6ES71316BF012AA0

Data sheet 6ES7131-6BF01-2AA0 SIMATIC ET 200SP, Digital input module, DI 8x 24V DC Basic, type 2 (IEC 61131), sink input, (PNP, P-reading), Packing unit: 10 pieces, fits to BUtype A0, Colour Code CC01, input delay time 0,05..20ms, module diagnostics for: supply voltage General information Product type designation DI 8x24VDC BA HW functional status FS03 Firmware version V0.0 ● FW update possible No usable BaseUnits BU type A0 Color code for module-specific color identification plate CC01 Product function ● I&M data Yes; I&M0 to I&M3 ● Isochronous mode No Engineering with ● STEP 7 TIA Portal configurable/integrated from version V14 ● STEP 7 configurable/integrated from version V5.5 SP3 / - ● PROFIBUS from GSD version/GSD revision One GSD file each, Revision 3 and 5 and higher ● PROFINET from GSD version/GSD revision GSDML V2.3 Operating mode ● DI Yes ● Counter No ● Oversampling No ● MSI No Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Input current Current consumption, max. 70 mA; All channels are supplied from the encoder supply Encoder supply Number of outputs 8 Output voltage, min. 19.2 V Short-circuit protection Yes; per module 24 V encoder supply ● 24 V Yes ● Short-circuit protection Yes ● Output current per channel, max. 700 mA ● Output current per module, max. 700 mA 6ES71316BF012AA0 Page 1/2 12.19.2020 Subject to change without notice © Copyright Siemens Power loss Power loss, typ. 1.6 W; 24 V, 8 inputs supplied via encoder supply Address area Address space per module ● Inputs 1 byte Hardware configuration Automatic encoding Yes ● Mechanical coding element Yes ● Type of mechanical coding element Type A Selection of BaseUnit for connection variants ● 1-wire connection BU type A0 ● 2-wire connection BU type A0 ● 3-wire connection BU type A0 with AUX terminals ● 4-wire connection BU type A0 + Potential distributor module Digital inputs Number of digital inputs 8 Digital inputs, parameterizable Yes Input characteristic curve in accordance with IEC 61131, type 1 Yes Input characteristic curve in accordance with IEC 61131, type 2 Yes Input characteristic curve in accordance with IEC 61131, type 3 Yes Input voltage ● Rated value (DC) 24 V — 24 V DC Yes ● for signal "0" -30 to +5 V ● for signal "1" +11 to +30V Input current ● for signal "1", typ. 6.8 mA Input delay (for rated value of input voltage) for standard inputs — parameterizable Yes; 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay of 30 to 500 µs, depending on line length) — at "0" to "1", min. 0.05 ms — at "0" to "1", max. 20 ms — at "1" to "0", min. 0.05 ms — at "1" to "0", max. 20 ms Cable length ● shielded, max. 1 000 m ● unshielded, max. 600 m Encoder Connectable encoders ● 2-wire sensor — permissible quiescent current (2-wire sensor), max. Yes 2 mA Interrupts/diagnostics/status information Diagnostics function Yes Alarms ● Diagnostic alarm Yes Diagnoses ● Diagnostic information readable Yes ● Monitoring the supply voltage Yes — parameterizable Yes ● Monitoring of encoder power supply No ● Wire-break No ● Short-circuit No ● Group error Yes Diagnostics indication LED 6ES71316BF012AA0 Page 2/3 12.19.2020 Subject to change without notice © Copyright Siemens ● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED ● Channel status display Yes; green LED ● for channel diagnostics No ● for module diagnostics Yes; green/red DIAG LED Potential separation Potential separation channels ● between the channels No ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics No Isolation Isolation tested with 707 V DC (type test) Ambient conditions Ambient temperature during operation ● horizontal installation, min. -30 °C; < 0 °C as of FS03 ● horizontal installation, max. 60 °C ● vertical installation, min. -30 °C; < 0 °C as of FS03 ● vertical installation, max. 50 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual Dimensions Width 15 mm Height 73 mm Depth 58 mm Weights Weight, approx. 28 g last modified: 12/3/2020 6ES71316BF012AA0 Page 3/3 12.19.2020 Subject to change without notice © Copyright Siemens