6EP44368XB000DY0

Data sheet 6EP4436-8XB00-0DY0 SITOP CNX8600/8X2.5A SITOP CNX8600 8x2.5 A Extension module for PSU8600 Output: 24 V DC / 8x 2.5 A Outputs according to NEC Class 2 Output Output Controlled, isolated DC voltage number of outputs 8 Rated voltage Vout DC 24 V ● output voltage at output 1 at DC rated value 24 V ● output voltage at output 2 at DC rated value 24 V ● output voltage at output 3 at DC rated value 24 V ● output voltage at output 4 at DC rated value 24 V ● output voltage at output 5 at DC rated value 24 V ● output voltage at output 6 at DC rated value 24 V ● output voltage at output 7 at DC rated value 24 V ● output voltage at output 8 at DC rated value 24 V Total tolerance, static ± 3% Static mains compensation, approx. 0.2 % Static load balancing, approx. 0.1 % Residual ripple peak-peak, max. 100 mV Spikes peak-peak, max. (bandwidth: 20 MHz) 200 mV Adjustment range 4 ... 28 V product function output voltage adjustable Yes Output voltage setting via potentiometer or IE/PN interface; Derating > 24 V: 4%/V; max. 60 W per output Status display 3-color LED for operating state module; 3-color LED per output for operating state output Signaling Relay contact (changeover contact, contact current capacity DC 60 V/0.3 A) for "Operating state OK" at power supply unit PSU8600 On/off behavior No overshoot of Vout (soft start) Startup delay, max. 1.5 s; Without on-delay of the outputs connection of outputs operating Simultaneous connecting-in of all outputs after device booting or delay time of 25 ms, 100 ms or "load-optimized" for sequential cutting-in of the outputs via DIP switches at power supply unit PSU8600 can be set voltage increase time of the output voltage maximum 500 ms Rated current value Iout rated 20 A output current ● per output 2.5 A ● at output 1 rated value 2.5 A 6EP44368XB000DY0 Page 1/2 12.19.2020 Subject to change without notice © Copyright Siemens ● at output 2 rated value 2.5 A ● at output 3 rated value 2.5 A ● at output 4 rated value 2.5 A ● at output 5 rated value 2.5 A ● at output 6 rated value 2.5 A ● at output 7 rated value 2.5 A ● at output 8 rated value 2.5 A Current range ● Note 0 ... 20 A Outputs meet requirements to NEC Class 2; an increase of the maximum output power of the SITOP PSU8600 overall system is not possible over the SITOP CNX8600 expansion module supplied active power typical 480 W product feature parallel switching of outputs No Parallel switching for enhanced performance No Efficiency Efficiency at Vout rated, Iout rated, approx. 97 % Power loss at Vout rated, Iout rated, approx. 15 W Closed-loop control Dynamic mains compensation (Vin rated ±15 %), max. 0.1 % Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ. 0.4 % setting time maximum 10 ms Protection and monitoring Output overvoltage protection < 35 V property of the output short-circuit proof Yes Short-circuit protection electronic overload cut-off adjustable response value current of current-dependent overload trip 0.5 ... 2.5 A type of threshold value setting via potentiometer or IE/PN interface characteristics of electronic overload switch-off Ia >1.0… 15 V) at power supply unit PSU8600 Overload/short-circuit indicator 3-color LED for operating state module; 3-color LED per output for operating state output Interface Specification interface Ethernet/PROFINET via power supply unit PSU8600 Safety Primary/secondary isolation Yes galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 Protection class Class III Degree of protection (EN 60529) IP20 Approvals CE mark Yes UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1), NEC class 2 Explosion protection IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc; cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01) Class I, Div. 2, Group ABCD, T4 certificate of suitability NEC Class 2 Yes FM approval - CB approval Yes Regulatory Compliance Mark (RCM) Yes Marine approval ABS, DNV GL EMC Emitted interference EN 55022 Class B Noise immunity EN 61000-6-2 environmental conditions ambient temperature 6EP44368XB000DY0 Page 2/3 12.19.2020 Subject to change without notice © Copyright Siemens ● during operation — Note -25 ... +60 °C with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C Humidity class according to EN 60721 Climate class 3K3, 5 … 95% no condensation Mechanics Connection technology Plug-in terminals with screwed connection Connections ● Output 1, 2, 3, 4, 5, 6, 7, 8: Two plug-in terminals (1…4 and 5…8) with 1 screwed connection each for 0.2 ... 2.5 mm²; Ground: Plug-in terminal with 3 screwed connections for 0.2 ... 2.5 mm² product function ● removable terminal at output Yes suitability for interaction modular system Yes type of connection to system components Via integrated connector width of the enclosure 100 mm height of the enclosure 125 mm depth of the enclosure 150 mm required spacing ● top 50 mm ● bottom 50 mm ● left 0 mm ● right 0 mm Weight, approx. 1.29 kg product feature of the enclosure housing can be lined up Yes Installation Snaps onto DIN rail EN 60715 35x15 mechanical accessories Device identification label 20 mm × 7 mm, TI-grey 3RT2900-1SB20 MTBF at 40 °C 327 369 h other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 6EP44368XB000DY0 Page 3/3 12.19.2020 Subject to change without notice © Copyright Siemens