LS013B4DN01

Technical Document LCD Specification LCD Group LS013B4DN01 LCD Module Preliminary Product Specification April 2009 96 × 96 Silver Reflective PNLC Memory LCD Module featuring Zebra (elastomeric) connector, 50% reflectivity with 10:1 contrast. No. Date LCY-12T09302A April. 24th 2009 TECHNICAL LITERATURE For TFT-LCD Module Model No. LS013B4DN01 Notice The technical Literature is subject to change without any prior notice for the purpose of product improvement. Please contact Sharp or its representative before designing your product based on this literature. Mobile Liquid Crystal Display Group SHARP CORPORATION SPEC No. MODEL No. PAGE LCY-12T09302A LS013B4DN01 1 NOTICE ○ These specification sheets are the proprietary product of SHARP CORPORATION ("SHARP") and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. ○ The application examples in these specification sheets are provided to explain the representative applications of the device and are not intended to guarantee any industrial property right or other rights or license you to use them. SHARP assumes no responsibility for any problems related to any industrial property right of a third party resulting from the use of the device. ○SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when in using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for use in general electronic equipment designs, such as: ・Personal computers ・Office automation ・Telecommunication equipment ・Industrial control ・Consumer electronics ・Test and measurement equipment ・Audio visual and multimedia equipment The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: ・Transportation control and safety equipment(i.e.,aircraft,trains,automobiles,etc.) ・Traffic signals ・Alarm equipment ○ ・Gas leakage sensor breakers ・Various safety devices etc. SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: ・Nuclear power control equipment ・Military and space applications ・Medical equipment for life support ○ SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. ○ Contact and consult with a SHARP sales representative for any questions about this device. . SPEC No. MODEL No. PAGE LCY-12T09302A LS013B4DN01 2 [For handling and system design] (1) It is recommended to handle LCD panel with carefully, since this LCD panel is made of thin glass, dropping the module or banging it against hard objects may cause cracks or fragmentation. (2) Do not scratch the surface of the UV protection film as it is easily damaged. (3) Water droplets on the UV protection film must be wiped off immediately as they may cause color changes, or other defects if remained for a long time. (4) If the cleaning of the surface of the LCD panel is necessary, wipe it swiftly with cotton or other soft cloth. Do not use organic solvents as it damages the UV protection film. (5) Do not hold or touch the part of single glass of LCD panel which has electric connection area, as electric circuits in LCD panel may be damaged. (6) Hold LCD with very carefully when placing LCD module into the system housing. (7) LCD panel is susceptible to mechanical stress and even the slightest stress will cause a color change in background. So make sure the LCD panel is placed on flat plane without any continuous twisting, bending or pushing stress. (8) When carrying the LCD module, place it on the tray to protect from mechanical damage. It is recommended to use the conductive trays to protect LCD panel from electrostatic discharge. Certain materials such as epoxy resin (amine’s hardener) or silicone adhesive agent (de-alcohol or de-oxym) emits gas to which the UV protection film reacts (color change). Check carefully that gas from materials used in system housing or packaging do not hart the UV protection film. (9)Do not apply excessive stress or pressure to LCD module. Do not to use chloroprene rubber as it may affect on the reliability of the electrical interconnection. (10) As this LCD module contains components sensitive to electrostatic discharge, more than 200V, be sure to follow the instructions in below. ① Operators Operators must wear anti-static wears to prevent electrostatic charge up to and discharge from human body. ② Equipment and containers Process equipment such as conveyer, soldering iron, working bench and containers may possibly generate electrostatic charge up and discharge. Equipment must be grounded through 100Mohms resistance. Use ion blower. ③ Floor Floor is an important part to leak static electricity which is generated from human body or equipment. There is a possibility that the static electricity is charged to them without leakage in case of insulating floor, so the electrostatic earth should be lower than the 1×108Ω. ④Humidity Proper humidity of working room may reduce the risk of electrostatic charge up and discharge. Humidity should be kept over 50% all the time. ⑤Transportation/storage Storage materials must be anti-static to prevent causing electrostatic discharge. ⑥Others (11) Protective film is attached on the surface of the UV protection film on LCD panel to prevent scratches or other damages. When removing this protective film, remove it slowly under proper anti-ESD control such as ion blower. SPEC No. MODEL No. PAGE LCY-12T09302A LS013B4DN01 3 [For operating LCD module] (1) Do not operate the LCD panel under outside of electrical specification. Otherwise LCD panel may be damaged. (2) Do not operate the LCD panel under outside of specified driving timing chart. Otherwise LCD panel may not have proper picture quality. (3) A still image should be displayed less than two hours, if it is necessary to display still image longer than two hour, display image data must be refreshed in order to avoid sticking image on LCD panel. [Precautions for Storage] (1) Do not expose the LCD module to direct sunlight or strong ultraviolet light for long periods. Store in a dark place. (2) The liquid crystal material will solidify if stored below the rated storage temperature and will become an isotropic liquid if stored above the rated storage temperature, and may not retain its original properties. Only store the module at normal temperature and humidity (25±5°C,60±10%RH) in order to avoid exposing the UV protection film to chronic humidity. (3) Keeping Method a. Don't keeping under the direct sunlight. b. Keeping in the tray under the dark place. SPEC No. MODEL No. PAGE LCY-12T09302A [Other Notice] LS013B4DN01 4 (1) Do not operate or store the LCD module under outside of specified environmental conditions. (2) As electrical impedance of power supply lines (VDD-VSS) are low when LCD module is working, place the de-coupling capacitor near by LCD module as close as possible. (3) Although the LCD panel has the UV protection film on the LCD panel surface, just in case, do not expose the LCD module to direct sunlight or strong ultraviolet light for long periods. (4) Do not disassemble the LCD module as it may cause permanent damage. (5) Since the liquid crystal is injurious, do not put it into the eyes or mouth. When liquid crystal sticks to hands, feet or clothes, wash it out immediately with soap. (6) This LCD module does not contain nor use any ODS (1,1,1-Trichloroethane, CCL4) in all materials used, in all production processes. (7) Observe all other precautionary requirements in handling general electronic components. [Precautions for Discarding Liquid Crystal Modules] LCD panel: Dispose of as glass waste. This LCD module contains no harmful substances. The liquid crystal panel contains no dangerous or harmful substances. The liquid crystal panel only contains an extremely small amount of liquid crystal (approx.100mg) and therefore it will not leak even if the panel should break. -Its median lethal dose (LD50) is greater than 2,000 mg/kg and a mutagenetic (Aims test: negative) material is employed. SPEC No. MODEL No. PAGE LCY-12T09302A Contents LS013B4DN01 5 1. Outline ･･･････････････････････････････････････････････････････････････････････････P6 2. Characteristics ････････････････････････････････････････････････････････････････････P6 3.Mechanical Specification･････････････････････････････････････････････････････････････P6 4.Input terminal specification･･･････････････････････････････････････････････････････････P7 5.Absolute Maximum Rating･･･････････････････････････････････････････････････････････P8 6.Electrical Specification･･･････････････････････････････････････････････････････････････P8 7.Optical Chracteristics････････････････････････････････････････････････････････････････P18 8.LCD Module Outline Dimensions･････････････････････････････････････････････････････P20 9.External capacitor････････････････････････････････････････････････････････････････････P21 10.External power supply･･･････････････････････････････････････････････････････････････P22 11.Zebra Connector････････････････････････････････････････････････････････････････････P23 12.Packaging ･････････････････････････････････････････････････････････････････････････P24 13.Reliability test ････････････････････････････････････････････････････････････････････P26 SPEC No. MODEL No. PAGE LCY-12T09302A LS013B4DN01 6 1.Outline This TFT-LCD module is a reflective active matrix memory liquid crystal display module with CG silicone thin film transistor. Module outline is indicated in Table 8-1. 2.Characteristics ・Reflective panel of white and black with aspect ratio of 1:1 ・1.35” screen has 96x 96 resolusion.( 9216 pixels stripe array) ・Display control by serial data signal communication. ・Arbitrary line data renewable. ・1bit internal memory for data storage within the panel. ・Thin, light-weight and compact module with monolithic technology. ・Super low power consumption TFT panel. ・Zebra connecter 3．Mechanical Specification Table 3-1 Item Screen size Viewing Area Dot configuration Dot pitch Pixel Array Outline Dimension Mass Surface Hardness 1.35 24 (H) × 24 (V) 96 (H) × 96 (V) Specification Inch mm Dot mm mm g Pencil hardness unit 0.252 (H) × 0.252 (V) Stripe Array 28.2 (W) × 32.34 (H) × 1.4 (D) 3.6 (TYP） 3H （Note） Detail dimension and tolerance are shown in fig. 8-1 SPEC No. MODEL No. PAGE LCY-12T09302A 4．Input terminal names and functions Table4-1 Terminal Symbol I／O 1 TEST1 2 TEST2 3 4 5 6 7 8 9 10 11 12 13 14 SCLK SI SCS EXTCOMIN DISP VDDA VDD EXTMODE VSS VSSA TEST3 TEST4 INPUT INPUT INPUT INPUT INPUT POWER POWER INPUT POWER POWER - LS013B4DN01 7 Function Test terminal Test terminal Serial clock signal Serial Data input signal Chip select signal External COM inversion signal input (H: enable) Display ON/OFF signal Power supply (Analog) Power supply (Digital) COM inversion select terminal GND(Digital) GND(Analog) Test terminal Test terminal Remark 【Remark4-1】 【Remark4-1】 【Remark4-3】 【Remark4-2】 【Remark4-1】 【Remark4-1】 【Remark4-1】TEST terminal: OPEN these test terminals. 【Remark4-2】When it’s ”H”, EXTCOMIN signal is enable. And when it’s ”L” ,serial input flag is enable. “H”mode; connect the EXTMODE toVDD, ”L” mode; connect the EXTMODE to VSS. 【Remark4-3】The display ON/OFF signal is only for display. Data in the memory will be saved at the time of ON/OFF. When it’s ”H”, data in the memory will display, when it’s ”L”, white color will diaplay and data in the memory will be saved. 4-2）Recommended circuit; SPEC No. MODEL No. PAGE LCY-12T09302A 5．Absolute maximum rating Table5-1 （GND＝0V） Item Power supply voltage Analog Logic Symbol VDDA VDD MIN. -0.3 -0.3 MAX. ＋5.8 ＋5.8 VDD -0.3 Tstg (at Topr1 -30 -20 ＋80 ＋70 Unit V V V V ℃ ℃ LS013B4DN01 8 Remark [Remark5-1] [Remark5-2] [Remark5-3,4] [Remark5-5] Input signal voltage(high) Input signal voltage(low) Strage Temperature Operation Temperature panel surface) [Remark5-1] Applies to EXTMODE. [Remark5-2] Applies to SCLK, SI, SCS, DISP, EXTCOMIN. [Remark5-3] Do not exceed this temperature in any parts of module. [Remark5-4] Maximum wet bulb temperature is 57℃ or lower. No condensation is allowed. Cndensation will cause electeical leak and may cause the module to not meet this specification. [Remark5-5] Operating temperature is the temperature that guarantees only the operation. For contrast, response time, and other display quality determination, use Ta＝＋25℃. 6．Electrical characteristics 6-1）TFT LCD panel Drive Table6-1 Recommended operating Condition Item Power supply Input signal voltage Input leak current Analog Logic Hi Lo Hi Lo symbol VDDA VDD VIH VIL IOH IOL MIN. ＋4.8 ＋4.8 ＋2.70 VSS - VSS(GND)＝0V、Ta＝＋25℃ TYP. ＋5.0 ＋5.0 ＋3.00 VSS MAX. ＋5.5 ＋5.5 ※VDD VSS+0.15 TBD TBD Unit V V V V uA uA [Remark6-2] VI=3V [Remark6-2] VI=0V [Remark6-1] [Remark6-2] Remark ※ Lower 3V is recommended, and it’s lower than the VDD voltage. [Remark6-1] Applies to EXTMODE＝”H” [Remark6-2] Applies to SCLK, SI, SCS, DISP, EXTCOMIN. SPEC No. MODEL No. PAGE LCY-12T09302A 6-2）Power supply sequence LS013B4DN01 9 [On sequence]　 * All on start up System ①5V start up ②Initializes memory data within pixel T2 : more than 1V 　 Initialize with D2 "all clear flag" or display all white. ③To cancel latch initialization for TCOM. T3 : more than 30us The period of canceling COM latch circuit for initialization by using DISP signal. ④TCOM polarity initialization T4: more than 30us 　 The period of initialization for TCOM polarity by EXTCOMIN signal. [Normal operation] Duration of normal driving. [Off sequence] ⑤Initializes memory data within pixel ⑥The period of initialization for VA, VB, and VCOM ⑦5V shut down On Sequence Normal operation T5 : more than 1V T6 : more than 1V Off Sequence ① T1 ② T2 ③※1 ④※1 T3 T4 ⑤ T5 ⑥ T6 ⑦ T7 GND VDD/VDDA (5V) DISP EXTCOMIN SCS Others GND GND GND GND Normal operation ※2 ※2 Normal operation Normal operation ※2 ※2 GND GND GND GND GND ※Detail description for signal timing is shown the digital timing chart and the AC timing chart. ※1　The order of ③ and ④ can be set as being reversed, in this case, TCOM polarity inversion timing which can be controlled by EXTCOMIN doesn't work during DISP="L". 　 ※2　Setup value for initialization of data within pixel memory To refer the timing chart of all clear mode section 6-5-4. [Remark] Precaustions at ehte time of power on and power off. Remark 1)When power on , VDDand VDDA are same timem or VDD should be faster than the VDDA. Remark 2) When power off, VDD and VDDA are same time or VDDA shoud be faster than the VDD. SPEC No. MODEL No. PAGE LCY-12T09302A 6-3）Input signal characteristics Table6-3-1 Item Frame frequency Clock frequency Vertical Interval COM Frequency LS013B4DN01 10 VDDA=＋5.0V、VDD=＋5.0V、GND=0V、Ta=25℃ Symbol fSCS fSCLK tV fCOM 16.66 0.5 MIN 1 TYP 1 MAX 60 2 1000 30 Unit Hz MHz ms Hz Remark Table 6-3-2 Item SCS Rising time SCS Falling Time SCS High duration SCS Low duration SCS set up time SCS hold time SI frequency SI Rising time SI Folling time SI set up time SI hold time SCLK Rising time SCLK Folling time SCLK High duration SCLK Low duration VDDA=＋5.0V、VDD=＋5.0V、GND=0V、Ta=25℃ Symbol trSCS tfSCS twSCSH twSCSL tsSCS thSCS fSI trSI tfSI tsSI thSI trSCLK tfSCLK twSCLKH twSCLKL fEXTCOMIN trEXTCOMIN tfEXTCOMIN thlEXTCOMIN trDISP tfDISP 1 50 50 MIN 68 12 (1) (3) (1) (120) (125) 200 200 TYP 0.5 450 450 1 MAX 50 50 1 50 50 50 50 60 50 50 Unit ns ns us us us us us MHz ns ns ns ns ns ns ns ns Hz ns ns us ns ns [Remark6-6] [Remark 6-4] [Remark 6-5] Remark EXTCOMIN signal freequency EXTCOMIN signal rising time EXTCOMIN signal folling time EXTCOMIN signalHigh duration DISP Rising time DISP Folling time ( ) is tentative valure. [Remark6-4] Data renew mode. [Remark6-5] Display mode. [Remark6-6] Adjust EXTCOMIN frequency to be lower than the frame frequency. SPEC No. MODEL No. PAGE LCY-12T09302A LS013B4DN01 11 SCS、SI、SCLK Signal SCS 50% 10% 90% twSCSH 90% twSCSL 50% 10% 50% trSCS SI tsSCS 90% 10% 10% 90% 10% 10% thSCS tfSCS trSI tsSI SCLK 10% tfSI thSI 50% 10% twSCLKH twSCLKL 50% 50% 90% 90% 90% trSCLK tfSCLK EXTCOMIN Signal EXTCOMIN 10% 90% 90% 10% 50% twEXTCOMINH 50% twEXTCOMINL 50% trEXTCOMIN tfEXTCOMIN DISP Signal DISP 10% 90% 90% 10% trDISP tfDISP ※SCS,SI,SCLK、DISP: 3V Amplitude EXTCOMIN : 5V amplitude. SPEC No. MODEL No. PAGE LCY-12T09302A 6-4）Power consumption (Average) Table6-4 Item Condition1 Condition2 Symbol MIN TYP 15 30 MAX LS013B4DN01 12 Ta＝25℃ unit uW uW Remark [Remark6-6] [Remark6-6] ＊Condition1 Display mode (No display data update) Common AC Driving with VDD=5V, VDDA=5V, fSCLK=1MHz, fSCS=１Hz, Display pattern: Vertical stripe display ＊Condition 2 Data Renew mode (With display data update: 1Hz) Common AC Driving with VDD=5V, VDDA=5V, fSCLK=1MHz, fSCS=１Hz, Display pattern: Vertical stripe display [Remark6-6] This is the average power in normal condition, not the peak power for COM driving. Allow margin in power supply. Use of capacitor is recommended for VDD+VDDA. (If VDD and VDDA are separate, use of capacitor on each is recommended.) 6-5）Input Signal Timing Chart 6-5-1 Data Renew Mode (1 line) Renews data on one specified line. (M0=”H”, M2=”L”) twSCSH SCS SI tsSI SCLK Mode selection period (3ck+5ckDMY) Gate line address period (7ck+1ckDMY) Data writing period (96ck) Data transfer period (16ck) tsSCS M0 M1 M2 DMYDMYDMYDMYDMY AG0 AG1 AG2 AG3 AG4 AG5 AG6 DMY D1 thSI twSCLKL twSCLKH D2 D3 D4 D93 D94 D95 D96 DUMMY DATA(don't care) thSCS twSCSL ・M0：Mode flag: If M0 is "H". -> Data refresh mode "Pixel data will be updated" . If M0 is "L" -> Display mode "Pixel data is held. ・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output. In addition, if EXTMODE is set as "H", M1 set value doesn't matter. ・M2：All flags are cleared. If M2 is "L" then all flags are cleared. When all clear are needed, refer to "all clear timing chart" ・D1 - D96：Display data: If D* is "L" then Black display can be appeared, if D* is "H" then White display can be appeared ・DUMMY DATA： Dummy data. Don't care but "L" is recommended ※In term of Data transfer period The data which has been stored in 1st latch block is transferred to pixel memory. ※In terms of Data writing period Data has been stored in 1st latch block of Binary driver on Panel. Renews data on one specified line. (M0=”H”, M2=”L”) ※Refer to 6-6) Input Signal and Display for gate line address setting. ※M1: Frame inversion flag is enabled when EXTMODE=”L”. ※When SCS becomes L, M0 and M2 are cleared. ※In renew mode (When M2=”H”) do “All Clear”, and set P1 through P96 as L. SPEC No. MODEL No. PAGE LCY-12T09302A 6-5-2 Data Renew Mode Updates multiple line data. (M0=”H”, M2=”L”) twSCSH SCS tsSCS SI tsSI SCLK Mode selection period (3ck+5ckDMY) Gate line address period (7ck+1ckDMY) GL1 Data transfer period (96ck) M0 M1 M2 DMY DMY DMY DMY DMY AG0 AG1 AG2 AG3 AG4 AG5 AG6 DMY LS013B4DN01 13 D1 D2 D3 D4 D93 D94 D95 D96 DUMMY DATA(don't care) AG0 AG1 AG5 AG6 DMY D1 D2 thSI twSCLKL twSCLKH Data transfer period (8ck(Dummy)+7ck(address)+1ck(Dummy)=16ck) GL2 twSCSH twSCSL thSCS D95 D96 DUMMY DATA(don't care) AG0 AG1 AG4 AG5 AG6 DMY D1 D2 D94 D95 D96 DUMMY DAT A(don't care) GL(n-1)th Line Data transfer period (8ck(Dymmy)+7ck(address)+1ck(Dummy)=16ck) GL(n)th line Data writing period (96ck) Data transfer period (16ck) ・M0：Mode flag: If M0 is "H" then Data refresh mode "Pixel data will be updated, If M0 is "L" then display mode "Pixel data is held" ・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output. In addition, if EXTMODE is set as "H", M1 set value doesn't matter. ・M2：All flags are cleared. If M2 is L then all flags are cleared. When all clear are needed, refer to "all clear timing chart" ・D1 - D96：Display data: If D* is "L" then Black display can be appeared, if D* is "H" then White display can be appeared ・DUMMY DATA： Dummy data. Don't care but "L" is recommended ※In terms of Data writing period Data has been stored in 1st latch block of Binary driver on Panel. ※In term of Data transfer period As an example, the 1st latch block in binary driver which stored the data of 1st gate line"GL1"output the data to GL1 and store the data for 2nd gateline"GL2" at same time. ※Refer to 6-6) Input Signal and Display for gate line address setting. ※Input data continuously. ※M1: Frame inversion flag is enabled when EXTMODE=”L”. ※When SCS becomes L, M0 and M2 are cleared. ※In renew mode (When M2=”H”) do “All Clear”, and set P1 through P96 as L. SPEC No. MODEL No. PAGE LCY-12T09302A 6-5-3 Display mode LS013B4DN01 14 Maintains data in the memory(Maitain the current display)(M0=”L”、M2＝”L”) tV twSCSH SCS tsSCS SI tsSI SCLK Mode selection period (3ck) Data transfer period (More than 13ck) M0 M1 M2 DUMMY DATA(don't care) twSCSL thSCS M0 M1 M2 DUMMY DATA(don't care) thSI ・M0：Mode flag: If M0 is "L" then display mode "Pixel data is held", If M0 is "H" then Data refresh mode "Pixel data will be updated. ・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output. In addition, if EXTMODE is set as "H", M1 set value doesn't matter. ・M2：All flags are cleared. If M2 is L then all flags are cleared. When all clear are needed, refer to "all clear timing chart" ・DUMMY DATA： Dummy data. Don't care but "L" is recommended ※M1: Frame inversion flag is enabled when EXTMODE=”L”. ※When SCS becomes L, M0 and M2 are cleared. SPEC No. MODEL No. PAGE LCY-12T09302A 6-5-4 All Clear mode LS013B4DN01 15 Clear data in the pixel and the memory data and displays white color. (M0=”L”、M2＝”H”) tV twSCSH SCS tsSCS SI tsSI SCLK Mode selection period (3ck) Data transfer period (More than 13ck) M0 M1 M2 DUMMY DATA(don't care) twSCSL thSCS M0 M1 M2 DUMMY DATA(don't care) thSI ・M0：Mode flag: If M0 is "L" then display mode "Pixel data is held", If M0 is "H" then Data refresh mode "Pixel data will be updated. ・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output. In addition, if EXTMODE is set as "H", M1 set value doesn't matter. ・M2：All flags are cleared. If M2 is L then all flags are cleared. When all clear are needed, refer to "all clear timing chart" ・DUMMY DATA： Dummy data. Don't care but "L" is recommended ※M1: Frame inversion flag is enabled when EXTMODE=”L”. ※When SCS becomes L, M0 and M2 are cleared. SPEC No. MODEL No. PAGE LCY-12T09302A 6-5-5 COM Inversion There are two signals, one is COM signal with serial Input(EXTMODE=”L”) and other is external COM signal input (EXTMODE=”H”). EXTMODE="L" LS013B4DN01 16 SCS SI COM fCOM ※2 ※2 M0 M1 M2 ※1 M0 M1 M2 ※1 M0 M1 M2 ※1 ・M1：LC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output. ※1：LC inversion has been changed by M1 flag statement. ※2：The periods of plus polarity and minus polarity should be same length as much as possible. EXTMODE="H" SCS EXTCOMIN COMZ fEXTCOMIN twEXTCOMIN ※1 COM fCOM ※2 ※1 ※1 ※2 ※1：LC inversion polarity has been set by the rising timing of EXTCOMIN in internal circuit block as COMZ signal, and when SCS become falling timing, LC inversion has been activated as COM signal. ※2：The period of EXTCOMIN should be constant. Truth table of COM ＜EXTMODE="L"＞ COM 反転前 反転後 反転前 反転後 ＜EXTMODE="H"＞ COMZ 反転前 反転後 EXTCOMIN L L H H EXTCOMIN COMZ L H COM SCS="L" SCS="H" L Qn-1 H Qn-1 Depend on status of M1 L L L H H L H L H H H L In rising timing of EXTMODE, internal signal "COMZ" is inverted. ※Qn-1： COM has been changed polarity when SCS meet falling edge. (COMZ status has been fixed by signal SCS) SPEC No. MODEL No. PAGE LCY-12T09302A 6-6）Input Signal and Display, Gate address(Line) Setting Data position in display〔H,V〕 LS013B4DN01 17 Up P1,L1 P2,L1 P3,L1 P96, L1 P1,L2 P2,L2 P1,L3 Display side up P1,L96 P96,L96 ライン Line L1 L2 L3 ・ ・ ・ L94 L95 L96 Gate line address setting ゲートラインアドレス設定 AG0 H L H ・ ・ ・ L H L AG1 L H H ・ ・ ・ H H L AG2 L L L ・ ・ ・ H H L AG3 L L L ・ ・ ・ H H L AG4 L L L ・ ・ ・ H H L AG5 L L L ・ ・ ・ L L H AG6 L L L ・ ・ ・ H H H SPEC No. MODEL No. PAGE LCY-12T09302A 7．Optical characteristics Table 7-1 Item Viewing angle CR≧5 Contrast ratio Reflecivity ratio Response time Rise Fall H V Symbol θ21,θ22 θ11 θ12 CR. R τr τd 5 MIN. TYP. TBD TBD TBD 10 50 50 50 MAX. LS013B4DN01 18 Ta=25℃ unit °(degree) °(degree) °(degree) [Remark7-2､3] % ms ms [remark7-3] [Remark 7-3,4] Remark [Remark7-1] Panel Chromaticity White x y 0.313 0.338 [Remark7-3] [Remark7-3] Optical characteristics measurement equipment. Figure 7-2 is for contrast ratio, reflectivity ratio, and panel chromaticity measurement, and figure 7-3 is for response time measurement. Both are to be conducted in a dark or room equipment to a dark room Measurement equipment (CM-2002) Normal line Measurement equipment (LCD-5200) Normal line Light receiver Light source Light receiver Light source -30° Integrating sphere LCD panel Display center Display center LCD panel Fig7-2 Contrast ratio, Reflection ratio, Panel chromaticity of white Fig7-3 response time SPEC No. MODEL No. PAGE LCY-12T09302A [Remark7-1] Defintion of Viewint Angle Normal Δθ22 Δθ11 Δθ12 Δθ21 LS013B4DN01 19 6 o’clock [Remark7-2] Defintion of Contrast Retio Contrast ratio(CR) ＝ Reflection intensity in white display Reflection intensity in black display [Remark7-4] Respons time (Change in reflection ratio) It’s difined by the time change of optical receiver output when signal is input to display white or black White 100% 90% Photo detector output Black White 10% 0% Time τ ｒ τ ｄ SPEC No. MODEL No. PAGE LCY-12T09302A 8．Module outline 1.35 Inch（96×96） Monochromatic zebra connector specifications LS013B4DN01 20 external form drawing Fig8-1 Fig 8-2 SPEC No. MODEL No. PAGE LCY-12T09302A 9. External capacitor LS013B4DN01 21 Fig.9-1 External capacitor recommendation capacity value ＜Recommended capacity value＞ C1：DISP- VSS: rank B C3：VDD- VSS: rank B 0.1uF Ceramic capacitor Ceramic capacitor 1uF Ceramic capacitor C2：VDDA- VSS: rank B 1uF [Remark] The recommedation capacity of an external capacitor is shown. Finally, determine a capacity value after performing evaluation sufficient by your system. (More bigger capacity value is selectable.) SPEC No. MODEL No. PAGE LCY-12T09302A LS013B4DN01 22 10. External Power Supply Circuit 10-1An external power supply circuit is necessary to drive the Pixel Memory LCD with the 3V battery. Table 1-1 shows power supply IC of the recommendation. Table 1-1 Maker SII National Semiconductor Model Number S-8821 LM2750 Note Charge pump type Charge pump type Refer to specifications of each power supply IC for a detailed specification. Set the constant value after it evaluating it sufficiently by an actual application when you use it. 10-2. Electrical specification Table 2-1 Model Number S-8821 LM2750 Vin [V] min 2.8 2.7 max 5.0 5.6 min 4.9 4.8 Vout typ 5.0 5.0 max 5.1 5.2 Iout [A] 0.04 0.04 Refer to specifications of each power supply IC for a detailed specification. Set the constant value after it evaluating it sufficiently by an actual application when you use it. 10-3. Reference circuit The reference circuit is shown below. S-8821 LM2750 SPEC No. MODEL No. PAGE LCY-12T09302A 11．Zebra connector Contact Resistance ：lower than 20Ω 【Recommended zebra connector】 ・ Please select one from these two types. ① Shin-Etsu Polymer: MS-G type LS013B4DN01 23 Recommended size L：27.7±0.25mm W：1.8±0.1mm H：2.3±0.1mm P：0.1mm ② Shin-Etsu Polymer: GB-U type Recommended size L：27.3±0.6mm W：1.7±0.2mm H：2.3±0.2mm P：0.1mm The zebra connector placement position 1．MS-G Specifications（A figure of reference） 2．GB-U Specifications（A figure of reference） Fig 11-1 Fig11-2 SPEC No. MODEL No. PAGE LCY-12T09302A 12. Packaging 12-1）Serial number .( ink-jet print) Show an indication point in a figure of external form dimensions of fig 12-1. LS013B4DN01 24 Model number Print structure LS013B4DN01 9312AD00001FA Display side up Back side up ABC D Serial number specifications A：a single figure of the year B：month(1,2....9,X,Y,Z) C：day D：serial numbeｒ Fig 12-1 Serial number print position SPEC No. MODEL No. PAGE LCY-12T09302A 12-2）Forwarding form ①Piling number of cartons : Max 12 Package quality in a carton: 1,000pcs ②Conditions for storage. ・Temperature： 0～40℃ LS013B4DN01 25 ・Humidity： 60%RH or less (at 40℃) No dew condensation at low temperature and high humidity. ・Atmosphere：Harmful gas, such as acid or alkali which bites electronic components and/or wires, must not be detected. ・Period ・Opening of the package : about 3 months : In order to prevent the LCD module from breakdown by electrostatic charge, please control the room humidity over 50%RH and open the package taking sufficient countermeasures against electrostatic charges, such as earth, etc. 12-3）Packaging fig 12-2 Packege Form SPEC No. MODEL No. PAGE LCY-12T09302A 13. Reliability Test Conditions LS013B4DN01 26 13-1 Reliability test items Table13-1 Test Item 1 2 3 4 5 6 7 High temperature storage test Low temperature storage test High temperature and high humidity operating test High temperature operating test Low temperature operating test Shock test Electro static discharge test Tp=70℃ Tp=-20℃ 240h 240h Ta=80℃ Ta=35℃ Test condition 240h 240h Remark Tp=40℃/95%RH 240h Ta=-30℃(1h)～+80℃(1h) / 5 cycle ±200V、200pF(0Ω) each terminai: 1 time [Remark] Ta = Ambient temperature, Tp = Panel temperature [Check items] In the standard condition, there shall be no practical problems that may affect the display function. 13-2 Panel surface stress spesification Panel surface stress spesification has been defined as a parameter “Force of stress [N]” without no picture failer. Load testing： Minimum 120[N] Test condition : Test stracture Press point Press Jig Press speed Support ：LCD panel with UV protection film ：Center of LCD panel ：φ10mm column ：1mm／minute ：fixed on stage Press time ：5 seconds after achievement of the press strength, then reless it. Technical Document LCD Specification LCD Group NORTH AMERICA Sharp Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-8700 Fax: (1) 360-834-8903 www.sharpsma.com TAIWAN Sharp Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328 CHINA Sharp Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE Sharp Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: 49 (0)180 507 35 07 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE Sharp Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855 KOREA Sharp Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819 JAPAN Sharp Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com HONG KONG Sharp-Roxy (Hong Kong) Ltd. Level 26, Tower 1, Kowloon Commerce Centre, No. 51, Kwai Cheong Road, Kwai Chung, New Territories, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 602-603, 6/F., International Chamber of Commerce Tower, 168 Fuhua Rd. 3, CBD, Futian District, Shenzhen 518048, Guangdong, P.R. China Phone: (86) 755-88313505 Fax: (86) 755-88313515 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in any way, for any incidental or consequential economic or property damage.