6ES7136-6BA00-0CA0

Data sheet 6ES7136-6BA00-0CA0 SIMATIC DP, Electronics module for ET 200SP, F-DI 8x 24 V DC HF, 15 mm width, up to PL E (ISO 13849-1)/ SIL3 (IEC 61508) General information Product type designation F-DI 8x24VDC HF usable BaseUnits BU type A0 Product function ● I&M data Yes; I&M0 to I&M3 Engineering with ● STEP 7 TIA Portal configurable/integrated from version V12 ● STEP 7 configurable/integrated from version V5.5 SP3 / - ● PROFINET from GSD version/GSD revision V2.31 Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 20.4 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes power supply according to NEC Class 2 required No Input current Current consumption (rated value) 75 mA; without load Current consumption, max. 21 mA; From the backplane bus Encoder supply Number of outputs 8 Short-circuit protection Yes; Electronic (response threshold 0.7 A to 1.8 A) Output current ● up to 60 °C, max. 0.3 A 24 V encoder supply ● 24 V Yes; min. L+ (-1.5 V) ● Short-circuit protection Yes ● Output current, max. 800 mA; Total current of all encoders Power Power available from the backplane bus 70 mW Power loss Power loss, typ. 4W Address area Address space per module ● Inputs 6 byte ● Outputs 4 byte Hardware configuration Automatic encoding ● Electronic coding element type F Yes Yes Digital inputs Number of digital inputs 6ES71366BA000CA0 Page 1/3 8 5/8/2024 Subject to change without notice © Copyright Siemens Source/sink input Yes; P-reading Input characteristic curve in accordance with IEC 61131, type 1 Yes Input voltage ● Rated value (DC) 24 V ● for signal "0" -30 to +5 V ● for signal "1" +15 to +30 V Input current ● for signal "1", typ. 3.7 mA Input delay (for rated value of input voltage) for standard inputs — parameterizable Yes — at "0" to "1", min. 0.4 ms — at "0" to "1", max. 20 ms — at "1" to "0", min. 0.4 ms — at "1" to "0", max. 20 ms for technological functions — parameterizable No Cable length ● shielded, max. 1 000 m ● unshielded, max. 500 m Interrupts/diagnostics/status information Diagnostics function Yes Alarms ● Diagnostic alarm Yes ● Hardware interrupt No Diagnostics indication LED ● RUN LED Yes; green LED ● ERROR LED Yes; red LED ● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED ● Channel status display Yes; green LED ● for channel diagnostics Yes; red LED ● for module diagnostics Yes; green/red DIAG LED Potential separation Potential separation channels ● between the channels No ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics No Isolation Isolation tested with 707 V DC (type test) Standards, approvals, certificates Suitable for safety functions Yes Highest safety class achievable in safety mode ● Performance level according to ISO 13849-1 PLe ● SIL acc. to IEC 61508 SIL 3 Probability of failure (for service life of 20 years and repair time of 100 hours) — Low demand mode: PFDavg in accordance with SIL3 < 2.00E-05 — High demand/continuous mode: PFH in accordance with SIL3 < 1.00E-09 1/h Ambient conditions Ambient temperature during operation ● horizontal installation, min. 0 °C ● horizontal installation, max. 60 °C ● vertical installation, min. 0 °C ● vertical installation, max. 50 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 4 000 m; Restrictions for installation altitudes > 2 000 m, see manual Dimensions Width 15 mm Height 73 mm 6ES71366BA000CA0 Page 2/3 5/8/2024 Subject to change without notice © Copyright Siemens Depth 58 mm Weights Weight, approx. 49 g last modified: 3/12/2024 6ES71366BA000CA0 Page 3/3 5/8/2024 Subject to change without notice © Copyright Siemens