PQ070XZ01Z

PQ070XZ5MZ/PQ070XZ01Z PQ070XZ5MZ/ PQ070XZ01Z s Features 1. Low voltage operation (Minimum operating voltage:2.35V) 2.5V input → available 1.5 to 1.8V 2. Low dissipation current Dissipation current at no load:MAX.2mA (Conventional model:MAX.10mA) OFF-state dissipation current:MAX.5µA SC-63 Package, Low Voltage Operation Low Power-loss Voltage Regulator s Outline Dimensions 6.6MAX. 5.2 ±0.5 3 (Unit : mm) 2.3±0.5 (0.5) 9.7MAX. 5.5±0.5 070XZ5M Epoxy resin MIN. s Applications 1. Peripheral equipment of personal computers 2. Power supplies for various electronic equipment such as DVD player or STB (0 to 0.25) +0.2 0.5−0.1 2.5 4−(1.27) s Model Line-up Output current (IO) 0.5A 1A Package type Taping Sleeve Taping Sleeve Variable output PQ070XZ5MZP PQ070XZ5MZZ PQ070XZ01ZP PQ070XZ01ZZ (Ta=25°C) Unit V V V A W ˚C ˚C ˚C ˚C ❈( ) : Typical dimensions 1 2 3 4 5 1 2 3 4 5 1 3 Specific IC s Absolute Maximum Ratings Parameter Symbol Rating Input voltage VIN 10 *1 VC 10 Output control voltage *1 VADJ 5 Output adjustment terminal voltage 0.5 Output PQ070XZ5MZ IO 1 current PQ070XZ01Z *2 Power dissipation PD 8 *3 Junction temperature Tj 150 Topr Operating temperature −40 to +85 Storage temperature Tstg −40 to +150 Tsol Soldering temperature 260 (10s) *1 2 5 4 DC input (VIN) ON/OFF control (VC) DC output (VO) Output voltage adjustment (VADJ) GND *1 All are open except GND and applicable terminals *2 PD:With infinite heat sink *3 Overheat protection may operate at the condition Tj=125˚C to 150˚C Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://www.sharp.co.jp/ecg/ (0.9) (0.5) (1.7) PQ070XZ5MZ/PQ070XZ01Z s Electrical Characteristics (Unless otherwise specified, condition shall be VIN=5V, VO=3V(R1=1kΩ), IO=0.3A, VC=2.7V, Ta=25˚C, (PQ070XZ5MZ) ) (Unless otherwise specified, condition shall be VIN=5V, VO=3V(R1=1kΩ), IO=0.5A, VC=2.7V, Ta=25˚C, (PQ070XZ01Z) ) MIN. TYP. MAX. Unit Parameter Symbol Conditions Input voltage range − − V VIN 2.35 10 Output voltage − − V 1.5 7 VO Load regulation Line regulation Ripple Rejection Dropout voltage PQ070XZ5MZ PQ070XZ01Z PQ070XZ5MZ PQ070XZ01Z RegL RegI RR VI-O Vref TCVref VC (ON) IC (ON) VC (OFF) IC (OFF) Iq Iqs IO=5mA to 0.5A IO=5mA to 1A VIN=4 to 8V, IO=5mA Refer to Fig.2 VIN=2.85V, IO=0.3mA VIN=2.85V, IO=0.5mA − Tj=0 to 125˚C, IO=5mA *4 − − 45 − 1.225 − 2 − − − − − 0.2 0.2 60 − ±1.25 ±1.0 − − − − 1 − 2 1 − 0.5 1.275 − − 200 0.8 2 2 5 % % dB V V % V µA V µA mA µA Reference voltage Reference voltage temperature coefficient *4 Output on control voltage Output on control current Output off control voltage Output off control current Quiescent current Output off dissipation current *4 In case of opening control terminal 2 , output voltage turns off − IO=0A IO=0A, VC=0.4V IO=0A VC=0.4V Fig.1 Standard Test Circuit VIN 1 3 R2 VC 2 4 0.33µF A IC 5 A Iq R1 1kΩ V Vref + 47µF RL V VO A IO VO =Vref×(1+R2/R1) .=1.25×(1+R /R ) . 21 = [R1=1kΩ, Vref. .1.25V] Fig.2 Test Circuit for Ripple Rejection + 1 ei ~ VC 0.33µF VIN 2.7V 2 5 R1 1kΩ 4 3 R2 Vref + 47µF RL IO eo V ~ f=120Hz(sine wave) ei(rms)=0.5V VO=3V(R1=1kΩ) VIN=5V IO=0.3A RR=20log(ei(rms)/eo(rms)) PQ070XZ5MZ/PQ070XZ01Z Fig.3 Internal Dissipation vs. Ambient Temperature 10 PD : With infinite heat sink Output voltage VO (V) Fig.4 Overcurrent Protection Characteristics (PQ070XZ01Z) 3 8 Internal dissipation PD (W) 2.5 VIN=4.5V 2 VIN=5V VIN=5.5V VIN=7V 1 VIN=10V 0.5 VO=3V 5 1.5 0 −40 −20 0 0 20 40 60 80 0 0.5 1 Output current IO (A) 1.5 2 Ambient temperature Ta (°C) Note) Oblique line prtion:Overheat protection may operate in this area Fig.5 Overcurrent Protection Characteristics (PQ070XZ5MZ) 3 Fig.6 Reference Voltage vs. Ambient Temperature 1.26 VIN=4V VC=2.7V R1=1kΩ R2=1.4kΩ PQ070XZ5MZ:IO=0.3A 2.5 Reference voltage Vref (V) Output voltage VO (V) VIN=10V 2 VIN=7V 1.255 1.25 PQ070XZ01Z:IO=0.5A 1.245 1.5 VIN=5V 1 VIN=4.5V VIN=5.5V 0.5 VO=3V 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 Output current IO (A) 1.24 1.235 1.23 −50 −25 0 25 50 75 100 125 Ambient temperature Ta (°C) Fig.7 Output Voltage vs. Input Voltage (PQ070XZ5MZ) 3.5 3 Output voltage VO (V) Fig.8 Output Voltage vs. Input Voltage (PQ070XZ01Z) 3.5 3 Output voltage VO (V) 2.5 RL=∞Ω (IO=0A) 2 1.5 1 0.5 0 0 1 2 RL=6Ω (IO=0.5A) RL=10Ω (IO=0.3A) RL=3Ω (IO=1A) 2.5 2 1.5 1 0.5 5 RL=6Ω (IO=0.5A) RL=∞Ω (IO=0.3A) VC=2.7V Ta=Room temp. R1=1kΩ R2=1.4kΩ (VO=3V) CIN=0.33µF CO=47µF 0 1 2 3 4 5 VC=2.7V Ta=Room temp. R1=1kΩ R2=1.4kΩ (VO=3V) CIN=0.33µF CO=47µF 3 4 Input voltage VIN (V) Input voltage VIN (V) PQ070XZ5MZ/PQ070XZ01Z Fig.9 Circuit Operating Current vs. Input Voltage (PQ070XZ5MZ) 20 Circuit operating current IBIAS (mA) VC=2.7V Ta=Room temp. R1=1kΩ R2=1.4kΩ (VO=3V) CIN=0.33µF CO=47µF RL=6Ω (IO=0.5A) RL=∞Ω (IO=0A) RL=10Ω (IO=0.3A) Fig.10 Circuit Operating Current vs. Input Voltage (PQ070XZ01Z) 30 Circuit operating current IBIAS (mA) VC=2.7V Ta=Room temp. R1=1kΩ R2=1.4kΩ (VO=3V) 20 CIN=0.33µF CO=47µF RL=6Ω (IO=0.5A) RL=∞Ω (IO=0A) 10 RL=3Ω (IO=1A) 10 0 0 1 2 3 4 5 Input voltage VIN (V) 0 0 1 2 3 4 5 Input voltage VIN (V) Fig.11 Dropout Voltage vs. Ambient Temperature 0.25 VIN=2.35V VC=2.7V R1=1kΩ R2=1.4kΩ (VO=3V) Fig.12 Quiescent Current vs. Ambient Temperature 1.4 PQ070XZ01Z 1.2 Quiescent current Iq (mA) 0.2 Dropout voltage VI-O (V) PQ070XZ01Z:IO=0.5A 1 PQ070XZ5MZ 0.8 0.6 0.4 0.2 VIN=4V IO=0A VC=2.7V R1=1kΩ R2=1.4kΩ (VO=3V) −25 0 25 50 75 100 125 0.15 0.1 PQ070XZ5MZ:IO=0.3A 0.05 0 −50 −25 0 25 50 75 100 125 0 −50 Ambient temperature Ta (°C) Ambient temperature Ta (°C) Fig.13 Ripple Rejection vs. Input Ripple Frequency 75 70 Ripple rejection RR (dB) 65 60 55 50 45 40 ei(rms)=0.5V VIN=5V VC=2.7V IO=0.3A CO=47µF Ta=Room temp. R1=1kΩ R2=1.4kΩ (VO=3V) 1 PQ070XZ01Z Fig.14 Ripple Rejection vs. Output Current 75 PQ070XZ5MZ 70 Ripple rejection RR (dB) 65 PQ070XZ01Z 60 55 50 45 40 ei(rms)=0.5V f=120Hz VIN=5V VC=2.7V CO=47µF Ta=Room temp. R1=1kΩ R2=1.4kΩ (VO=3V) 0 0.25 0.5 0.75 1 PQ070XZ5MZ 35 0.1 10 100 Input ripple frequency f (kHz) Output current IO (A) PQ070XZ5MZ/PQ070XZ01Z Fig.15 Example of Application DC input 1 3 R2 VIN 2 5 R1 1kΩ 4 CO + Load VO CIN ON/OFF signal High:Output ON    Low or open:Output OFF Fig.16 Power Dissipation vs. Ambient Temperature (Typical Value) 3 Cu area 740mm2 Power dissipation PD (W) 2 Cu area 180mm2 Cu area 100mm2 Cu area 70mm2 1 Cu area 36mm2 Material : Glass-cloth epoxy resin Size : 50×50×1.6mm Cu thickness : 35µm PWB PWB Cu 0 −20 0 20 40 60 80 Ambient temperature Ta (°C) Fig.17 Output Voltage vs. R2 10 9 8 Output voltage VO (V) 7 6 5 4 3 2 1 0 100 1 000 R2 (Ω) 10 000 R1=1kΩ PQ070XZ5MZ/PQ070XZ01Z s Precautions for Use VIN 1 3 VO R2 CIN 2 5 R1 4 CO + Load C-MOS or TTL 1. External connection (1) The connecting wiring of CO, CIN and each terminal, fin portion must be as short as possible. It may oscillate by type, value and wiring condition of capacitor. Confirm the output wareform in actual using condition beforehand. (2) ON/OFF control terminal 2 is compatible with LS-TTL. It enables to be direcrly driven by TTL or C-MOS standard logic (RCA4000 series). (3) If voltage is applied under the conditions that device pin is connected divergently or reversely, the deterioration of characteristics or damage may occur. Never allow improper mounting. 2. Thermal protection design Maximum power dissipation of devices is obtained by the following equation. PD=IO×(VIN−VO)+VIN×Iq When ambient temperature Ta and power dissipation PD (MAX.) during operation are determined, operate element within the safety operation area specified by the derating curve. Insufficient radiation gives an unfavorable influence to the normal operation and reliability of the device. In the external area of the safety operation area shown by the derating curve, the overheat protection circuit may operate to shutdown output. However please avoid keeping such condition for a long time. 3. ESD (Electrostatic Sensitivity Discharge) Be careful not to apply electrostatic discharge to the device since this device employs a bipolar IC and may be damaged by electro static discharge. Followings are some methods against excessive voltage caused by electro static discharge. (1) Human body must be grounded to discharge the electro charge which is charged in the body or cloth. (2) Anything that is in contact with the device such as workbench, inserter, or measuring instrument must be grounded. (3) Use a soldering dip basin with a minimum leak current (isolation resistance 10MΩ or more) from the AC power supply line. Also the soldering dip basin must be grounded. PQ070XZ5MZ/PQ070XZ01Z s Output Voltage Fine Tuning 1. Connecting external resistors R1 and R2 to terminals 3 , 4 , 5 allows the output voltage to be fine tuned from 1.5V to 7V. Refer to the figure below and Fig.17 when connecting external resistors for fine tuning output voltage. 3 R2 − + 5 Vref 4 R1 VO VO =Vref×(1+R2/R1) . 1.25×(1+R /1 000) =. 2 = [R1=1kΩ, Vref. .1.25V] Application Circuits NOTICE qThe circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. qContact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. qObserve the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). qContact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. qIf the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. qThis publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. qContact and consult with a SHARP representative if there are any questions about the contents of this publication. 115