6ES71346GD010BA1

Data sheet 6ES7134-6GD01-0BA1 SIMATIC ET 200SP, ANALOG INPUT MODULE, AI 4XI 2-/4-WIRE STANDARD, PACKING UNIT: 1 PIECE, FITS TO BU-TYPE A0, A1, COLOR CODE CC03, MODULE DIAGNOSIS, 16BIT, +/-0,3% General information Product type designation AI 4xI 2-/4-wire ST HW functional status From FS02 Firmware version ● FW update possible Yes usable BaseUnits BU type A0, A1 Color code for module-specific color identification plate CC03 Product function ● I&M data Yes; I&M0 to I&M3 ● Isochronous mode No ● Measuring range scalable No Engineering with ● STEP 7 TIA Portal configurable/integrated from version V14 / - ● STEP 7 configurable/integrated from version V5.6 and higher ● PCS 7 configurable/integrated from version V8.1 SP1 ● PROFIBUS from GSD version/GSD revision One GSD file each, Revision 3 and 5 and higher ● PROFINET from GSD version/GSD revision GSDML V2.3 Operating mode ● Oversampling No ● MSI No CiR - Configuration in RUN Reparameterization possible in RUN Yes Calibration possible in RUN No Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Input current Current consumption, max. 37 mA; without sensor supply Encoder supply 24 V encoder supply ● 24 V Yes ● Short-circuit protection Yes ● Output current, max. 20 mA; max. 50 mA per channel for a duration < 10 s Power loss 6ES71346GD010BA1 Page 1/2 12.17.2020 Subject to change without notice © Copyright Siemens Power loss, typ. 0.85 W; Without encoder supply voltage Address area Address space per module ● Address space per module, max. 8 byte; + 1 byte for QI information Hardware configuration Automatic encoding Yes ● Mechanical coding element Yes ● Type of mechanical coding element Type A Selection of BaseUnit for connection variants ● 2-wire connection BU type A0, A1 ● 4-wire connection BU type A0, A1 Analog inputs Number of analog inputs 4; Differential inputs permissible input current for current input (destruction limit), max. 50 mA Cycle time (all channels), min. Sum of the basic conversion times and additional processing times (depending on the parameterization of the active channels) Input ranges (rated values), currents ● 0 to 20 mA — Input resistance (0 to 20 mA) ● -20 mA to +20 mA — Input resistance (-20 mA to +20 mA) ● 4 mA to 20 mA — Input resistance (4 mA to 20 mA) Yes; 16 bit incl. sign 100 Ω; + approx. 0.7 V diode forward voltage in 2-wire operation Yes 100 Ω Yes; 15 bit 100 Ω; + approx. 0.7 V diode forward voltage in 2-wire operation Cable length ● shielded, max. 1 000 m Analog value generation for the inputs Measurement principle integrating (Sigma-Delta) Integration and conversion time/resolution per channel ● Resolution with overrange (bit including sign), max. 16 bit ● Integration time, parameterizable Yes ● Interference voltage suppression for interference frequency f1 in Hz 16.6 / 50 / 60 Hz ● Conversion time (per channel) 180 / 60 / 50 ms Smoothing of measured values ● Number of smoothing levels 4; None; 4/8/16 times ● parameterizable Yes Encoder Connection of signal encoders ● for voltage measurement No ● for current measurement as 2-wire transducer Yes — Burden of 2-wire transmitter, max. ● for current measurement as 4-wire transducer 650 Ω Yes Errors/accuracies Linearity error (relative to input range), (+/-) 0.01 % Temperature error (relative to input range), (+/-) 0.005 %/K Crosstalk between the inputs, min. 50 dB; Applies to up to ±5 V overvoltage in other channels Repeat accuracy in steady state at 25 °C (relative to input range), (+/-) 0.05 % Operational error limit in overall temperature range ● Current, relative to input range, (+/-) 0.5 % Basic error limit (operational limit at 25 °C) ● Current, relative to input range, (+/-) 0.3 % Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency ● Series mode interference (peak value of interference < rated value of input range), min. 70 dB ● Common mode voltage, max. 10 V ● Common mode interference, min. 90 dB 6ES71346GD010BA1 Page 2/3 12.17.2020 Subject to change without notice © Copyright Siemens Interrupts/diagnostics/status information Diagnostics function Yes Alarms ● Diagnostic alarm Yes ● Limit value alarm No Diagnoses ● Monitoring the supply voltage Yes ● Wire-break Yes; at 4 to 20 mA ● Short-circuit Yes; 2-wire mode: Short-circuit of the encoder supply to ground or of an input to the encoder supply ● Group error Yes ● Overflow/underflow Yes Diagnostics indication LED ● Monitoring of the supply voltage (PWR-LED) Yes; green LED ● Channel status display Yes; green LED ● for channel diagnostics No ● for module diagnostics Yes; green/red LED Potential separation Potential separation channels ● between the channels Yes; channel group-specific between 2-wire current input group and 4wire voltage input group ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics Yes; only for 4-wire transducer Permissible potential difference between the inputs (UCM) 10 V DC Isolation Isolation tested with 707 V DC (type test) Ambient conditions Ambient temperature during operation ● horizontal installation, min. -30 °C; < 0 °C as of FS02 ● horizontal installation, max. 60 °C ● vertical installation, min. -30 °C; < 0 °C as of FS02 ● vertical installation, max. 50 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual Dimensions Width 15 mm Height 73 mm Depth 58 mm Weights Weight, approx. 31 g last modified: 6/18/2020 6ES71346GD010BA1 Page 3/3 12.17.2020 Subject to change without notice © Copyright Siemens