6EP1332-5BA00

Product data sheet 6EP1332-5BA00 SITOP PSU100C 24 V/2.5 A STABILIZED POWER SUPPLY INPUT: AC 120-230 V (DC 110-300 V) OUTPUT: DC 24 V/2.5 A Technical specifications Product SITOP PSU100C Power supply, type 24 V/2.5 A Input Input 1-phase AC or DC Rated voltage value Vin rated 100 … 230 V Voltage range 85 … 264 V Input voltage / at DC 110 … 300 V Wide-range input Yes Overvoltage resistance 2.3 × Vin rated, 1.3 ms Mains buffering at Iout rated, min. 20 ms Mains buffering at Vin = 230 V Rated line frequency 50 / 60 Hz Rated line range 47 ... 63 Hz Input current / at nominal level of the input voltage 100 V / nominal value 1.21 A Input current / at nominal level of the input voltage 230 V 0.67 A Switch-on current limiting (+25 °C), max. 31 A Inrush current A²s 2.4 A²·s Built-in incoming fuse internal 6EP1332-5BA00 Page 1/ 4 03/12/2012 subject to modifications © Copyright Siemens AG 2012 Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: from 16 A, characteristic B or from 10 A, characteristic C Output Output controlled, isolated DC voltage Rated voltage 24 V Total tolerance, static ± 3% Residual ripple peak-peak, max. 200 mV Residual ripple peak-peak, typ. 55 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 300 mV Spikes peak-peak, typ. (bandwidth: 20 MHz) 50 mV Adjustment range 22.2 … 26.4 V Product feature / output voltage adjustable Yes Output voltage setting via potentiometer Status display Green LED for output voltage OK On/off behavior Overshoot of Vout approx. 1 % Startup delay, max. 0.7 s Voltage rise, typ. 100 ms Rated current value Iout rated 2.5 A Current range 0 … 2.5 A • Note 2.5 A up to +50 °C, 0.75 A up to +70 °C delivered active power / typ. 60 W Parallel switching for enhanced performance Yes • Note Numbers of parallel switchable units for enhanced performance Start-up with single nominal load only 2 Efficiency Efficiency at Vout rated, Iout rated, approx. 87 % Power loss at Vout rated, Iout rated, approx. 9W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.1 % Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ. 3% Load step setting time 10 to 90%, typ. 4 ms Load step setting time 90 to 10%, typ. 4 ms Protection and monitoring Output overvoltage protection Yes, according to EN 60950 Current limitation, typ. 3A Characteristic feature of the output / short-circuit protected Yes Short-circuit protection Electronic shutdown, automatic restart Overload/short-circuit indicator - Safety 6EP1332-5BA00 Page 2/ 4 03/12/2012 subject to modifications © Copyright Siemens AG 2012 Primary/secondary isolation Yes Potential separation Safety extra low output voltage Vout according to EN 60950-1 and EN 50178 Protection class Class I stray current / maximum 3.5 mA stray current / typical 0.4 mA CE mark Yes UL/CSA approval Yes UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1) Explosion protection ATEX (EX) II 3G Ex nA IIC T4 FM approval - CB approval Yes Marine approval GL and ABS in process Degree of protection (EN 60529) IP20 EMC Emitted interference EN 55022 Class B Supply harmonics limitation not applicable Noise immunity EN 61000-6-2 Operating data Ambient temperature / in operation -20 … +70 °C • Note with natural convection Ambient temparature / on transport -40 … +85 °C Ambient temparature / in storage -40 … +85 °C Humidity class according to EN 60721 Climate class 3K3, no condensation Mechanics Connection technology screw-type terminals Connections / Supply input L, N, PE: Removable screw terminal, each for 1 x 0.5 ... 2.5 mm² Connections / Output +: 1 screw terminal for 0.5 ... 2.5 mm²; -: 2 screw terminals for 0.5 ... 2.5 mm² Connections / Auxiliary - Width / of the housing 45 mm Height / of the housing 80 mm Depth / of the housing 100 mm Installation width 45 mm Mounting height 180 mm Weight, approx. 0.22 kg Product feature / of the housing / housing for side-by-side mounting Yes Type of mounting / wall mounting No Type of fixing / cap rail mounting Yes 6EP1332-5BA00 Page 3/ 4 03/12/2012 subject to modifications © Copyright Siemens AG 2012 Type of mounting / S7-300 rail mounting No Installation Snaps onto DIN rail EN 60715 35x7.5/15 Electrical accessories Removable spring-type terminal 6EP1971-5BA00 Other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) letzte Änderung: Mar 12, 2012 6EP1332-5BA00 Page 4/ 4 03/12/2012 subject to modifications © Copyright Siemens AG 2012