6EP33430SA000AY0

Data sheet 6EP3343-0SA00-0AY0 SITOP PSU3600 FLEXI/1AC/3-52VDC/10A/120W SITOP PSU3600 flexi Stabilized power supply Input: 120-230 V AC Output: 3-52 V DC/10 A, 120 W Input Input 1-phase AC or DC Rated voltage value Vin rated 120 ... 230 V Voltage range AC 85 ... 264 V ● Note Derating at < 110 V AC/DC: output power max. 100 W supply voltage ● at DC 110 ... 220 V input voltage ● at DC 88 ... 250 V Wide-range input Yes Mains buffering With Pa = 120 W and Ue = 230 V AC Mains buffering at Iout rated, min. 80 ms; With Pa = 120 W and Ue = 230 V AC Rated line frequency 1 50 Hz Rated line frequency 2 60 Hz Rated line range 47 ... 63 Hz input current ● at rated input voltage 120 V 2.6 A ● at rated input voltage 230 V 1.3 A ● at rated input voltage 110 V 1.3 A ● at rated input voltage 220 V 0.7 A Switch-on current limiting (+25 °C), max. 35 A I²t, max. 1 A²·s Built-in incoming fuse T 3.15 A (not accessible) Protection in the mains power input (IEC 898) Recommended miniature circuit breaker: 6-10 A characteristic C Output Output Controlled, isolated DC voltage Rated voltage Vout DC 24 V ● Output voltage 3-52 V DC Total tolerance, static ± 1% Static mains compensation, approx. 0.1 % Static load balancing, approx. 1% Sense line connection max. voltage control per line 0.5 V Residual ripple peak-peak, max. 50 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 100 mV 6EP33430SA000AY0 Page 1/2 12.17.2020 Subject to change without notice © Copyright Siemens Adjustment range 0 ... 52 V product function output voltage adjustable Yes Output voltage setting via potentiometer (setting range 3 to 52 V) or analog control voltage signal 0 to 2.5 V (setting range 0 to 52 V) Status display Two-color LED: green for 24 V o.k., red for overload Signaling DC OK via relay contact, current monitor signal (0 to 2.5 V correspond to 0 to 10 A) On/off behavior No overshoot of Vout (soft start) Startup delay, max. 0.5 s Voltage rise, typ. 20 ms Rated current value Iout rated 10 A Current range 0 ... 10 A ● Note supplied active power typical Output power max. 120 W 120 W constant overload current ● on short-circuiting during the start-up typical 12 A ● at short-circuit during operation typical 12 A Parallel switching for enhanced performance Yes Numbers of parallel switchable units for enhanced performance 2 Efficiency Efficiency at Vout rated, Iout rated, approx. 88 % Power loss at Vout rated, Iout rated, approx. 16 W power loss [W] during no-load operation maximum 3W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.3 % Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 5% setting time maximum 0.2 ms Protection and monitoring Output overvoltage protection ≤ 60 V according to EN 60950-1 Current limitation 2 ... 10 A Current limitation Can be set with potentiometer or analog control voltage signal 0.5 ... 2.5 V property of the output short-circuit proof Yes Short-circuit protection Electronic current limiting (2 ... 10 A) in the range 3 ... 12 V or power limiting (120 W) in the range 12 ... 52 V enduring short circuit current RMS value ● maximum 12 A Safety Primary/secondary isolation Yes galvanic isolation Safety extra low output voltage Vout according to EN 60950-1 Protection class Class I leakage current ● maximum Degree of protection (EN 60529) 3.5 mA IP20 Approvals CE mark Yes UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259 Explosion protection - certificate of suitability NEC Class 2 No FM approval - CB approval Yes Marine approval - EMC Emitted interference EN 55022 Class B Supply harmonics limitation EN 61000-3-2 Noise immunity EN 61000-6-2 environmental conditions ambient temperature 6EP33430SA000AY0 Page 2/3 12.17.2020 Subject to change without notice © Copyright Siemens ● during operation — Note -25 ... +70 °C Derating > 60°C: 2%/°K ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C Humidity class according to EN 60721 Climate class 3K3, 5 … 95% no condensation Mechanics Connection technology screw-type terminals Connections ● Supply input L1, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely stranded ● Output +, -: 2 screw terminals each for 0.5 ... 2.5 mm² single-core/finely stranded ● Auxiliary Alarm signals, control inputs: screw-type terminals for 0.14 ... 1.5 mm² single-core/finely stranded width of the enclosure 42 mm height of the enclosure 125 mm depth of the enclosure 135 mm required spacing ● top 50 mm ● bottom 50 mm ● left 0 mm ● right 0 mm Weight, approx. 0.55 kg product feature of the enclosure housing can be lined up Yes Installation Snaps onto DIN rail EN 60715 35x7.5/15 MTBF at 40 °C 1 200 000 h other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 6EP33430SA000AY0 Page 3/3 12.17.2020 Subject to change without notice © Copyright Siemens