6ES7136-6DC00-0CA0

Data sheet 6ES7136-6DC00-0CA0 SIMATIC DP, electronic module ET 200SP, F-DQ 8x24VDC/0.5A PP HF, 15 mm width, up to PL E (ISO 13849) up to SIL 3 (IEC 61508) General information Product type designation F-DQ 8x24 V DC/0.5 A PP HF Firmware version ● FW update possible Yes usable BaseUnits BU type A0 Color code for module-specific color identification plate CC02 Product function ● I&M data Yes; I&M0 to I&M3 Engineering with ● STEP 7 TIA Portal configurable/integrated from version V14 SP1 with HSP 202 ● STEP 7 configurable/integrated from version V5.5 SP4 HF5 ● PROFINET from GSD version/GSD revision V2.31 Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes power supply according to NEC Class 2 required No Input current Current consumption (rated value) 75 mA; without load Current consumption, max. 21 mA; From the backplane bus output voltage / header Rated value (DC) 24 V Power Power available from the backplane bus 70 mW Power loss Power loss, typ. 3W Address area Address space per module ● Inputs 6 byte; 5 bytes non-RIOforFA; 6 bytes RIOforFA ● Outputs 6 byte; 5 bytes non-RIOforFA; 6 bytes RIOforFA Hardware configuration Automatic encoding ● Electronic coding element type F Yes Yes Digital outputs Type of digital output Transistor Number of digital outputs 8 Digital outputs, parameterizable Yes Short-circuit protection Yes ● Response threshold, typ. 6ES71366DC000CA0 Page 1/3 Min. 0.7 A 5/15/2024 Subject to change without notice © Copyright Siemens Open-circuit detection No Limitation of inductive shutdown voltage to Typ. -39 V Controlling a digital input Yes; digital output, according to IEC 61131-2, type 0.5 Switching capacity of the outputs ● with resistive load, max. 0.5 A ● on lamp load, max. 2W Load resistance range ● lower limit 48 Ω ● upper limit 12 000 Ω Output voltage ● for signal "1", min. 24 V; L+ (-0.5 V) Output current ● for signal "1" rated value 0.5 A ● for signal "0" residual current, max. 0.5 mA Switching frequency ● with resistive load, max. 30 Hz; Symmetrical ● with inductive load, max. 0.1 Hz; according to IEC 60947-5-1, DC-13, symmetrical ● with capacitive load, max. 2 Hz; Symmetrical ● on lamp load, max. 10 Hz; Symmetrical Total current of the outputs ● Current per channel, max. 0.5 A; note derating data in the manual ● Current per module, max. 3 A; note derating data in the manual Total current of the outputs (per module) horizontal installation — up to 40 °C, max. 3A — up to 50 °C, max. 2.5 A — up to 60 °C, max. 2A vertical installation — up to 50 °C, max. 2A Cable length ● shielded, max. 100 m ● unshielded, max. 100 m Interrupts/diagnostics/status information Diagnostics function Yes Substitute values connectable No Alarms ● Diagnostic alarm Yes Diagnostics indication LED ● RUN LED Yes; green LED ● ERROR LED Yes; red LED ● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED ● Channel status display Yes; green LED ● for channel diagnostics Yes; red LED ● for module diagnostics Yes; green/red DIAG LED Potential separation Potential separation channels ● between the channels No ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics No Isolation Isolation tested with 707 V DC (type test) Standards, approvals, certificates Suitable for safety functions Yes Highest safety class achievable in safety mode ● Performance level according to ISO 13849-1 PLe ● Category according to ISO 13849-1 Cat. 4 ● SIL acc. to IEC 61508 SIL 3 Probability of failure (for service life of 20 years and repair time of 100 hours) — Low demand mode: PFDavg in accordance with SIL3 6ES71366DC000CA0 Page 2/3 < 6.00E-05 5/15/2024 Subject to change without notice © Copyright Siemens — High demand/continuous mode: PFH in accordance with SIL3 < 2.00E-09 1/h Ambient conditions Ambient temperature during operation ● horizontal installation, min. 0 °C ● horizontal installation, max. 60 °C ● vertical installation, min. 0 °C ● vertical installation, max. 50 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 4 000 m; with derating Dimensions Width 15 mm Height 73 mm Depth 58 mm Weights Weight, approx. 48 g last modified: 3/12/2024 6ES71366DC000CA0 Page 3/3 5/15/2024 Subject to change without notice © Copyright Siemens