LQ181E1LW31

LQ181E1LW31 TFT-LCD Module (Model Number: LQ181E1LW31) Specifications Spec No.: LD-13Z04 Dated: May 29, 2002 PREPARED BY : DATE SPEC No. LD-13Z04 FILE No. ISSUE : May.27.2002 APPROVED BY : DATE AVC LCD DEVELOPMENT GROUP SHARP CORPORATION PAGE : 22 pages APPLICABLE GROUP AVC Liquid Crystal Display SPECIFICATION Group DEVICE SPECIFICATION TFT-LCD Module MODEL No. LQ181E1LW31 □ CUSTOMER'S APPROVAL DATE BY PRESENTED BY M.TAKEDA Development General Manager Development Engineering Department 2 AVC LIQUID CRYSTAL DISPLAY Division AVC LIQUID CRYSTAL DISPLAY GROUP SHARP CORPORATION RECORDS OF REVISION LQ181E1LW31 REVISED SPEC No. LD-13Z04 DATE May.27.2002 No. - PAGE - SUMMARY - NOTE 1st Issue LD-13Z04-1 1. Application This specification applies to the color 18.1 SXGA TFT-LCD module LQ181E1LW31. These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. The device listed in these specification sheets was designed and manufactured for use in OA equipment. In case of using the device for applications such as control and safety equipment for transportation(aircraft, trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken. Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment for life support. SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. Contact and consult with a SHARP sales representative for any questions about this device. 2. Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit. Graphics and texts can be displayed on a 1280×3×1024 dots panel with about 16 million colors (8 bit) by using LVDS (Low Voltage Differential Signaling) to interface and supplying +12 DC supply voltages for TFT-LCD panel driving and supply voltage for backlight. It is a wide viewing-angle-module using SHARP original technology. Backlight-driving DC/AC inverter is not built in this module. LD-13Z04-2 3. Mechanical Specifications Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment Specifications 46 (Diagonal) 18.1 (Diagonal) 359.0 (H)×287.2 (V) 1280 (H)×1024 (V) (1 pixel=R+G+B dots) 0.2805 (H) × 0.2805 (V) R,G,B vertical stripe Normally Black 389 (W)×317.2 (H)×27.5(D) MAX 3.5 Anti-glare and hard-coating 2H mm kg mm Unit cm Inch mm Pixel *1.Note: excluding back light cables. The thickness of module (D) doesn’t contain the projection. Outline dimensions are shown in Fig.1. LD-13Z04-3 4. Input Terminals 4-1. TFT-LCD panel driving CN1 (Interface signals and +12VDC power supply) Using connector ：FI-SE30P-HF (Japan Aviation Electronics Ind.,Ltd.) Mating connector ：FI-S30S (Japan Aviation Electronics Ind.,Ltd.) Pin No. Symbol Function 1 Vcc +12V　Power Supply 2 Vcc +12V　Power Supply 3 Vcc +12V　Power Supply 4 GND GND GND 5 GND GND 6 GND 7 SELLVDS Select LVDS data order 【Note1】 NC 8 NC GND 9 GND Positive (+) LVDS differential data input (B port) 10 RxBIN3+ Negative (-) LVDS differential data input (B port) 11 RxBIN312 RxBCLKIN+ Positive (+) LVDS differential clock input (B port) 13 RxBCLKIN- Negative (-) LVDS differential clock input (B port) Positive (+) LVDS differential data input (B port) 14 RxBIN2+ Negative (-) LVDS differential data input (B port) 15 RxBIN2Positive (+) LVDS differential data input (B port) 16 RxBIN1+ Negative (-) LVDS differential data input (B port) 17 RxBIN1Positive (+) LVDS differential data input (B port) 18 RxBIN0+ Negative (-) LVDS differential data input (B port) 19 RxBIN0Positive (+) LVDS differential data input (A port) 20 RxAIN3+ Negative (-) LVDS differential data input (A port) 21 RxAIN322 RxACLKIN+ Positive (+) LVDS differential clock input (A port) 23 RxACLKIN- Negative (-) LVDS differential clock input (A port) Positive (+) LVDS differential data input (A port) 24 RxAIN2+ Negative (-) LVDS differential data input (A port) 25 RxAIN2Positive (+) LVDS differential data input (A port) 26 RxAIN1+ Negative (-) LVDS differential data input (A port) 27 RxAIN1Positive (+) LVDS differential data input (A port) 28 RxAIN0+ Negative (-) LVDS differential data input (A port) 29 RxAIN0GND 30 GND Remark 3.3V C-MOS Pull Up LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LVDS LD-13Z04-4 【Note1】SELLVDS(Thine:THC63LVDM83A) Transmitter Pin No Data 51 TA0 52 TA1 54 TA2 55 TA3 56 TA4 3 TA5 4 TA6 6 TB0 7 TB1 11 TB2 12 TB3 14 TB4 15 TB5 19 TB6 20 TC0 22 TC1 23 TC2 24 TC3 27 TC4 28 TC5 30 TC6 50 TD0 2 TD1 8 TD2 10 TD3 16 TD4 18 TD5 25 TD6 =L(GND) R0(LSB) R1 R2 R3 R4 R5 G0(LSB) G1 G2 G3 G4 G5 B0(LSB) B1 B2 B3 B4 B5 NC (RSV1) DE R6 R7(MSB) G6 G7(MSB) B6 B7(MSB) (NA) SELLVDS =H(3.3V) or Open R2 R3 R4 R5 R6 R7(MSB) G2 G3 G4 G5 G6 G7(MSB) B2 B3 B4 B5 B6 B7(MSB) NC (RSV1) DE R0(LSB) R1 G0(LSB) G1 B0(LSB) B1 (NA) LD-13Z04-5 SELLVDS= Low(GND) 1 cycle CKAIN+ CKAIN- RAIN0+ RAIN0RA1 RA0 GA0 RA5 RA4 RA3 RA2 RA1 RA0 GA0 RAIN1+ RAIN1GA2 GA1 BA1 BA0 GA5 GA4 GA3 GA2 GA1 BA1 RAIN2+ RAIN2BA3 BA2 DE NA NA BA5 BA4 BA3 BA2 DE RAIN3+ RAIN3RA7 RA6 NA BA7 BA6 GA7 GA6 RA7 RA6 NA Tcsq CKBIN- CKBIN+ RBIN0+ RBIN0RB1 RB0 GB0 RB5 RB4 RB3 RB2 RB1 RB0 GB0 RBIN1+ RBIN1GB2 GB1 BB1 BB0 GB5 GB4 GB3 GB2 GB1 BB1 RBIN2+ RBIN2BB3 BB2 DE RSV1 NA BB5 BB4 BB3 BB2 DE RBIN3+ RBIN3RB7 RB6 NA BB7 BB6 GB7 GB6 RB7 RB6 NA DE: Display Enable RSV1: Reserve (Fixed GND) NA: Not Available LD-13Z04-6 SELLVDS= High(3.3V) or Open 1 cycle CKAIN+ CKAIN- RAIN0+ RAIN0RA3 RA2 GA2 RA7 RA6 RA5 RA4 RA3 RA2 GA2 RAIN1+ RAIN1GA4 GA3 BA3 BA2 GA7 GA6 GA5 GA4 GA3 BA3 RAIN2+ RAIN2BA5 BA4 DE NA NA BA7 BA6 BA5 BA4 DE RAIN3+ RAIN3RA1 RA0 NA BA1 BA0 GA1 GA0 RA1 RA0 NA Tcsq CKBIN- CKBIN+ RBIN0+ RBIN0RB3 RB2 GB2 RB7 RB6 RB5 RB4 RB3 RB2 GB2 RBIN1+ RBIN1GB4 GB3 BB3 BB2 GB7 GB6 GB5 GB4 GB3 BB3 RBIN2+ RBIN2BB5 BB4 DE RSV1 NA BB7 BB6 BB5 BB4 DEB RBIN3+ RBIN3RB1 RB0 NA BB1 BB0 GB1 GB0 RB1 RB0 NA DE: Display Enable RSV1: Reserve (Fixed GND) NA: Not Available LD-13Z04-7 4-2 Interface block diagram Using receiver：Contained in a control IC. Corresponding Transmitter：THC63LVDM83A(THine electronics),DS90C383,DS90C383A(National semiconductor) （Computer side） G10～G17 R10～R17 B10～B17 8 8 8 (TFT-LCD side) RxAIN0+(28) RxAIN0-(29) RxAIN1+(26) 8 8 8 R10～R17 G10～G17 B10～B17 TTL → LVDS (HSYC) (VSYC) ENAB RxAIN2+(24) RxAIN2-(25) RxAIN3+(20) RxAIN3-(21) LVDS → TTL RxAIN1-(27) ENAB RxACLKIN+(22) CLK A Port B Port R20～R27 G20～G27 B20～B27 8 8 8 PLL RxACLKIN-(23) PLL CK RxBIN0+(18) RxBIN0-(19) 8 8 R20～R27 G20～G27 B20～B27 RxBIN1+(16) 8 TTL → LVDS TxIN18~20 RxBIN2+(14) RxBIN2-(15) RxBIN3+(10) RxBIN3-(11) RxBCLKIN+(12) PLL RxBCLKIN-(13) PLL Fig.2 Interface block diagram LVDS → TTL RxBIN1-(17) Internal circuits Controller LD-13Z04-9 6. Electrical Characteristics 6-1. TFT-LCD panel driving Parameter Supply voltage Current dissipation Symbol Vcc Icc VRF IIL IIH Min. +11.4 Typ. +12.0 350 Max. +12.6 600 100 10 10 Unit V mA mVp-p µA µA VI=GND VI=Vcc Ta=25℃ Remark 【Note1】 【Note2】 Vcc Permissive input ripple voltage Input current (Low) Input current (High) 【Note1】 1) On-off sequences of Vcc and data 0 < t1 ≤ 60ms 0 < t2 ≤ 10ms 0 ≤ t3 ≤ 1s t4 ≥ 100ms 2) Dip conditions for supply voltage Vmin=11.4V,Vt=9.6V i) Vt ≤ Vcc < Vmin td ≤ 20ms ii) Vcc < Vt This case is described below *1. Vcc 10.8V 10.8V Vcc LVDS Data 1.0V 1.0V LVDS Data t3 t4 t1 t2 Vcc Vt Vmin td *1 The LCD module shuts down when VccPLASTIC LIGHT GUIDE:PMMA< 7) Cold cathode fluorescent lamp in LCD PANEL contains a small amount of mercury, Please follow local ordinances or regulations for disposal. (put on the back of the module. :Size: 63×14mm ) COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS A SMALL AMOUNT OF MERCURY,PLEASE FOLLOW LOCAL ORDINANCES OR REGULATION FOR DISPOSAL 当該液晶ディスプレイパネルは蛍光管が組み込まれていますので、地方自 冶体の条例、または、規則に従って廃棄ください。 8) When any question or issue occurs , it shall be solved by mutual discussion. 14. Carton storage condition Temperature Humidity 0℃ to 40℃ 95%RH or less : 5℃ to 15℃ , 85%RH or less (winter) ・the total storage time (40℃,95%RH) : 240H or less Sunlight Atmosphere Notes Be sure to shelter a product from the direct sunlight. Harmful gas, such as acid and alkali which bites electronic components and/or wires, must not be detected. Be sure to put cartons on palette or base, don’t put it on floor, and store them with removing from wall Please take care of ventilation in storehouse and around cartons, and control changing temperature is within limits of natural environment Storage period 1 year Reference condition : 20℃ to 35℃ , 85%RH or less (summer) SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA EUROPE JAPAN SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 Fast Info: (1) 800-833-9437 www.sharpsma.com SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE SHARP Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com TAIWAN KOREA SHARP Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328 SHARP Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855 SHARP Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819 CHINA HONG KONG SHARP Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp SHARP-ROXY (Hong Kong) Ltd. 3rd Business Division, 17/F, Admiralty Centre, Tower 1 18 Harcourt Road, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 13B1, Tower C, Electronics Science & Technology Building Shen Nan Zhong Road Shenzhen, P.R. China Phone: (86) 755-3273731 Fax: (86) 755-3273735