6AG12266RA325XB0

Data sheet 6AG1226-6RA32-5XB0 SIPLUS S7-1200 SM 1226 F-DQ 2x relay -25...+55°C with conformal coating based on 6ES7226-6RA32-0XB0 . F-DQ 2x RLY 5A, PROFIsafe, 70 mm overall width, up to PL E (ISO 13849-1)/ SIL3 (IEC 61508) General information Product type designation SM 1226, F-DQ 2x relay/5 A Supply voltage permissible range, lower limit (DC) 20.4 V permissible range, upper limit (DC) 28.8 V Input current from backplane bus 5 V DC, max. 120 mA Digital outputs ● from load voltage L+, max. 300 mA Power loss Power loss, typ. 10 W Digital outputs Number of digital outputs 2 Short-circuit protection No Output current ● for signal "1" rated value 5A ● for signal "1" permissible range, max. 5 A maximum per circuit and 10 A maximum of all circuits per module Relay outputs ● Number of relay outputs 2; 2 circuits per output Switching capacity of contacts — with inductive load, max. 0.1 Hz, accordance with IEC 60947-5-1, DC-13; 2 Hz, accordance with IEC 60947-5-1, AC-15 — with resistive load, max. 2 Hz Cable length ● shielded, max. 200 m ● unshielded, max. 200 m Interrupts/diagnostics/status information Diagnostics indication LED ● for status of the outputs Yes Standards, approvals, certificates Highest safety class achievable in safety mode ● Performance level according to ISO 13849-1 Category 4, PL e ● SIL acc. to IEC 61508 SIL 3 Ambient conditions Free fall ● Fall height, max. 6AG12266RA325XB0 Page 1/2 0.3 m; five times, in product package 12.21.2020 Subject to change without notice © Copyright Siemens Ambient temperature during operation ● min. -25 °C; = Tmin ● max. 55 °C; = Tmax Ambient temperature during storage/transportation ● min. -40 °C ● max. 70 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 2 000 m ● Ambient air temperature-barometric pressurealtitude Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) Relative humidity ● With condensation, tested in accordance with IEC 60068-2-38, max. 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) Resistance Coolants and lubricants — Resistant to commercially available coolants and lubricants Yes Use in stationary industrial systems — to biologically active substances according to EN 60721-3-3 Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request — to chemically active substances according to EN 60721-3-3 Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * — to mechanically active substances according to EN 60721-3-3 Yes; Class 3S4 incl. sand, dust, * Use on ships/at sea — to biologically active substances according to EN 60721-3-6 Yes; Class 6B2 mold and fungal spores (excluding fauna); Class 6B3 on request — to chemically active substances according to EN 60721-3-6 Yes; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * — to mechanically active substances according to EN 60721-3-6 Yes; Class 6S3 incl. sand, dust; * Usage in industrial process technology — Against chemically active substances acc. to EN 60654-4 Yes; Class 3 (excluding trichlorethylene) — Environmental conditions for process, measuring and control systems acc. to ANSI/ISA71.04 Yes; Level GX group A/B (excluding trichlorethylene; harmful gas concentrations up to the limits of EN 60721-3-3 class 3C4 permissible); level LC3 (salt spray) and level LB3 (oil) Remark — Note regarding classification of environmental conditions acc. to EN 60721, EN 60654-4 and ANSI/ISA-71.04 * The supplied plug covers must remain in place over the unused interfaces during operation! Conformal coating ● Coatings for printed circuit board assemblies acc. to EN 61086 Yes; Class 2 for high reliability ● Protection against fouling acc. to EN 60664-3 Yes; Type 1 protection ● Military testing according to MIL-I-46058C, Amendment 7 Yes; Discoloration of coating possible during service life ● Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies according to IPC-CC-830A Yes; Conformal coating, Class A Mechanics/material Enclosure material (front) ● Plastic Yes Dimensions Width 70 mm Height 100 mm Depth 75 mm Weights Weight, approx. 300 g last modified: 12/18/2020 6AG12266RA325XB0 Page 2/2 12.21.2020 Subject to change without notice © Copyright Siemens