6AG13316SB007AY0

Data sheet 6AG1331-6SB00-7AY0 SIPLUS LOGO! POWER 24V 1.3A SIPLUS LOGO! Power 24V 1,3A for medial stress -40...+70°C start up at -25°C based on 6EP33316SB00-0AY0 . stabilized power supply input: AC 100-240 V output: DC 24 V / 1,3 A Input Input 1-phase AC or DC Rated voltage value Vin rated 100 ... 240 V Voltage range AC 85 ... 264 V input voltage ● at DC 110 ... 300 V Wide-range input Yes Mains buffering at Vin = 187 V Mains buffering at Iout rated, min. 40 ms; at Vin = 187 V Rated line frequency 1 50 Hz Rated line frequency 2 60 Hz Rated line range 47 ... 63 Hz input current ● at rated input voltage 120 V 0.7 A ● at rated input voltage 230 V 0.35 A Switch-on current limiting (+25 °C), max. 25 A I²t, max. 0.8 A²·s Built-in incoming fuse internal Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: from 6 A characteristic B or from 2 A characteristic C Output Output Controlled, isolated DC voltage Rated voltage Vout DC 24 V Total tolerance, static ± 3% Static mains compensation, approx. 0.1 % Static load balancing, approx. 0.1 % Residual ripple peak-peak, max. 200 mV Residual ripple peak-peak, typ. 30 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 300 mV Spikes peak-peak, typ. (bandwidth: 20 MHz) 50 mV Adjustment range 22.2 ... 26.4 V product function output voltage adjustable Yes Output voltage setting via potentiometer 6AG13316SB007AY0 Page 1/2 12.23.2020 Subject to change without notice © Copyright Siemens Status display Green LED for output voltage OK On/off behavior No overshoot of Vout (soft start) Startup delay, max. 0.5 s Voltage rise, typ. 100 ms Rated current value Iout rated 1.3 A Current range 0 ... 1.3 A ● Note +55 ... +70 °C: Derating 2%/K supplied active power typical 31.2 W Parallel switching for enhanced performance Yes Numbers of parallel switchable units for enhanced performance 2 Efficiency Efficiency at Vout rated, Iout rated, approx. 86 % Power loss at Vout rated, Iout rated, approx. 5W power loss [W] during no-load operation maximum 0.3 W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.2 % Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ. 1% Load step setting time 10 to 90%, typ. 1 ms Load step setting time 90 to 10%, typ. 1 ms Protection and monitoring Output overvoltage protection Yes, according to EN 60950-1 Current limitation, typ. 1.7 A property of the output short-circuit proof Yes Short-circuit protection Constant current characteristic enduring short circuit current RMS value ● maximum 1.7 A overcurrent overload capability in normal operation overload capability 150% Iout rated typ. 200 ms Overload/short-circuit indicator - measuring point for output current 50 mV =^ 1.3 A overcurrent overload capability when switching on 150% Iout rated typ. 200 ms Safety Primary/secondary isolation Yes galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 Protection class Class II (without protective conductor) Degree of protection (EN 60529) IP20 Approvals CE mark Yes EMC Emitted interference EN 55022 Class B Supply harmonics limitation not applicable Noise immunity EN 61000-6-2 environmental conditions ambient temperature in horizontal mounting position during operation -40; Startup @ -25 °C ... +70; with natural convection ambient temperature during storage and transport -40 ... +85 installation altitude at height above sea level maximum 6 000 m ambient condition relating to ambient temperature - air pressure - installation altitude In case of operation at altitudes of 2000 - 6000 m above sea level: Output power derating of -7.5 %/1000 m or reduction of the ambient temperature by 5 K/1000 m relative humidity with condensation acc. to IEC 60068-238 maximum 100 %; RH incl. condensation/frost (no commissioning if condensation is present), horizontal installation chemical resistance to commercially available cooling lubricants Yes; incl. diesel and oil droplets in the air resistance to biologically active substances conformity acc. to EN 60721-3-3 Yes; Class 3B2 mold, fungal, sponge spores (except fauna); class 3B3 upon request resistance to chemically active substances conformity acc. to EN 60721-3-3 Yes; Class 3C4 (RH < 75%) incl. salt spray acc. to EN 60068-2-52 (severity level 3) resistance to mechanically active substances conformity Yes; Class 3S4 incl. sand, dust 6AG13316SB007AY0 Page 2/3 12.23.2020 Subject to change without notice © Copyright Siemens acc. to EN 60721-3-3 resistance to biologically active substances conformity acc. to EN 60721-3-6 Yes; Class 6B2 mold, fungal, sponge spores (except fauna) resistance to chemically active substances conformity acc. to EN 60721-3-6 Yes; Class 6C3 (RH < 75%) incl. salt spray acc. to EN 60068-2-52 (severity level 3) resistance to mechanically active substances conformity acc. to EN 60721-3-6 Yes; Class 6S3 incl. sand, dust coating for equipped printed circuit board acc. to EN 61086 Yes; Class 2 for high availability type of coating protection against pollution according to EN 60664-3 Yes; Type 1 protection type of test of the coating acc. to MIL-I-46058C Yes; Discoloration of the coating during service life possible product conformity of the coating Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies acc. to IPC-CC-830A Yes; Conformal Coating, Class A Mechanics Connection technology screw-type terminals Connections ● Supply input L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded ● Output +, -: 2 screw terminals each for 0.5 ... 2.5 mm² ● Auxiliary - width of the enclosure 36 mm height of the enclosure 90 mm depth of the enclosure 53 mm required spacing ● top 20 mm ● bottom 20 mm ● left 0 mm ● right 0 mm Weight, approx. 0.12 kg product feature of the enclosure housing can be lined up Yes Installation Snaps onto DIN rail EN 60715 35x7.5/15, direct mounting in different mounting positions MTBF at 40 °C 3 094 996 h other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 6AG13316SB007AY0 Page 3/3 12.23.2020 Subject to change without notice © Copyright Siemens