PC411L0NIP0F

PC411L0NIP0F Series PC411L0NIP0F Series High Speed 15Mb/s, High CMR Mini-flat Package ∗OPIC Photocoupler ■ Description ■ Agency approvals/Compliance PC411L0NIP0F Series contains a LED optically coupled to an OPIC. It is packaged in a 5 pin mini-flat. Input-output isolation voltage(rms) is 3.75 kV. High speed response (TYP. 15 Mb/s) and CMR is MIN. 15 kV/µs. 1. Recognized by UL1577 (Double protection isolation), file No. E64380 (as model No. PC411L) 2. Approved by VDE, DIN EN60747-5-2 (∗) (as an option), file No. 40009162 (as model No. PC411L) 3. Package resin : UL flammability grade (94V-0) (∗) DIN EN60747-5-2 : successor standard of DIN VDE0884 ■ Features ■ Applications 1. 5 pin Mini-flat package 2. Double transfer mold package (Ideal for Flow Soldering) 3. High noise immunity due to high instantaneous common mode rejection voltage (CMH : MIN. 15 kV/µs, CML : MIN. −15 kV/µs) 4. High speed response (tPHL : TYP. 27 ns, tPLH : TYP. 35 ns) 5. Isolation voltage between input and output (Viso(rms) : 3.75 kV) 6. Lead-free and RoHS directive compliant 1. Programmable controller 2. Inverter ∗ "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and a signal-processing circuit integrated onto a single chip. Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: D2-A04902EN Date Jun. 30. 2005 © SHARP Corporation PC411L0NIP0F Series ■ Internal Connection Diagram 6 5 4 1 Anode 3 5 Cathode GND VO 6 VCC 4 Amp. 1 3 ■ Truth table Input H L LED ON OFF output L H L : Logic (0) H : Logic (1) ■ Outline Dimensions (Unit : mm) 1. Mini-flat Package [ex. PC411L0NIP0F] 2. Mini-flat Package (VDE option) [ex. PC411L0YIP0F] 3.6±0.3 3.6±0.3 1.27 5 1.27±0.25 1.27 1.27 6 4 6 SHARP mark "S" PC4 11L 4.4±0.2 SHARP mark "S" ±0.25 ±0.25 Anode mark 5 4 PC411L Anode mark 4.4±0.2 ±0.25 4 VDE Identification mark Date code 1 3 Date code 1 0.4±0.1 0.4±0.1 Factory identification mark Factory identification mark 5.3±0.3 Epoxy resin 3 5.3±0.3 Epoxy resin 0.1±0.1 2.6±0.2 6˚ 0.5+0.4 −0.2 7.0+0.2 −0.7 Product mass : approx. 0.1g 0.2±0.05 45˚ 0.2±0.05 0.1±0.1 2.6±0.2 45˚ 0.5+0.4 −0.2 6˚ 7.0+0.2 −0.7 Product mass : approx. 0.1g Plating material : SnCu (Cu : TYP. 2%) Sheet No.: D2-A04901EN 2 PC411L0NIP0F Series Date code (2 digit) A.D. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 1st digit Year of production A.D Mark 2002 A 2003 B 2004 C 2005 D 2006 E 2007 F 2008 H 2009 J 2010 K 2011 L 2012 M ·· N · 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D Mark P R S T U V W X A B C ·· · repeats in a 20 year cycle Factory identification mark Factory identification Mark Country of origin no mark Japan Indonesia China * This factory marking is for identification purpose only. Please contact the local SHARP sales representative to see the actual status of the production. Rank mark There is no rank mark indicator. Sheet No.: D2-A04902EN 3 PC411L0NIP0F Series ■ Absolute Maximum Ratings Parameter Forward current Input Reverse voltage Supply voltage Output Output voltage Output current Operating temperature Storage temperature *2 Isolation voltage *3 Soldering temperature *1 Symbol IF VR VCC VO IO Topr Tstg Viso (rms) Tsol Rating 20 5 0 to +6.0 −0.5 to +5.5 2 −40 to +85 −55 to +125 3.75 260 (Ta=25˚C) Unit mA V V V mA ˚C ˚C kV ˚C *1 When ambient temperature goes above 70˚C, the power dissipation goes down at 0.6mA/˚C. (Fig.3) *2 40 to 60 %RH, AC for 1minute *3 For 10s Parameter Forward voltage Reverse current Terminal capacitance High level output voltage Low level output voltage Low level supply current High level supply current "High→Low" input threshold current Isolation resistance Floating capacitance "High→Low" propagation delay time "Low→High" propagation delay time Response time Transfer characteristics Output Input ■ Electro-optical Characteristics*4 *5 Distortion of pulse width Propagation delay skew Rise time Fall time Instantaneous common mode rejection voltage (High level output) Instantaneous common mode rejection voltage (Low level output) (Unless otherwise specified Ta=−40 to 85˚C, VCC=4.5 to 5.5V, TYP. at Ta=25˚C, VCC=5V) Conditions MIN. Symbol Unit TYP. MAX. 1.6 1.95 VF V 1.4 Ta=25˚C, IF=12mA IR − 10 µA Ta=25˚C, VR=5V − 60 150 Ta=25˚C, V=0, f=1MHz pF Ct − 4 5 − V VOH IF=0, IO=−20µA − 1.5 100 mV VOL IF=12mA, IO=20µA ICCL 2.1 − 14.0 mA IF=12mA ICCH IF=0 2.6 − 11.0 mA IFHL VO=2.5V 3.5 − 6.0 mA 1011 − Ta=25˚C, DC500V, 40 to 60%RH Ω 5×1010 RISO − 0.6 1.0 pF Ta=25˚C, V=0V, f=1MHz Cf tPHL 27 20 60 tPLH 35 13 60 IF=12mA, CL=15pF ∆tW 30 8 0 CMOS Logic level ns tr=tf