6ES75221BH100AA0

Data sheet 6ES7522-1BH10-0AA0 SIMATIC S7-1500, digital output module, DQ16xDC 24V/0.5A BA, 16 channels in groups of 8, 4 A per group; the module supports the safetyoriented shutdown of load groups up to SIL2 according to EN IEC 62061:2021 and Category 3 / PL d according to EN ISO 13849-1:2015. delivery incl. front connector push-in General information Product type designation DQ 16x24VDC/0.5A BA HW functional status From FS01 Firmware version V1.0.0 ● FW update possible Yes Product function ● I&M data Yes; I&M0 to I&M3 ● Isochronous mode No ● Prioritized startup Yes Engineering with ● STEP 7 TIA Portal configurable/integrated from version V13 / V13 ● STEP 7 configurable/integrated from version V5.5 SP3 / - ● PROFIBUS from GSD version/GSD revision V1.0 / V5.1 ● PROFINET from GSD version/GSD revision V2.3 / - Operating mode ● DQ Yes ● DQ with energy-saving function No ● PWM No ● Oversampling No ● MSO Yes Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes; through internal protection with 7 A per group Input current Current consumption, max. 30 mA output voltage / header Rated value (DC) 24 V Power Power available from the backplane bus 1.15 W Power loss Power loss, typ. 2.2 W Digital outputs Type of digital output Transistor Number of digital outputs 16 Current-sourcing Yes Digital outputs, parameterizable No 6ES75221BH100AA0 Page 1/3 7/8/2022 Subject to change without notice © Copyright Siemens Short-circuit protection ● Response threshold, typ. Yes 1A Limitation of inductive shutdown voltage to L+ (-53 V) Controlling a digital input Yes Switching capacity of the outputs ● with resistive load, max. 0.5 A ● on lamp load, max. 5W Load resistance range ● lower limit 48 Ω ● upper limit 12 kΩ Output voltage ● for signal "1", min. L+ (-0.8 V) Output current ● for signal "1" rated value 0.5 A ● for signal "1" permissible range, max. 0.5 A ● for signal "0" residual current, max. 0.5 mA Output delay with resistive load ● "0" to "1", max. 100 µs ● "1" to "0", max. 500 µs Parallel switching of two outputs ● for logic links Yes ● for uprating No ● for redundant control of a load Yes Switching frequency ● with resistive load, max. 100 Hz ● with inductive load, max. 0.5 Hz; According to IEC 60947-5-1, DC-13 ● on lamp load, max. 10 Hz Total current of the outputs ● Current per channel, max. 0.5 A; see additional description in the manual ● Current per group, max. 4 A; see additional description in the manual ● Current per module, max. 8 A; see additional description in the manual Cable length ● shielded, max. 1 000 m ● unshielded, max. 600 m Interrupts/diagnostics/status information Diagnostics function No Substitute values connectable No Alarms ● Diagnostic alarm No ● Maintenance interrupt No Diagnoses ● Monitoring the supply voltage No ● Wire-break No ● Short-circuit No ● Group error No Diagnostics indication LED ● RUN LED Yes; green LED ● ERROR LED Yes; red LED ● Monitoring of the supply voltage (PWR-LED) Yes; green LED ● Channel status display Yes; green LED ● for channel diagnostics No ● for module diagnostics No Potential separation Potential separation channels ● between the channels No ● between the channels, in groups of 8 ● between the channels and backplane bus Yes Isolation Isolation tested with 6ES75221BH100AA0 Page 2/3 707 V DC (type test) 7/8/2022 Subject to change without notice © Copyright Siemens Standards, approvals, certificates Suitable for safety functions No Suitable for safety-related tripping of standard modules Yes; From FS02 Highest safety class achievable for safety-related tripping of standard modules ● Performance level according to ISO 13849-1 PL d ● Category according to ISO 13849-1 Cat. 3 ● SIL acc. to IEC 62061 SIL 2 ● remark on safety-oriented shutdown https://support.industry.siemens.com/cs/de/de/view/39198632 Ambient conditions Ambient temperature during operation ● horizontal installation, min. -30 °C; from FS04 ● horizontal installation, max. 60 °C ● vertical installation, min. -30 °C; from FS04 ● vertical installation, max. 40 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual Dimensions Width 25 mm Height 147 mm Depth 129 mm Weights Weight, approx. 230 g Other Note: Supplied incl. 40-pole push-in front connectors last modified: 5/6/2022 6ES75221BH100AA0 Page 3/3 7/8/2022 Subject to change without notice © Copyright Siemens