6EP1332-1LB00

Data sheet 6EP1332-1LB00 SITOP PSU100L/1AC/24VDC/2.5A SITOP PSU100L 24 V/2.5 A Stabilized power supply input: 120/230 V AC, output: DC 24 V/2,5 A input type of the power supply network 1-phase AC supply voltage at AC Set by means of selector switch on the device supply voltage 120 V/230 V input voltage 1 at AC 93 ... 132 V input voltage 2 at AC 187 ... 264 V wide range input No overvoltage overload capability 2.3 × Vin rated, 1.3 ms buffering time for rated value of the output current in the event of power failure minimum 20 ms operating condition of the mains buffering at Vin = 93/187 V line frequency 50/60 Hz line frequency 47 ... 63 Hz input current ● at rated input voltage 120 V 1.1 A ● at rated input voltage 230 V 0.65 A current limitation of inrush current at 25 °C maximum 27 A duration of inrush current limiting at 25 °C ● typical 3 ms I2t value maximum 0.3 A²·s fuse protection type T 2 A/250 V (not accessible) fuse protection type in the feeder Recommended miniature circuit breaker: from 3 A characteristic C output voltage curve at output Controlled, isolated DC voltage output voltage at DC rated value 24 V output voltage ● at output 1 at DC rated value 24 V output voltage adjustable Yes; via potentiometer adjustable output voltage 22.8 ... 26.4 V relative control precision of the output voltage ● on slow fluctuation of input voltage 0.1 % ● on slow fluctuation of ohm loading 0.5 % residual ripple ● maximum 150 mV ● typical 10 mV voltage peak ● maximum 240 mV ● typical 50 mV display version for normal operation Green LED for 24 V OK behavior of the output voltage when switching on Overshoot of Vout approx. 4 % 6EP13321LB00 Page 1/4 5/9/2024 Subject to change without notice © Copyright Siemens response delay maximum 1.5 s voltage increase time of the output voltage ● typical 150 ms output current ● rated value 2.5 A ● rated range 0 ... 2.5 A; +45 ... +60 °C: Derating 2%/K supplied active power typical 60 W bridging of equipment Yes number of parallel-switched equipment resources for increasing the power 2 efficiency efficiency in percent 85 % power loss [W] ● at rated output voltage for rated value of the output current typical 9W closed-loop control relative control precision of the output voltage with rapid fluctuation of the input voltage by +/- 15% typical 0.3 % relative control precision of the output voltage at load step of resistive load 10/90/10 % typical 2% setting time ● load step 10 to 90% typical 0.5 ms ● load step 90 to 10% typical 0.7 ms protection and monitoring design of the overvoltage protection < 33 V property of the output short-circuit proof Yes design of short-circuit protection Constant current characteristic ● typical 2.6 A enduring short circuit current RMS value ● typical 4A safety galvanic isolation between input and output Yes galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 operating resource protection class Class I leakage current ● maximum 3.5 mA ● typical 0.4 mA protection class IP IP20 standard ● for emitted interference EN 55022 Class A ● for mains harmonics limitation not applicable ● for interference immunity EN 61000-6-2 standards, specifications, approvals certificate of suitability ● CE marking Yes ● UL approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259 ● CSA approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259 ● EAC approval Yes ● NEC Class 2 No type of certification ● CB-certificate MTBF at 40 °C Yes 3 153 082 h standards, specifications, approvals hazardous environments certificate of suitability ● IECEx No ● ATEX No ● ULhazloc approval No ● cCSAus, Class 1, Division 2 No ● FM registration No standards, specifications, approvals marine classification shipbuilding approval 6EP13321LB00 Page 2/4 No 5/9/2024 Subject to change without notice © Copyright Siemens Marine classification association ● American Bureau of Shipping Europe Ltd. (ABS) No ● French marine classification society (BV) No ● Det Norske Veritas (DNV) No ● Lloyds Register of Shipping (LRS) No standards, specifications, approvals Environmental Product Declaration Environmental Product Declaration Yes Global Warming Potential [CO2 eq] ● total 289.5 kg ● during manufacturing 7.8 kg ● during operation 281.5 kg ● after end of life 0.21 kg ambient conditions ambient temperature ● during operation 0 ... 60 °C; with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C environmental category according to IEC 60721 Climate class 3K3, 5 ... 95% no condensation connection method type of electrical connection screw terminal ● at input L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely stranded ● at output +, -: 2 screw terminals each for 0.5 ... 2.5 mm² ● for auxiliary contacts - mechanical data width × height × depth of the enclosure 32.5 × 120 installation width × mounting height 32.5 mm required spacing ● top 50 mm ● bottom 50 mm ● left 0 mm ● right 0 mm fastening method Snaps onto DIN rail EN 60715 35x7.5/15 ● standard rail mounting Yes ● S7 rail mounting No ● wall mounting No housing can be lined up Yes net weight 0.3 kg further information internet links internet link ● to web page: selection aid TIA Selection Tool https://siemens.com/tst ● to website: Industrial communication http://www.siemens.com/simatic-net ● to website: CAx-Download-Manager http://www.siemens.com/cax additional information other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) security information security information 6EP13321LB00 Page 3/4 Siemens provides products and solutions with industrial cybersecurity functions that support the secure operation of plants, systems, machines and networks. In order to protect plants, systems, machines and networks against cyber threats, it is necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial cybersecurity concept. Siemens’ products and solutions constitute one element of such a concept. Customers are responsible for preventing unauthorized access to their plants, systems, machines and networks. Such systems, machines and components should only be connected to an enterprise network or the internet if and to the extent such a connection is necessary and only when appropriate security measures (e.g. firewalls and/or network segmentation) are in place. For additional information on industrial cybersecurity measures that may be implemented, please visit www.siemens.com/cybersecurity-industry. Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customer’s exposure to cyber threats. To stay informed about product updates, subscribe to the Siemens Industrial Cybersecurity RSS Feed under https://www.siemens.com/cert. (V4.7) 5/9/2024 Subject to change without notice © Copyright Siemens Classifications Version Classification 14 27-04-07-01 eClass 12 27-04-07-01 eClass 9.1 27-04-07-01 eClass 9 27-04-07-01 eClass 8 27-04-90-02 eClass 7.1 27-04-90-02 eClass 6 27-04-90-02 ETIM 9 EC002540 ETIM 8 EC002540 ETIM 7 EC002540 eClass IDEA 4 4130 UNSPSC 15 39-12-10-04 Approvals Certificates General Product Approval Manufacturer Declaration Environment Declaration of Conformity last modified: 5/7/2024 6EP13321LB00 Page 4/4 5/9/2024 Subject to change without notice © Copyright Siemens