out from the material
and the packaging material used for the set side, the silicon adhesive (dealcoholization system and oxime system),
and the tray blowing agents (azo-compound), etc. Please confirm adaptability with your employed material.
d ) Don’t use polychloroprene (CR) with LCD module. It will generate chlorine gas, which will damage the reliability of
the connection part on LCD panel.
e ) Be careful when using it for long time with fixed pattern display as it may cause accidential image.
Pleave use a screen saver etc., in order to avoid an afterimage.
f ) The LED (Light Emitting Diode) used in this LCD module is very sensitive to temperature change. If it operates
for extremely long time under high temperature, it is possible rapidly to shorten the life time of LED.
In case of such a condition, consult with us.
g) If stored at the temperatures lower than the rated storage temperature, the LC may freeze and it may cause
LCD panel damage. If storage temperature exceeds the specified rating, the molecular orientation of the LC may
change to that of a liquid, and they may not revert to their original state. Store the module in normal room
temperature.
h) Keep LCD module in the range of the specified temperature conditions at all times. Once out of the range,
liquid crystal will lose its characteristics, and it cannot recover.
i)
Nature of dew consideration prevention is necessary when LCD is used for long time under high-temperatur
and high-humidity.
LD-24403B- 15
11．Packing form
a) Piling number of cartons ：
MAX．6
b) Package quantity in one carton：
20pcs
c) Carton size(TYP)：
451mm(W) × 440mm(D)×313mm(H)
d) Total mass of one carton filled with full modules(20pcs)： max 13.5kg
Packing form is shown in Fig 3.
12．Reliability test items
No.
1
6
Test item
High temperature
storage test
Low temperature
strage test
High temperature
& high humidity
operation test
High temperature
operation test
Low temperature
operation test
Vibration test
7
Shock test
2
3
4
5
Conditions
Ambient temperature 80℃ 240H
Remark
【Note1】
Ambient temperature -30℃ 240H
【Note1】
Ambient temperature 40℃、Humidity 95％ RH 240H
（No condensation.）
【Note1】
Panel surface（Active Area) 80℃ 240H
【Note1】
Ambient temperature -30℃ 240H
【Note1】
＜Sin wave＞
Frequency ：10～57Hz／Vibration width (one side) ：0.076mm
：57～500Hz／Gravity：9.8m/s2
Sweep time：11minutes
Test period ：3H（X，Y，Z direction 1H）
Max. gravity：490m/s2 Pulse width：11ms
Direction：±X,±Y,±Z Test period ：1time／1direction
【Note1】
【Note1】
【Note1】 Under the display quality test conditions with normal operation state, these shall be no change
which may affect practical display function. (normal operation state：Temperature:15～35℃,
Humidity:45～75％, Atmospheric pressure:86～106kpa)
LD-24403B- 16
13．Others
13-１．Lot No Label:
Ａ）Module serial label
The label that displays SHARP･Model No.（ LQ104S1LG81）･Lot No. is stuck on the back of the module.
Lot No display method（Figure and alphabet）
SHARP
Model No.
LQ104S1LG81
Production year
(Last digit of dominical year)
Bar Code(Lot No.)
XXXXXXXXXX
Production month (1-9X, Y, Z)
Lot No.
Serial No.
Assembly site code
Discernment code
Ｂ）Backlight serial label
The label that displays the model No. and lot No. for the backlight is stuck on the back of the module.
＊＊＊＊＊＊-＊
Model No.
(Figure and alphabet)
＊＊＊＊＊＊－＊＊
Lot No.
(Figure and alphabet)
13-2．Packing box Label:
The label that displays ①Model number（ LQ104S1LG81） ②Lot number ③Quantity of module is stuck
on the packing box. Moreover, the display of bar code also applies to this.
社内品番：
(4S) LQ104S1LG81
Barcode（①）
Lot No. ： （1T）
2011. 10. 01
＊＊
① Model number（ LQ104S1LG81）
Barcode（②）
Quantity ： （Q）
② Lot number (DATA)
③ Quantity of module
20 pcs
Barcode（③）
ユーザー品番 ：
シャープ物流用ラベルです。
Our management product number might be filled in.
（Example： LQ104S1LG81A etc.）
A right picture is written to the packing box of module for the RoHS restriction.
※ R.C.（RoHs Compliance）means these parts have corresponded with the RoHs directive.
This module corresponds from the first sample to RoHS Directive.
The production country of the figure below is written in the wrapping box.
ＯＲ
13-3． The ozone-depleting substances is not used.
13-4． If any problem occurs in relation to the description of this specification , it shall be resolved
through discussion with spirit of cooperation.
R.C.
LD-24403B- 17
14．Storage conditions
Environmental condition range of storage temperature and humidity
Temperature 0 to 40 degrees Celsius
Relative humidity 95% and below
【Note】Please refer below as a mean value of the environmental conditions.
Summer time temperature 20 to 35 degrees Celsius humidity , 85% and below
Winter time temperature 5 to 15 degrees Celsius humidity , 85% and below
Please maintain within 240 hours of accumulated length of storage time, with conditions of 40 degrees
Celsius and room humidity of 95%.
Direct sun light
Please keep the product in a dark room or cover the product to protect from direct sun light.
Atmospheric condition
Please refrain from keeping the product with possible corrosive gas or volatile flux.
Prevention of dew
Please store the product carton either on a wooden pallet or a stand / rack to prevent dew.
Do not place directly on the floor. In addition, to obtain moderate ventilation in between the pallet’s
top and bottom surfaces, pile the cartons up in a single direction and in order.
Please place the product cartons away from the storage wall.
Storage period
g p
period should be one y
year.
Within above mentioned conditions,, maximum storage
LD-24403B- 18
Fig. 1 ： LQ104S1LG81 ＯＵＴＬＩＮＥ ＤＩＭＥＮＳＩＯＮＳ
LD-24403B- 19
Fig.3 : PACKING FORM
工商网监
湘ICP备2023018690号
