6EP3332-7SB00-0AX0

Data sheet 6EP3332-7SB00-0AX0 SITOP PSU6200/1AC/24VDC/2.5A SITOP PSU6200 24 V/2.5 A Stabilized power supply Input: 120 - 230 V AC, (120 240 V DC) Output: 24 V DC/2.5 A input type of the power supply network 1-phase AC or DC supply voltage at AC ● minimum rated value 120 V ● maximum rated value 240 V ● initial value 85 V ● full-scale value 264 V supply voltage at DC 120 ... 240 V input voltage at DC 110 ... 275 V wide range input Yes overvoltage overload capability 300 V AC for 30 s buffering time for rated value of the output current in the event of power failure minimum 150 ms operating condition of the mains buffering at Vin = 240 V line frequency 50/60 Hz line frequency 47 ... 63 Hz input current ● at rated input voltage 120 V 1.1 A ● at rated input voltage 240 V 0.6 A current limitation of inrush current at 25 °C maximum 32 A fuse protection type 3.15 A fuse protection type in the feeder Circuit breaker from 4 A characteristic C/6 A characteristic B to 16 A characteristic C or circuit breaker 3RV2011-1EA10 (setting 4 A) or 3RV27111ED10 (UL 489) output voltage curve at output Controlled, isolated DC voltage number of outputs 1 output voltage at DC rated value 24 V output voltage ● at output 1 at DC rated value 24 V output voltage adjustable Yes; via potentiometer adjustable output voltage 22.2 ... 26.4 V; max. 60 W relative control precision of the output voltage ● on slow fluctuation of input voltage 0.1 % ● on slow fluctuation of ohm loading 0.1 % residual ripple ● maximum 30 mV ● typical 20 mV voltage peak ● maximum 30 mV ● typical 20 mV 6EP33327SB000AX0 Page 1/4 5/9/2024 Subject to change without notice © Copyright Siemens display version for normal operation Green LED for 24 V OK behavior of the output voltage when switching on Overshoot of Vout approx. 3 % response delay maximum 1s voltage increase time of the output voltage ● typical 100 ms output current ● rated value 2.5 A ● rated range 0 ... 2.5 A; +60 ... +70 °C: Derating 2.5%/K supplied active power typical 60 W short-term overload current ● on short-circuiting during the start-up typical 2.5 A ● at short-circuit during operation typical 2.5 A bridging of equipment No efficiency efficiency in percent 89 % power loss [W] ● at rated output voltage for rated value of the output current typical 7W ● during no-load operation maximum 0.8 W closed-loop control relative control precision of the output voltage at load step of resistive load 10/90/10 % typical 3% setting time ● load step 10 to 90% typical 1 ms ● load step 90 to 10% typical 1 ms ● maximum 2 ms protection and monitoring design of the overvoltage protection < 32 V property of the output short-circuit proof Yes design of short-circuit protection Shutdown and periodic restart attempts ● typical 3.1 A safety galvanic isolation between input and output Yes galvanic isolation Safety extra low output voltage Vout according to EN 60950-1 operating resource protection class Class I leakage current ● maximum protection class IP 3.5 mA IP20 standard ● for emitted interference EN 55022 Class B ● for mains harmonics limitation EN 61000-3-2 ● for interference immunity EN 61000-6-2 standards, specifications, approvals certificate of suitability ● CE marking Yes ● UL approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1) ● CSA approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1) ● EAC approval Yes ● Regulatory Compliance Mark (RCM) Yes ● NEC Class 2 Yes; according to UL1310, File E151273 ● SEMI F47 Yes type of certification ● BIS Yes; R-41183539 ● CB-certificate Yes standards, specifications, approvals hazardous environments certificate of suitability ● IECEx No ● ATEX No ● ULhazloc approval No 6EP33327SB000AX0 Page 2/4 5/9/2024 Subject to change without notice © Copyright Siemens ● cCSAus, Class 1, Division 2 No ● FM registration No standards, specifications, approvals marine classification shipbuilding approval Yes Marine classification association ● American Bureau of Shipping Europe Ltd. (ABS) Yes ● French marine classification society (BV) No ● Det Norske Veritas (DNV) No; in preparation ● Lloyds Register of Shipping (LRS) No standards, specifications, approvals Environmental Product Declaration Environmental Product Declaration Yes Global Warming Potential [CO2 eq] ● total 225.6 kg ● during manufacturing 6.5 kg ● during operation 218.9 kg ● after end of life 0.18 kg ambient conditions ambient temperature ● during operation -25 ... +70 °C; with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C environmental category according to IEC 60721 Climate class 3K3, 5 ... 95% no condensation connection method type of electrical connection push-in terminals ● at input L1/+, L2/N/-, PE: push-in for 0.5 ... 2.5 mm² single-core/finely stranded ● at output +1, -1, -2: push-in for 0.5 ... 2.5 mm² ● for auxiliary contacts - mechanical data width × height × depth of the enclosure 40 × 88 installation width × mounting height 40 mm required spacing ● top 50 mm ● bottom 50 mm ● left 0 mm ● right 0 mm fastening method Snaps onto DIN rail EN 60715 35x7.5/15 ● standard rail mounting Yes ● S7 rail mounting No ● wall mounting No housing can be lined up Yes net weight 0.25 kg accessories electrical accessories Buffer module, redundancy module mechanical accessories Identification labels SIMATIC ET 200SP 6ES7193-6LF30-0AW0 further information internet links internet link ● to web page: selection aid TIA Selection Tool https://siemens.com/tst ● to website: Industrial communication http://www.siemens.com/simatic-net ● to website: CAx-Download-Manager http://www.siemens.com/cax additional information other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) security information security information 6EP33327SB000AX0 Page 3/4 Siemens provides products and solutions with industrial cybersecurity functions that support the secure operation of plants, systems, machines and networks. In order to protect plants, systems, machines and networks against cyber threats, it is necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial cybersecurity concept. Siemens’ products and solutions constitute one element of such a concept. Customers are responsible for preventing unauthorized access to their plants, systems, machines and networks. Such systems, machines and components should only be connected to an enterprise network or the internet if and to the extent such a connection is necessary and only when appropriate security measures (e.g. firewalls and/or 5/9/2024 Subject to change without notice © Copyright Siemens network segmentation) are in place. For additional information on industrial cybersecurity measures that may be implemented, please visit www.siemens.com/cybersecurity-industry. Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customer’s exposure to cyber threats. To stay informed about product updates, subscribe to the Siemens Industrial Cybersecurity RSS Feed under https://www.siemens.com/cert. (V4.7) Classifications Version Classification eClass 14 27-04-07-01 eClass 12 27-04-07-01 eClass 9.1 27-04-07-01 eClass 9 27-04-07-01 eClass 8 27-04-90-02 eClass 7.1 27-04-90-02 eClass 6 27-04-90-02 ETIM 9 EC002540 ETIM 8 EC002540 ETIM 7 EC002540 IDEA 4 4130 UNSPSC 15 39-12-10-04 Approvals Certificates General Product Approval Manufacturer Declaration General Product Approval Declaration of Conformity Marine / Shipping Environment BIS CRS last modified: 6EP33327SB000AX0 Page 4/4 5/7/2024 5/9/2024 Subject to change without notice © Copyright Siemens