6ES7526-2BF00-0AB0.

Data sheet 6ES7526-2BF00-0AB0 SIMATIC S7-1500, F digital output module, F-DQ 8x 24 V DC 2A PPM PROFIsafe; 35 mm width; up to PL E (ISO 13849-1)/ SIL3 (IEC 61508) General information Product type designation F-DQ 8x24VDC/2A PPM Firmware version ● FW update possible Yes Product function ● I&M data Yes; I&M0 to I&M3 Engineering with ● STEP 7 TIA Portal configurable/integrated from version V13 SP1 with HSP 0086 Operating mode ● DQ Yes ● MSO No Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes power supply according to NEC Class 2 required No Input current Current consumption (rated value) 110 mA; without load Current consumption, max. 130 mA; without load output voltage / header Rated value (DC) 24 V Power Power available from the backplane bus 0.8 W Power loss Power loss, typ. 11 W Address area Address space per module ● Inputs 6 byte; S7-300/400F CPU, 5 byte ● Outputs 6 byte; S7-300/400F CPU, 5 byte Hardware configuration Automatic encoding ● Electronic coding element type F Yes Yes Digital outputs Number of digital outputs 8 Current-sinking Yes Current-sourcing Yes Short-circuit protection Yes Open-circuit detection Yes ● Response threshold, typ. 6ES75262BF000AB0 Page 1/3 8 mA 5/31/2024 Subject to change without notice © Copyright Siemens Overload protection ● Response threshold, typ. Yes 2.9 A Limitation of inductive shutdown voltage to PM-switching: -24 V + (-47 V), PP-switching: -24 V Controlling a digital input Yes; digital output, according to IEC 61131-2, type 2 Switching capacity of the outputs ● with resistive load, max. 2A ● on lamp load, max. 10 W Load resistance range ● lower limit 12 Ω ● upper limit 2 000 Ω Output voltage ● for signal "1", min. 24 V; L+ (-0.5 V) Output current ● for signal "1" rated value 2A ● for signal "0" residual current, max. 0.5 mA; Current-sourcing, or current sourcing and sinking switches individually, current sinking: max. 1 mA Switching frequency ● with resistive load, max. 30 Hz ● with inductive load, max. 0.1 Hz ● on lamp load, max. 10 Hz Total current of the outputs ● Current per channel, max. 2A Total current of the outputs (per module) horizontal installation — up to 40 °C, max. 16 A — up to 60 °C, max. 8A vertical installation — up to 40 °C, max. 8A Cable length ● shielded, max. 1 000 m ● unshielded, max. 500 m Interrupts/diagnostics/status information Diagnostics function Yes Substitute values connectable No Alarms ● Diagnostic alarm Yes Diagnoses ● Monitoring the supply voltage Yes ● Wire-break Yes ● Short-circuit Yes ● Group error Yes Diagnostics indication LED ● RUN LED Yes; green LED ● ERROR LED Yes; red LED ● Monitoring of the supply voltage (PWR-LED) Yes ● Channel status display Yes; green LED ● for channel diagnostics Yes; red LED ● for module diagnostics Yes; red LED Potential separation Potential separation channels ● between the channels No ● between the channels and backplane bus Yes Isolation Isolation tested with 707 V DC (type test) Standards, approvals, certificates Suitable for safety functions Yes Highest safety class achievable in safety mode ● Performance level according to ISO 13849-1 PLe ● SIL acc. to IEC 61508 SIL 3 Probability of failure (for service life of 20 years and repair time of 100 hours) — Low demand mode: PFDavg in accordance with 6ES75262BF000AB0 Page 2/3 < 6.00E-05 5/31/2024 Subject to change without notice © Copyright Siemens SIL3 — High demand/continuous mode: PFH in accordance with SIL3 < 2.00E-09 1/h Ambient conditions Ambient temperature during operation ● horizontal installation, min. 0 °C ● horizontal installation, max. 60 °C ● vertical installation, min. 0 °C ● vertical installation, max. 40 °C Dimensions Width 35 mm Height 147 mm Depth 129 mm Weights Weight, approx. 300 g last modified: 3/12/2024 6ES75262BF000AB0 Page 3/3 5/31/2024 Subject to change without notice © Copyright Siemens