6EP34368MB002CY0

Data sheet 6EP3436-8MB00-2CY0 SITOP PSU8600/3AC/24VDC/20A/4X5A PN SITOP PSU8600 3AC 20A/4x5A PN Stabilized power supply Input: 400-500 V 3 AC output: 24 V DC/20 A/4x 5 A with PN/IE connection Integrated web server OPC UA server integrated Input Input 3-phase AC Rated voltage value Vin rated 400 ... 500 V Voltage range AC 320 ... 575 V ● Note Derating 320 … 360 and 530 … 575 V Wide-range input Yes Mains buffering at Vin = 400 V; Prioritized supply Output 1 at power failure can be selected via DIP switch Mains buffering at Iout rated, min. 15 ms; at Vin = 400 V; Prioritized supply Output 1 at power failure can be selected via DIP switch Rated line frequency 1 50 Hz Rated line frequency 2 60 Hz Rated line range 47 ... 63 Hz input current ● at rated input voltage 400 V 1.4 A ● at rated input voltage 500 V 1.1 A Switch-on current limiting (+25 °C), max. 14 A I²t, max. 1.2 A²·s Built-in incoming fuse none Protection in the mains power input (IEC 898) Required: 3-pole connected miniature circuit breaker 6 ... 16 A characteristic C or circuit breaker 3RV2011-1DA10 (setting 3 A) or 3RV2711-1DD10 (UL 489) Output Output Controlled, isolated DC voltage number of outputs 4 Rated voltage Vout DC 24 V ● output voltage at output 1 at DC rated value 24 V ● output voltage at output 2 at DC rated value 24 V ● output voltage at output 3 at DC rated value 24 V ● output voltage at output 4 at DC rated value 24 V Total tolerance, static ± 3% Static mains compensation, approx. 0.2 % Static load balancing, approx. 0.1 % 6EP34368MB002CY0 Page 1/2 1.14.2021 Subject to change without notice © Copyright Siemens Residual ripple peak-peak, max. 100 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 200 mV Adjustment range 4 ... 28 V product function output voltage adjustable Yes Output voltage setting via potentiometer or IE/PN interface; Derating > 24 V: 4%/V; max. 120 W per output, max. 480 W overall system Status display 3-color LED for operating state device; LED for operating mode manual/remote; 4 LEDs for communication PROFINET; 3-color LED per output for operating state output; LED green for parallel operation Output 1 and 2 / 3 and 4 Signaling Relay contact (changeover contact, contact current capacity DC 60 V/0.3 A) for "Operating state OK" On/off behavior No overshoot of Vout (soft start) Startup delay, max. 1 s; Without on-delay of the outputs connection of outputs operating Simultaneous connecting-in of all outputs after device booting or delay time of 25 ms, 100 ms or "load-optimized" for sequential cutting-in of the outputs via DIP switches can be set voltage increase time of the output voltage maximum 500 ms Rated current value Iout rated 20 A output current ● per output 5A ● at output 1 rated value 5A ● at output 2 rated value 5A ● at output 3 rated value 5A ● at output 4 rated value 5A Current range ● Note 0 ... 20 A +50 ... +60 °C: Derating 2.5%/K; no derating in connection with expansion module CNX8600 and total load of the outputs at the basic device max. 240 W supplied active power typical 480 W product feature parallel switching of outputs Yes; Parallel circuit Output 1 with 2 or Output 3 with 4 can be selected via DIP switch Parallel switching for enhanced performance No Efficiency Efficiency at Vout rated, Iout rated, approx. 93 % Power loss at Vout rated, Iout rated, approx. 34 W power loss [W] during no-load operation maximum 12 W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.1 % Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 0.4 % setting time maximum 10 ms Protection and monitoring Output overvoltage protection < 35 V property of the output short-circuit proof Yes Short-circuit protection electronic overload cut-off; optionally constant current operation can be selected for Output 4 via DIP switches adjustable response value current of current-dependent overload trip 0.5 ... 5 A type of threshold value setting via potentiometer or IE/PN interface characteristics of electronic overload switch-off Ia >1.0… 15 V) overcurrent overload capability in normal operation Total system overloadable 150% Ia rated to 5 s/min Overload/short-circuit indicator 3-color LED for operating state device; 3-color LED per output for operating state output Interface Specification interface Ethernet/PROFINET Safety 6EP34368MB002CY0 Page 2/3 1.14.2021 Subject to change without notice © Copyright Siemens Primary/secondary isolation Yes galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 Protection class Class I leakage current ● maximum Degree of protection (EN 60529) 3.5 mA IP20 Approvals CE mark Yes UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1) Explosion protection IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc; cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01) Class I, Div. 2, Group ABCD, T4 certificate of suitability NEC Class 2 No FM approval - CB approval Yes Marine approval ABS, DNV GL EMC Emitted interference EN 55022 Class B Supply harmonics limitation EN 61000-3-2 Noise immunity EN 61000-6-2 environmental conditions ambient temperature ● during operation — Note -25 ... +60 °C with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C Humidity class according to EN 60721 Climate class 3K3, 5 … 95% no condensation Mechanics Connection technology Plug-in terminals with screwed connection Connections ● Supply input L1, L2, L3, PE: Plug-in terminal with 1 screwed connection each for 0.2 ... 4 mm² single-wire / fine stranded ● Output 1, 2, 3, 4: Two plug-in terminals (1, 2 and 3, 4) with 2 screwed connections each for 0.2 ... 2.5 mm²; 0 V: Plug-in terminal with 3 screwed connections for 0.2 ... 4 mm² ● Auxiliary RST (Reset): Plug-in terminal (together with alarm signal) with 1 screwed connection for 0.2 ... 1.5 mm² ● signaling contact 11, 12, 14 (alarm signal): Plug-in terminal (together with Reset) with 1 screwed connection each for 0.2 ... 1.5 mm² product function ● removable terminal at input Yes ● removable terminal at output Yes design of the interface for communication PROFINET/Ethernet: two RJ45 sockets (2-port switch) suitability for interaction modular system Yes width of the enclosure 100 mm height of the enclosure 125 mm depth of the enclosure 150 mm required spacing ● top 50 mm ● bottom 50 mm ● left 0 mm ● right 0 mm Weight, approx. 2 kg product feature of the enclosure housing can be lined up Yes Installation Snaps onto DIN rail EN 60715 35x15 electrical accessories Expansion modules CNX8600, buffer modules BUF8600, module UPS8600 mechanical accessories Device identification label 20 mm × 7 mm, TI-grey 3RT2900-1SB20 MTBF at 40 °C 243 178 h 6EP34368MB002CY0 Page 3/4 1.14.2021 Subject to change without notice © Copyright Siemens other information 6EP34368MB002CY0 Page 4/4 Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 1.14.2021 Subject to change without notice © Copyright Siemens