6ES71425AF000BA0

Data sheet 6ES7142-5AF00-0BA0 SIMATIC ET 200AL, DQ 8x 24 V DC/2 A, 8x M12, Degree of protection IP67 General information Product type designation DQ 8x24VDC/2A HW functional status FS03 Firmware version V1.0.x Product function ● I&M data Yes; I&M0 to I&M3 Engineering with ● STEP 7 TIA Portal configurable/integrated from version STEP 7 V13 SP1 or higher ● STEP 7 configurable/integrated from version V5.5 SP4 Hotfix 7 or higher ● PROFIBUS from GSD version/GSD revision GSD as of Revision 5 ● PROFINET from GSD version/GSD revision GSDML V2.3.1 Supply voltage power supply according to NEC Class 2 required No Load voltage 1L+ ● Rated value (DC) 24 V ● permissible range, lower limit (DC) 20.4 V ● permissible range, upper limit (DC) 28.8 V ● Reverse polarity protection Yes; against destruction; load increasing Load voltage 2L+ ● Rated value (DC) 24 V ● permissible range, lower limit (DC) 20.4 V ● permissible range, upper limit (DC) 28.8 V ● Reverse polarity protection Yes; against destruction; load increasing Input current Current consumption (rated value) 40 mA; without load from load voltage 1L+ (unswitched voltage) 4 A; Maximum value from load voltage 2L+, max. 4 A; Maximum value Power loss Power loss, typ. 4W Digital outputs Number of digital outputs ● in groups of Short-circuit protection ● Response threshold, typ. Limitation of inductive shutdown voltage to 8 4; 2 load groups for 4 outputs each Yes; per channel, electronic 2.8 A 2L+ (-47 V) Switching capacity of the outputs ● on lamp load, max. 10 W Load resistance range 6ES71425AF000BA0 Page 1/3 7/9/2022 Subject to change without notice © Copyright Siemens ● lower limit 12 Ω ● upper limit 4 kΩ Output voltage ● for signal "1", min. L+ (-0.8 V) Output current ● for signal "1" rated value 2A ● for signal "1" permissible range, max. 2 A; with inductive load to IEC 60947-5-1, DC-13 / AC-15 ● for signal "0" residual current, max. 0.5 mA Switching frequency ● with resistive load, max. 100 Hz ● with inductive load, max. 0.1 Hz; 0.25 Hz at 25 °C ● on lamp load, max. 1 Hz Total current of the outputs ● Current per group, max. 4 A; For inductive load max. 2 channels per group Cable length ● unshielded, max. 30 m Interrupts/diagnostics/status information Substitute values connectable Yes; channel by channel, parameterizable Alarms ● Diagnostic alarm Yes; Parameterizable Diagnoses ● Short-circuit Yes; Outputs to ground; module by module Diagnostics indication LED ● Channel status display Yes; green LED ● for module diagnostics Yes; green/red LED ● For load voltage monitoring Yes; green LED Potential separation between the load voltages Yes Potential separation channels ● between the channels, in groups of 4 ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics No; 4 channels are non-isolated and 4 channels are isolated from supply voltage 1L+ Isolation Isolation tested with 707 V DC (type test) Degree and class of protection IP degree of protection IP65/67 Standards, approvals, certificates Suitable for safety-related tripping of standard modules Yes; From FS01 Highest safety class achievable for safety-related tripping of standard modules ● Performance level according to ISO 13849-1 PL d ● Category according to ISO 13849-1 Cat. 3 ● SIL acc. to IEC 62061 SIL 2 Ambient conditions Ambient temperature during operation ● min. -30 °C ● max. 55 °C connection method / header Design of electrical connection for the inputs and outputs M12, 5-pole Design of electrical connection for supply voltage M8, 4-pole ET-Connection ● ET-Connection M8, 4-pin, shielded Dimensions Width 45 mm Height 159 mm Depth 40 mm Weights Weight, approx. 192 g last modified: 3/7/2022 6ES71425AF000BA0 Page 2/3 7/9/2022 Subject to change without notice © Copyright Siemens 6ES71425AF000BA0 Page 3/3 7/9/2022 Subject to change without notice © Copyright Siemens