6SL32201YE280UB0

Data sheet for SINAMICS G120X MLFB-Ordering data 6SL3220-1YE28-0UB0 Figure similar Client order no. : Item no. : Order no. : Consignment no. : Offer no. : Project : Remarks : Rated data General tech. specifications Input Number of phases 3 AC Line voltage 380 ... 480 V +10 % -20 % Line frequency 47 ... 63 Hz Rated voltage 400V IEC 480V NEC Rated current (LO) 29.50 A 29.50 A Rated current (HO) 23.97 A 24.50 A Output Number of phases 3 AC Rated voltage 400V IEC 480V NEC Rated power (LO) 15.00 kW 20.00 hp Rated power (HO) 11.00 kW 15.00 hp Rated current (LO) 32.00 A 27.00 A Rated current (HO) 26.00 A 21.00 A Rated current (IN) 33.00 A Max. output current 43.00 A Pulse frequency 4 kHz Output frequency for vector control 0 ... 200 Hz Output frequency for V/f control 0 ... 550 Hz Power factor λ 0.70 ... 0.85 Offset factor cos φ 0.96 Efficiency η 0.98 Sound pressure level (1m) 67 dB Power loss 0.396 kW Filter class (integrated) Unfiltered EMC category (with accessories) without Ambient conditions Standard board coating type Class 3C2, according to IEC 60721-33: 2002 Cooling Air cooling using an integrated fan Cooling air requirement 0.018 m³/s (0.653 ft³/s) Installation altitude 1000 m (3280.84 ft) Ambient temperature Operation -20 ... 45 °C (-4 ... 113 °F) Transport -40 ... 70 °C (-40 ... 158 °F) Storage -25 ... 55 °C (-13 ... 131 °F) Relative humidity Max. operation 95 % At 40 °C (104 °F), condensation and icing not permissible Overload capability Low Overload (LO) 110% base load current IL for 60 s in a 300 s cycle time High Overload (HO) 150% x base load current IH for 60 s within a 600 s cycle time Technical data are subject to change! There may be discrepancies between calculated and rating plate values. Page 1 of 3 Generated Thu Jan 14 13:26:36 CET 2021 Data sheet for SINAMICS G120X MLFB-Ordering data 6SL3220-1YE28-0UB0 Figure similar Mechanical data Degree of protection IP20 / UL open type Size FSC Net weight 7 kg (15.74 lb) Width 140 mm (5.51 in) Height 295 mm (11.61 in) Depth 218 mm (8.58 in) Inputs / outputs Standard digital inputs Number 6 Switching level: 0→1 11 V Switching level: 1→0 5V Max. inrush current 15 mA Closed-loop control techniques V/f linear / square-law / parameterizable Yes V/f with flux current control (FCC) Yes V/f ECO linear / square-law Yes Sensorless vector control Yes Vector control, with sensor No Encoderless torque control Yes Torque control, with encoder No Communication Communication USS, Modbus RTU, BACnet MS/TP Connections Signal cable Fail-safe digital inputs Number 1 Digital outputs Conductor cross-section 0.15 ... 1.50 mm² (AWG 24 ... AWG 16) Line side Number as relay changeover contact 2 Version screw-type terminal Output (resistive load) DC 30 V, 5.0 A Conductor cross-section 1.50 ... 16.00 mm² (AWG 16 ... AWG 6) Number as transistor 0 Analog / digital inputs Number 2 (Differential input) Resolution 10 bit Motor end Version Screw-type terminals Conductor cross-section 1.50 ... 16.00 mm² (AWG 16 ... AWG 6) DC link (for braking resistor) Switching threshold as digital input PE connection 0→1 4V 1→0 1.6 V Analog outputs Number On housing with M4 screw Max. motor cable length Shielded 150 m (492.13 ft) Unshielded 300 m (984.25 ft) 1 (Non-isolated output) PTC/ KTY interface 1 motor temperature sensor input, sensors that can be connected: PTC, KTY and Thermo-Click, accuracy ±5 °C Technical data are subject to change! There may be discrepancies between calculated and rating plate values. Page 2 of 3 Generated Thu Jan 14 13:26:36 CET 2021 Data sheet for SINAMICS G120X MLFB-Ordering data 6SL3220-1YE28-0UB0 Figure similar Converter losses to EN 50598-2* Efficiency class IE2 Comparison with the reference converter (90% / 100%) -35.40 % Standards I 100% 50% 25% 278.7 W (1.26 %) 324.6 W (1.46 %) 395.8 W (1.79 %) 173.9 W (0.78 %) 191.9 W (0.87 %) 216.3 W (0.98 %) 138.3 W (0.62 %) 146 W (0.66 %) 50% 90% Compliance with standards UL, cUL, CE, C-Tick (RCM), EAC, KCC, SEMI F47, REACH CE marking EMC Directive 2004/108/EC, Low-Voltage Directive 2006/95/EC f The percentage values show the losses in relation to the rated apparent power of the converter. The diagram shows the losses for the points (as per standard EN 50598) of the relative torque generating current (I) over the relative motor stator frequency(f). The values are valid for the basic version of the converter without options/components. *converted values Technical data are subject to change! There may be discrepancies between calculated and rating plate values. Page 3 of 3 Generated Thu Jan 14 13:26:36 CET 2021