LQ121S1LG61

PRODUCT SPECIFICATIONS AVC Liquid Crystal Displays Group LQ121S1LG61 TFT-LCD Module Spec. Issue Date: Jan. 27, 2006 No: LD-18123A LD18123A-1 1. Application This specification applies to color TFT-LCD module, LQ121S1LG61 These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. The device listed in these specification sheets was designed and manufactured for use in general electronic equipment. In case of using the device for applications such as control and safety equipment for transportation (aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken. Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for life support. SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. Contact and consult with a SHARP sales representative for any questions about this device. LD18123A-2 2. Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a backlight unit. Graphics and texts can be displayed on a 800 X 3 X 600 dots panel with 262,144 colors by using LVDS (Low Voltage Differential Signaling) system for interface and supplying +3.3Vor+5.0V DC supply voltage for TFT-LCD panel driving. This module is super-high brightness (450cd/m^2) and high contrast (600:1). This module is the type of wide viewingangle the viewing angle is 6 o’clock direction. Backlight-driving DC/AC inverter is not built in this module. 3. Outline Specifications Parameter Display size Active area Pixel format 31 (12.1") Specifications Diagonal Unit cm mm pixel 246.0 (H ) X 184.5 (V) 800 (H ) X 600 (V) (1 pixel=R+G+B dots) Number of colors (Number of gray scale level) Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment [Note] excluding backlight cables. 262, 144 colors (64 gray scales per color) 0.3075 (H) X 0.3075 (V) R,G,B vertical stripe Normally white 276.0(W)×209.0(H)×Max.11.0 (D) *Outline dimensions is shown in Fig.1 Max. 800 Anti-glare and hard-coating 3H mm mm g LD18123A-3 4. Input Terminals 4-1. TFT-LCD panel driving CN1 (LVDS signals , +3.3V / +5.0V DC power supply and Contorol signal) Corresponding connector:FI-SE20ME (JAE) or FI-S20S (JAE) Pin No. Symbol Function Remark 1 VCC +3.3V / +5.0V power supply 2 VCC +3.3V / +5.0V power supply 3 GND 4 GND 5 RXIN0Differential data input, CH0 (negative) LVDS signal 6 RXIN0+ Differential data input, CH0 (positive) LVDS signal 7 GND 8 RXIN1Differential data input, CH1 (negative) LVDS signal 9 RXIN1+ Differential data input, CH1 (positive) LVDS signal 10 GND 11 RXIN2Differential data input, CH2 (negative) LVDS signal 12 RXIN2+ Differential data input, CH2 (positive) LVDS signal 13 GND 14 RXCLK INDifferential clock input (negative) LVDS signal 15 RXCLK IN+ Differential clock input (positive) LVDS signal 16 GND 17 R/L Horizontal display mode select signal [Note1] 18 U/D Vertical display mode select signal [Note2] 19 GND 20 GND [Note ] To obtain the proper relation between LVDS signals and actual digital data signals, the digital signals should be inputted into the transmitter as described in the nextsection, 4-2. [Note ] The shielding case is connected with signal GND. [Note 1],[Note 2] R/L = High, U/D = Low R/L = Low, U/D = Low R/L = High, U/D = High R/L = Low, U/D = High LD18123A-4 4-2 LVDS Interface block diagram Using receiver：Single LVDS interface, which equals THC63LVDF64A(THine),contained in a control IC Corresponding Transmitter：DS90C363, DS90C363A, DS90C383, DS90C383A(National semiconductor), THC63LVDF63A,THC63LVDM63A(THine), SN75LVDS84(Ti) （System Side） (TFT-LCD Side) LVDS Receiver RxOUT0∼5 RXIN0- (5pin) 100Ω ６ ６ ６ Controller R0∼R5 G0∼G5 B0∼B5 Hsync Vsync ENAB CLK ６ LVDS Transmitter TxIN 0∼ 5 ６ Digital Signal → LVDS Signal TxIN 6∼11 ６ RXIN0+ (6pin) RXIN1- (8pin) 100Ω LVDS Signal →Digital Signal R0∼R5 G0∼G5 B0∼B5 Hsync Vsync ENAB CK RxOUT6∼11 RxOUT12∼17 RxOUT18 RxOUT19 RxOUT20 RxCLK OUT TxIN12∼17 TxIN18 TxIN19 TxIN20 TxCLK IN 100Ω RXIN1+ (9pin) RXIN2- (11pin) 100Ω 100Ω RXIN2+ (12pin) 100Ω RXCLKIN- (14pin) PLL 100Ω RXCLKIN+ (15pin) 100Ω PLL R/L U/D R/L(17pin) U/D(18pin) 10KΩ 100Ω 100Ω R/L U/D 10KΩ VCC VCC(1,2pin) LD18123A-4 ＶＣＣ 10uF GND GND(3,4,7,10,13,16,19,20pin) GND LD18123A-5 [Note ] Data Mapping 1 cycle RXCLKIN-+/- RXIN0+/- R1 R0 G0 R5 R4 R3 R2 R1 R0 G0 RXIN1+/- G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 RXIN12/- B3 B2 DE VS HS B5 B4 B3 B2 DE 4-3. Backlight driving CN2 ,CN3 Used connector : BHR-02(8.0)VS-1N (JST) Corresponding connector : SM02(8.0)B-BHS-1-TB(LF)(SN) or -1N-TB(LF)(SN) (JST) Pin no. symbol function Color of FL cable 1 VHIGH Power supply for lamp （Pink／Blue） (High voltage side) 2 VLOW Power supply for lamp （White／Gray） (Low voltage side) 5. Absolute Maximum Ratings Parameter Symbol +3.3V / +5.0V Vcc supply voltage Input voltage VI1 Condition Ta=25 oC Ta=25oC Pin name Vcc RXINi-/+(i= 0,1,2) RXCLK IN-/+ R/L , U/D - Ratings 0 to + 6.0 Unit V Remark VI2 Ta=25oC Lamp input voltage VHIGH Storage temperature Tstg Operating temperature Topa Panel surface [Note1] Humidity: 95%RH Max. at Ta=40 oC. No condensation. 6.Recommended operation condition Symbol Parameter Supply voltage LVDS Signals Input voltage Ambient temperature Vcc VL VI Topa -0.3 to Vcc+0.3 V -0.3 to 3.3V V -0.3 to Vcc+0.3 V 1800 Vrms o -30 to +80 C o -30 to +80 C Vcc