6ES71326FD000CU0

Data sheet 6ES7132-6FD00-0CU0 SIMATIC ET 200SP, digital output module DQ 4x 24..230V AC/2A HF packaging unit: 1 piece, two alternative modes: DQ and power control, fits to BU-Type U0, color code CC20, channel diagnosis General information Product type designation DQ 4x24 ... 230 V AC/2 A HF, PU 1 HW functional status From FS03 Firmware version ● FW update possible usable BaseUnits Yes BU type U0 Product function ● I&M data Yes; I&M0 to I&M3 ● Isochronous mode No Engineering with ● STEP 7 TIA Portal configurable/integrated from version V14 ● STEP 7 configurable/integrated from version STEP 7 V5.5 or higher ● PROFIBUS from GSD version/GSD revision GSD as of Revision 5 ● PROFINET from GSD version/GSD revision GSDML V2.3 Operating mode ● DQ Yes ● DQ with energy-saving function Yes ● PWM No ● Oversampling No ● MSO No ● Phase control Yes ● Trailing-edge phase No ● Half-wave Yes ● Full-wave Yes Supply voltage Rated value (AC) 230 V permissible range, lower limit (AC) 20.4 V permissible range, upper limit (AC) 264 V Input current Current consumption (rated value) 8 mA Output voltage Rated value (AC) 230 V; 24V AC to 230V AC Power loss Power loss, typ. 9 W; Active power, load voltage 230 V, all outputs loaded with 2 A, 50 Hz Address area Address space per module 6ES71326FD000CU0 Page 1/2 12.20.2020 Subject to change without notice © Copyright Siemens ● Inputs + 1 byte for QI information ● Outputs 8 byte Hardware configuration Automatic encoding ● Mechanical coding element Yes Yes Selection of BaseUnit for connection variants ● 1-wire connection BU type U0 ● 2-wire connection BU type U0 ● 3-wire connection BU type U0 + Potential distributor module Digital outputs Number of digital outputs 4 Current-sinking No Current-sourcing Yes Digital outputs, parameterizable Yes Short-circuit protection No; external fusing necessary Open-circuit detection Yes; channel by channel ● Response threshold, typ. 1 mA; 40 V AC or more Overload protection No; A miniature fuse with 10 tripping current and tripping characteristic "quick response" must be provided in the module supply Controlling a digital input Yes Switching capacity of the outputs ● with resistive load, max. 2 A; Max. 4 A, see additional description in manual ● with inductive load, max. 2A ● on lamp load, max. 100 W; Tungsten rating in accordance with UL; for thermistors with higher power ratings, see the notes in the manual Output voltage ● for signal "1", min. 20.4 V Output current ● for signal "1" rated value 2A ● for signal "1" permissible range, min. 10 mA ● for signal "1" permissible range, max. 4 A; note derating data in the manual ● for signal "0" residual current, max. 3 mA Output delay with resistive load ● "0" to "1", max. 40 ms; 2 AC cycles ● "1" to "0", max. 20 ms; 1 AC cycle Parallel switching of two outputs ● for logic links No ● for uprating No ● for redundant control of a load Yes Switching frequency ● with resistive load, max. 10 Hz; Applies to DQ mode; limited by line frequency in PC mode ● with inductive load (acc. to IEC 60947-5-1, AC15), max. 10 Hz; Applies to DQ mode; limited by line frequency in PC mode ● on lamp load, max. 1 Hz; Applies to DQ mode; limited by line frequency in PC mode Total current of the outputs ● Current per channel, max. 2 A; Max. 4 A, see additional description in manual ● Current per module, max. 8A Total current of the outputs (per module) horizontal installation — up to 40 °C, max. 8A — up to 50 °C, max. 6A — up to 60 °C, max. 4A vertical installation — up to 30 °C, max. 8A — up to 40 °C, max. 6A — up to 50 °C, max. 4A Cable length ● shielded, max. 1 000 m ● unshielded, max. 600 m 6ES71326FD000CU0 Page 2/3 12.20.2020 Subject to change without notice © Copyright Siemens Interrupts/diagnostics/status information Diagnostics function Yes Substitute values connectable Yes Alarms ● Diagnostic alarm Yes Diagnoses ● Diagnostic information readable Yes ● Monitoring the supply voltage Yes ● Wire-break Yes; channel by channel ● Short-circuit No ● Group error Yes Diagnostics indication LED ● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED ● Channel status display Yes; green LED ● for channel diagnostics Yes; red Fn LED ● for module diagnostics Yes; green/red DIAG LED Potential separation Potential separation channels ● between the channels No ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics No Isolation Isolation tested with 2 545 V DC/2 s (routine test) Standards, approvals, certificates Suitable for safety functions No Ambient conditions Ambient temperature during operation ● horizontal installation, min. -30 °C ● horizontal installation, max. 60 °C ● vertical installation, min. -30 °C ● vertical installation, max. 50 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 2 000 m; On request: Installation altitudes greater than 2 000 m Dimensions Width 20 mm Height 73 mm Depth 58 mm Weights Weight, approx. 50 g last modified: 9/15/2020 6ES71326FD000CU0 Page 3/3 12.20.2020 Subject to change without notice © Copyright Siemens