PQ1X451M2ZPH

PQ1Xxx1M2ZPH Series PQ1Xxx1M2ZPH Series Low Output Current, Compact Surface Mount Type Low Power-Loss Voltage Regulators Features 1.Compact surface mount package (2.9×1.6×1.1mm) 2.Low power-loss (Dropout voltage: TYP. 0.11 V/MAX. 0.26V at IO=60mA) Also compatible ceramic capacitors because of suppressing oscillation level 3.High ripple rejection (TYP. 70dB) 4.Built-in ON/OFF control function (Dissipation current at OFF-state: MAX. 1μA) 5.Built-in overcurrent and overheat protection functions *It is available for every 0.1V of output voltage (1.3V to 5.0V) 6.RoHS directive compliant ■ Outline Dimensions (Unit : mm) (1.9) 5 4 X30 1 2 3 5-0.4±0.1 (0.95) Lead finish identification mark (0.95) Applications 1.Cellular phones 2.Cordless phones 3.Personal information tools (PDA) 4.Cameras/Camcoders 5.PCMCIA cards for notebook PCs 1.3MAX (0.3) (2.9TYP. excluding remaining gate) 1.1±0.2 3.3MAX. 1.6±0.2 0.15±0.1 0 to 0.1 15°MAX. 0.2MIN. 2.8±0.3 0.2MIN. ( ) : Typical dimensions Product mass:(0.015g) 1 5 Control circuit 4 1 2 3 4 5 Model Line-up Output Voltage (TYP.) 1.5V 1.8V 2.5V 2.6V 2.7V 2.8V 2.9V Model No. Output Voltage (TYP.) PQ1X151M2ZPH 3.0V PQ1X181M2ZPH 3.3V 3.5V PQ1X251M2ZPH PQ1X261M2ZPH 3.7V PQ1X271M2ZPH 4.0V PQ1X281M2ZPH 4.5V PQ1X291M2ZPH 5.0V Model No. PQ1X301M2ZPH PQ1X331M2ZPH PQ1X351M2ZPH PQ1X371M2ZPH PQ1X401M2ZPH PQ1X451M2ZPH PQ1X501M2ZPH 2 3 DC input (VIN) GND ON/OFF control terminal (VC) Noise reduction (Nr) DC output (VO) Lead finish:Lead-free solder plating (Composition: Sn2Cu) Absolute Maximum Ratings (Ta=25°C) Parameter *1 Input voltage Symbol VIN *1 ON/OFF control terminal voltage VC Output current IO *2 Power dissipation PD *3 Junction temperature Tj Operating temperature Topr Storage temperature Tstg Soldering temperature Tsol Rating 9 9 300 350 150 -30 to +85 -55 to +150 270(10s) Unit V V mA mW °C °C °C °C *1 All are open except GND and applicable terminals. *2 At mounted on PCB *3 Overheat protection may operate at Tj:125°C to 150°C Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: OP06028 PQ1Xxx1M2ZPH Series Electrical Characteristics Parameter Output voltage 4 Input 5 (Unless otherwise specified,VIN=VO(TYP) + 1.0V, IO=30mA,VC=1.8V, Ta=25°C) Symbol VO VIN Iop Conditions MIN. 2.3 180 TYP. MAX. 9 Unit V V mA mA mV mV mV mV mV/°C dB μV V V μA V μA μA voltage Output peak current Recommended output current Load regulation Line regulation Temperature coefficient of output voltage Ripple rejection Output noise voltage RegL1 RegL2 RegL3 RegI TCVO RR VI-O1 VI-O2 VC(ON) IC(ON) VC(OFF) Iq Iqs Io=5 to 60mA Io=5 to 100mA Io=5 to 150mA VIN=VO(TYP)+1V to VO(TYP)+6V(MAX.9.0V) Refer to the following table.1 300 IO=10mA, Tj=-25 to +75°C Refer to Fig.2 IO=60mA IO=150mA 7 7 1.8 10 20 40 3.0 0.05 70 0.11 0.20 150 50 100 160 20 0.26 0.4 Vno(rms) 10Hz