6ES7132-6HD01-0BB1

Data sheet 6ES7132-6HD01-0BB1 SIMATIC ET 200SP, Relay module, RQ NO 4x 120V DC..230VAC/5A ST. 4 normally open contacts, isolated contacts, packing unit: 1 piece, fits to BU-type B0 and B1, Colour Code CC40, substitute value output, module diagnostics for: supply voltage General information Product type designation RQ 4x120 VDC ... 230 VAC/5 A NO ST HW functional status From FS02 Firmware version V0.0 ● FW update possible No usable BaseUnits BU type B0, B1 Color code for module-specific color identification plate CC40 Product function ● I&M data Yes; I&M0 to I&M3 ● Isochronous mode No Engineering with ● STEP 7 TIA Portal configurable/integrated from version V14 ● STEP 7 configurable/integrated from version V5.5 SP3 ● PCS 7 configurable/integrated from version V8.1 SP1 ● PROFIBUS from GSD version/GSD revision One GSD file each, Revision 3 and 5 and higher ● PROFINET from GSD version/GSD revision GSDML V2.3 Operating mode ● DQ Yes ● DQ with energy-saving function No ● PWM No ● Oversampling No ● MSO No Redundancy ● Redundancy capability Yes Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Input current Current consumption (rated value) 55 mA; without load output voltage / header Rated value (AC) 230 V Power loss Power loss, typ. 1.5 W Address area Address space per module ● Inputs + 1 byte for QI information ● Outputs 1 byte Hardware configuration 6ES71326HD010BB1 Page 1/3 5/22/2024 Subject to change without notice © Copyright Siemens Automatic encoding Yes ● Mechanical coding element Yes ● Type of mechanical coding element type C Selection of BaseUnit for connection variants ● 2-wire connection BU type B1 ● 3-wire connection BU type B0 Digital outputs Type of digital output Relays Number of digital outputs 4 Current-sinking Yes Current-sourcing Yes Digital outputs, parameterizable Yes Short-circuit protection No Parallel switching of two outputs ● for logic links Yes ● for uprating No ● for redundant control of a load Yes Switching frequency ● with resistive load, max. 2 Hz ● with inductive load (acc. to IEC 60947-5-1, DC13), max. 0.5 Hz ● with inductive load (acc. to IEC 60947-5-1, AC15), max. 0.5 Hz ● on lamp load, max. 2 Hz Total current of the outputs ● Current per channel, max. 5A ● Current per module, max. 20 A Total current of the outputs (per module) horizontal installation — up to 50 °C, max. 20 A — up to 60 °C, max. 16 A vertical installation — up to 40 °C, max. 20 A — up to 50 °C, max. 16 A Relay outputs ● Number of relay outputs 4 ● Rated supply voltage of relay coil L+ (DC) 24 V ● Current consumption of relays (coil current of all relays), max. 40 mA ● external protection for relay outputs Yes, with miniature fuse max. 6 A tripping current and quick-response tripping characteristic ● Number of operating cycles, max. 7 000 000; see additional description in the manual Switching capacity of contacts — with inductive load, max. 2 A; see additional description in the manual — with resistive load, max. 5 A; see additional description in the manual — Thermal continuous current, max. 5 A; Max. 1 385 VA, 150 W — Switching current, min. 100 mA; 5 V DC — Rated switching voltage (DC) 24 V DC to 120 V DC — Rated switching voltage (AC) 24V AC to 230V AC Cable length ● shielded, max. 1 000 m ● unshielded, max. 200 m Interrupts/diagnostics/status information Diagnostics function Yes Substitute values connectable Yes Alarms ● Diagnostic alarm Yes Diagnoses ● Monitoring the supply voltage Yes ● Wire-break No ● Short-circuit No Diagnostics indication LED ● Monitoring of the supply voltage (PWR-LED) 6ES71326HD010BB1 Page 2/3 Yes; green PWR LED 5/22/2024 Subject to change without notice © Copyright Siemens ● Channel status display Yes; green LED ● for channel diagnostics No ● for module diagnostics Yes; green/red DIAG LED Potential separation Potential separation channels ● between the channels Yes ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics Yes Permissible potential difference between channels and backplane bus/supply voltage 240 V AC Isolation Isolation tested with 2 500 V DC (type test) tested with ● between channels and backplane bus/supply voltage 2 500 V DC ● between backplane bus and supply voltage 707 V DC (type test) Standards, approvals, certificates Suitable for safety functions No Ambient conditions Ambient temperature during operation ● horizontal installation, min. -30 °C ● horizontal installation, max. 60 °C ● vertical installation, min. -30 °C ● vertical installation, max. 50 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 2 000 m; On request: Installation altitudes greater than 2 000 m Dimensions Width 20 mm Height 73 mm Depth 58 mm Weights Weight, approx. 40 g last modified: 5/22/2024 6ES71326HD010BB1 Page 3/3 5/22/2024 Subject to change without notice © Copyright Siemens