6EP13211LD00

Data sheet 6EP1321-1LD00 SITOP PSU100D/1AC/12VDC/3A PSU100D 12 V/3 A Stabilized power supply input: 100-240 V AC output: 12 V DC/3 A Input type of the power supply network 1-phase AC supply voltage at AC ● minimum rated value 100 V ● maximum rated value 240 V ● initial value 85 V ● full-scale value 264 V design of input wide range input Yes operating condition of the mains buffering at Vin = 115/230 V buffering time for rated value of the output current in the event of power failure minimum 15 ms operating condition of the mains buffering at Vin = 115/230 V line frequency ● 1 rated value 50 Hz ● 2 rated value 60 Hz line frequency 47 ... 63 Hz input current ● at rated input voltage 100 V 0.75 A ● at rated input voltage 240 V 0.5 A current limitation of inrush current at 25 °C maximum 60 A I2t value maximum 1.2 A²·s fuse protection type internal ● in the feeder Recommended miniature circuit breaker: from 10 A characteristic C or from 16 A characteristic B Output voltage curve at output Controlled, isolated DC voltage output voltage at DC rated value 12 V output voltage ● at output 1 at DC rated value 12 V relative overall tolerance of the voltage 2% relative control precision of the output voltage ● on slow fluctuation of input voltage 0.5 % ● on slow fluctuation of ohm loading 1% residual ripple ● maximum 100 mV voltage peak ● maximum 100 mV adjustable output voltage 11 ... 14 V product function output voltage adjustable Yes type of output voltage setting via potentiometer 6EP13211LD00 Page 1/3 7/9/2022 Subject to change without notice © Copyright Siemens display version for normal operation Green LED for 12 V OK behavior of the output voltage when switching on Overshoot of Vout < 2 % response delay maximum 2.5 s voltage increase time of the output voltage ● maximum 30 ms output current ● rated value 3A ● rated range 0 ... 3 A; +50 ... +70 °C: Derating 2.5%/K supplied active power typical 36 W product feature ● bridging of equipment number of parallel-switched equipment resources for increasing the power Yes 2 Efficiency efficiency in percent 84 % power loss [W] ● at rated output voltage for rated value of the output current typical 6.5 W Closed-loop control relative control precision of the output voltage with rapid fluctuation of the input voltage by +/- 15% typical 0.5 % relative control precision of the output voltage load step of resistive load 50/100/50 % typical 5% Protection and monitoring design of the overvoltage protection < 17.6 V response value current limitation typical 3.6 A property of the output short-circuit proof Yes design of short-circuit protection Electronic shutdown, automatic restart enduring short circuit current RMS value ● typical display version for overload and short circuit 6A - Safety galvanic isolation between input and output Yes galvanic isolation Safety extra low output voltage Vout according to EN 60950-1 operating resource protection class Class I leakage current ● maximum 3.5 mA ● typical 1 mA protection class IP IP20 Approvals certificate of suitability ● CE marking Yes ● UL approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus (UL 60950-1, CSA C22.2 No. 60950-1), File E151273 ● CSA approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus (UL 60950-1, CSA C22.2 No. 60950-1), File E151273 ● cCSAus, Class 1, Division 2 No ● ATEX No certificate of suitability ● IECEx No ● NEC Class 2 No ● ULhazloc approval No ● FM registration No type of certification CB-certificate Yes certificate of suitability ● EAC approval Yes certificate of suitability shipbuilding approval No shipbuilding approval - Marine classification association ● American Bureau of Shipping Europe Ltd. (ABS) No ● French marine classification society (BV) No 6EP13211LD00 Page 2/3 7/9/2022 Subject to change without notice © Copyright Siemens ● DNV GL No ● Lloyds Register of Shipping (LRS) No ● Nippon Kaiji Kyokai (NK) No EMC standard ● for emitted interference EN 55022 Class B ● for mains harmonics limitation not applicable ● for interference immunity EN 61000-6-2 environmental conditions ambient temperature ● during operation -10 ... +70 °C; with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C Mechanics type of electrical connection screw-type terminals ● at input L, N, PE: 1 screw terminal each for 0.3 ... 1.3 mm² single-core/finely stranded ● at output +, -: 1 screw terminal each for 0.3 ... 1.3 mm² ● for auxiliary contacts - width of the enclosure 97 mm height of the enclosure 98 mm depth of the enclosure 38 mm required spacing ● top 20 mm ● bottom 0 mm ● left 20 mm ● right 20 mm net weight 0.37 kg fastening method Wall mounting other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 6EP13211LD00 Page 3/3 7/9/2022 Subject to change without notice © Copyright Siemens