LQ104V1DG62

LD-20209A-1 1. Application This specification applies to color 10.4VGA TFT-LCD module, LQ104V1DG62. These specification sheets are the proprietary product of SHARP CORPORATION (”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. The device listed in these technical literature sheets was designed and manufactured for use in general electronic equipment. In case of using the device for applications such as control and safety equipment for transportation (conrrols of aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken. Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for life support. SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. Confirm "12. Handling Precautions " item when you use the device. Contact and consult with a SHARP sales representative for any questions about this device. 2. Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit and power supply circuit and a White-LED backlight unit. Graphics and texts can be displayed on a 640×3×480 dots panel with 262,144 colors by supplying 18 bit data signal (6bit/color), four timing signals, +3.3V/5.0V DC supply voltage for TFT-LCD panel driving and supply voltage for backlight. The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation type. Therefore, this module is also suitable for the multimedia use. Viewing angle is 6 o’clock direction. This module is the type of wide viewing angle, superhigh brightness (550cd/m2) and high contrast (600:1). The LED Backlight driving DC/DC converter and the cable are not built in this LCD module. LD-20209A-2 3. Outline specification. Parameter Specifications Diagonal Unit Display size 26 (10.4") Active area 211.2(H)×158.4(V) mm Pixel format 640(H)×480(V) pixel (1 pixel=R+G+B dots) Number of colors (Number of gray scale level) cm - 262, 144 colors (64 gray scales per color) Pixel pitch 0.330(H)×0.330(V) mm Pixel configuration R,G,B vertical stripe - Display mode Normally white - Unit outline dimensions *1 246.5(W)×179.4(H)×Max.12.5(D) Mass 580(max) g Surface treatment Anti-glare and hard-coating 3H - mm *1: Note: excluding back light cables (The backlight cable is not attached to the LCD unit.) The thickness of module (D) doesn’t contain the projection. Outline dimensions is shown in Fig.1 LD-20209A-3 4. Input Terminals 4-1. TFT-LCD panel driving CN1 Used connector: DF9MA-31P-1V(32) 1 (Hirose Electric Co., Ltd.) 31 30 2 CN1 pin arrangement from module surface (Transparent view) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Symbol GND CK Hsync Vsync GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND ENAB Vcc Vcc R/L U/D Corresponding connector: DF9-31S-1V(32), DF9A-31S-1V(32), DF9B-31S-1V(32), DF9C-31S-1V(32) (Hirose Electric Co., Ltd.) （※）Please do not use it besides corresponding conector Function Remark Clock signal for sampling each data signal Horizontal synchronous signal [Note1] Vertical synchronous signal [Note1] RED data signal(LSB) RED data signal RED data signal RED data signal RED data signal RED data signal(MSB) GREEN data signal(LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal(MSB) BLUE data signal(LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal(MSB) Signal to settle the horizontal display position [Note2] +3.3V / +5.0V power supply +3.3V / +5.0V power supply Horizontal display mode select signal [Note3] Vertical display mode select signal [Note4] ※The shielding case is connected with GND. [Note1] The polarity of both synchronous signals are negative. [Note2] The horizontal display start timing is settled in accordance with a rising timing of ENAB signal. In case ENAB is fixed "Low", the horizontal start timing is determined as described in 8-2. Don't keep ENAB “High" during operation. LD-20209A-4 [Note 3],[Note 4] R/L = High, U/D = Low R/L = Low, U/D = Low connector R/L = High, U/D = High connector R/L = Low, U/D = High connector connector 4-2. Backlight driving CN2 Used connector : SM06B-SRSS-TB(LF)(SN) Pin no. 1 2 3 4 5 6 Corresponding connector : SHR-06V-S-B (JST) symbol function +ch3 Power supply for LED (Ch3 High voltage side) +ch2 Power supply for LED (Ch2 High voltage side) +ch1 Power supply for LED (Ch1 High voltage side) - ch1 Power supply for LED (Ch1 Low voltage side) - ch2 Power supply for LED (Ch2 Low voltage side) - ch3 Power supply for LED (Ch3 Low voltage side) 5. Absolute Maximum Ratings Parameter Input voltage Lamp input current supply voltage Storage temperature Operating temperature Symbol VI IL Vcc Tstg Topa (JST) Condition Ta=25 oC Ta=25 oC Panel surface Ratings -0.3 to Vcc+0.3 350 0 to +6.0 -30 to +80 -30 to +80 [Note1] CK,R0∼R5,G0∼G5,B0∼B5,Hsync,Vsync,ENAB,R/L,U/D [Note2] Humidity: 95%RH Max. at Ta≦40 oC. Maximum wet-bulb temperature at 39 oC or less at Ta>40 oC. No condensation. Unit V mA V o C o C Remark [Note1] [Note2] LD-20209A-5 6. Recommended operation condition Parameter Symbol VI Input voltage VCC Supply voltage Ambient temperature Topa Min. 0 Typ. Max. Vcc ＋3.0 -30 +3.3/+5.0 ＋5.5 +80 Unit Ｖ Ｖ ℃ Remark [Note1] [Note2] [Note3], [Note4] [Note1]CK,R0∼R5,G0∼G5,B0∼B5,Hsync,Vsync,ENAB,R/L,U/D [Note2] Vcc-turn-on conditions 0