6EP3330-6SB00-0AY0

Data sheet 6EP3330-6SB00-0AY0 LOGO!Power/1AC/24VDC/0.6A LOGO!POWER 24 V / 0.6 A stabilized power supply input: 100-240 V AC output: 24 V DC/ 0.6 A input type of the power supply network 1-phase AC or DC supply voltage at AC ● minimum rated value 100 V ● maximum rated value 240 V ● initial value 85 V ● full-scale value 264 V input voltage at DC 110 ... 300 V wide range input Yes overvoltage overload capability 300 V AC for 1 s buffering time for rated value of the output current in the event of power failure minimum 40 ms operating condition of the mains buffering at Vin = 187 V line frequency 50/60 Hz line frequency 47 ... 63 Hz input current ● at rated input voltage 120 V 0.3 A ● at rated input voltage 230 V 0.2 A current limitation of inrush current at 25 °C maximum 20 A I2t value maximum 0.8 A²·s fuse protection type internal fuse protection type in the feeder Recommended miniature circuit breaker: from 6 A characteristic B or from 2 A characteristic C output voltage curve at output Controlled, isolated DC voltage output voltage at DC rated value 24 V output voltage ● at output 1 at DC rated value output voltage adjustable 24 V No relative control precision of the output voltage ● on slow fluctuation of input voltage 0.1 % ● on slow fluctuation of ohm loading 0.1 % residual ripple ● maximum 200 mV ● typical 30 mV voltage peak ● maximum 300 mV ● typical 50 mV display version for normal operation Green LED for output voltage OK behavior of the output voltage when switching on No overshoot of Vout (soft start) 6EP33306SB000AY0 Page 1/4 5/18/2024 Subject to change without notice © Copyright Siemens response delay maximum 0.5 s voltage increase time of the output voltage ● typical 100 ms output current ● rated value 0.6 A ● rated range 0 ... 0.6 A; +55 ... +70 °C: Derating 2%/K supplied active power typical 14.4 W bridging of equipment No efficiency efficiency in percent 81 % power loss [W] ● at rated output voltage for rated value of the output current typical 3.4 W ● during no-load operation maximum 0.3 W closed-loop control relative control precision of the output voltage with rapid fluctuation of the input voltage by +/- 15% typical 0.2 % relative control precision of the output voltage at load step of resistive load 10/90/10 % typical 2% setting time ● load step 10 to 90% typical 1 ms ● load step 90 to 10% typical 1 ms protection and monitoring design of the overvoltage protection Yes, according to EN 60950-1 property of the output short-circuit proof Yes design of short-circuit protection Constant current characteristic ● typical 0.8 A overcurrent overload capability ● when switching on 150% Iout rated typ. 200 ms ● in normal operation overload capability 150% Iout rated typ. 200 ms enduring short circuit current RMS value ● maximum measuring point for output current 0.8 A No safety galvanic isolation between input and output Yes galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 operating resource protection class Class II (without protective conductor) protection class IP IP20 standard ● for emitted interference EN 55022 Class B ● for mains harmonics limitation not applicable ● for interference immunity EN 61000-6-2 standards, specifications, approvals certificate of suitability ● CE marking Yes ● UL approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURusRecognized (UL 60950, CSA C22.2 No. 60950), File E151273, NEC class 2 (acc. to UL 1310) ● CSA approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURusRecognized (UL 60950, CSA C22.2 No. 60950), File E151273, NEC class 2 (acc. to UL 1310) ● EAC approval Yes ● NEC Class 2 Yes; according to UL1310, File E151273 ● SEMI F47 Yes type of certification ● CB-certificate MTBF at 40 °C Yes 4 415 040 h standards, specifications, approvals hazardous environments certificate of suitability ● IECEx No ● ATEX No ● ULhazloc approval No 6EP33306SB000AY0 Page 2/4 5/18/2024 Subject to change without notice © Copyright Siemens ● cCSAus, Class 1, Division 2 No ● FM registration No standards, specifications, approvals marine classification shipbuilding approval Yes Marine classification association ● American Bureau of Shipping Europe Ltd. (ABS) Yes ● French marine classification society (BV) Yes ● Det Norske Veritas (DNV) Yes ● Lloyds Register of Shipping (LRS) Yes standards, specifications, approvals Environmental Product Declaration Environmental Product Declaration Yes Global Warming Potential [CO2 eq] ● total 107.9 kg ● during manufacturing 1.4 kg ● during operation 106.5 kg ● after end of life 0.04 kg ambient conditions ambient temperature ● during operation -25 ... +70 °C; with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C environmental category according to IEC 60721 Climate class 3K3, 5 ... 95% no condensation connection method type of electrical connection screw terminal ● at input L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded ● at output +, -: 1 screw terminal each for 0.5 ... 2.5 mm² ● for auxiliary contacts - mechanical data width × height × depth of the enclosure 18 × 53 installation width × mounting height 18 mm required spacing ● top 20 mm ● bottom 20 mm ● left 0 mm ● right 0 mm fastening method Snaps onto DIN rail EN 60715 35x7.5/15, direct mounting in different mounting positions ● standard rail mounting Yes ● S7 rail mounting No ● wall mounting Yes housing can be lined up Yes net weight 0.07 kg further information internet links internet link ● to website: Industry Mall https://mall.industry.siemens.com additional information other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) security information security information 6EP33306SB000AY0 Page 3/4 Siemens provides products and solutions with industrial cybersecurity functions that support the secure operation of plants, systems, machines and networks. In order to protect plants, systems, machines and networks against cyber threats, it is necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial cybersecurity concept. Siemens’ products and solutions constitute one element of such a concept. Customers are responsible for preventing unauthorized access to their plants, systems, machines and networks. Such systems, machines and components should only be connected to an enterprise network or the internet if and to the extent such a connection is necessary and only when appropriate security measures (e.g. firewalls and/or network segmentation) are in place. For additional information on industrial cybersecurity measures that may be implemented, please visit www.siemens.com/cybersecurity-industry. Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase 5/18/2024 Subject to change without notice © Copyright Siemens customer’s exposure to cyber threats. To stay informed about product updates, subscribe to the Siemens Industrial Cybersecurity RSS Feed under https://www.siemens.com/cert. (V4.7) Classifications Version Classification eClass 14 27-04-07-01 eClass 12 27-04-07-01 eClass 9.1 27-04-07-01 eClass 9 27-04-07-01 eClass 8 27-04-90-02 eClass 7.1 27-04-90-02 eClass 6 27-04-90-02 ETIM 9 EC002540 ETIM 8 EC002540 ETIM 7 EC002540 IDEA 4 4130 UNSPSC 15 39-12-10-04 Approvals Certificates General Product Approval Manufacturer Declaration General Product Approval For use in hazardous locations Marine / Shipping FM Marine / Shipping last modified: 6EP33306SB000AY0 Page 4/4 Declaration of Conformity CCC-Ex Environment 5/18/2024 5/18/2024 Subject to change without notice © Copyright Siemens