6SL32201YH580CF0

Data sheet for SINAMICS G120X MLFB-Ordering data 6SL3220-1YH58-0CF0 Figure similar Client order no. : Item no. : Order no. : Consignment no. : Offer no. : Project : Remarks : Rated data General tech. specifications Input Number of phases 3 AC Line voltage 500 ... 690 V +10 % -10 % Line frequency 47 ... 63 Hz Rated voltage 690V IEC 600V NEC Rated current (LO) 416.00 A 408.00 A Rated current (HO) 327.00 A 333.00 A Output Number of phases 3 AC Rated voltage 690V IEC 600V NEC Rated power (LO) 355.00 kW 400.00 hp Rated power (HO) 315.00 kW 350.00 hp Rated current (LO) 385.00 A 388.00 A Rated current (HO) 330.00 A 320.00 A Rated current (IN) 400.00 A Max. output current 529.00 A Pulse frequency 2 kHz Output frequency for vector control 0 ... 100 Hz Output frequency for V/f control 0 ... 100 Hz Power factor λ 0.75 ... 0.93 Offset factor cos φ 0.96 Efficiency η 0.98 Sound pressure level (1m) 74 dB Power loss 6.191 kW Filter class (integrated) RFI suppression filter for Category C3 EMC category (with accessories) Category C3 Ambient conditions Standard board coating type Class 3C2, according to IEC 60721-33: 2002 Cooling Air cooling using an integrated fan Cooling air requirement 0.362 m³/s (12.784 ft³/s) Installation altitude 1000 m (3280.84 ft) Ambient temperature Operation 0 ... 45 °C (32 ... 113 °F) Transport -40 ... 70 °C (-40 ... 158 °F) Storage -25 ... 55 °C (-13 ... 131 °F) Relative humidity Max. operation 95 % At 40 °C (104 °F), condensation and icing not permissible Overload capability Low Overload (LO) 110% base load current IL for 60 s in a 300 s cycle time High Overload (HO) 150% x base load current IH for 60 s within a 600 s cycle time Technical data are subject to change! There may be discrepancies between calculated and rating plate values. Page 1 of 3 Generated Thu Jan 14 13:13:29 CET 2021 Data sheet for SINAMICS G120X MLFB-Ordering data 6SL3220-1YH58-0CF0 Figure similar Mechanical data Degree of protection IP20 / UL open type Size FSH Net weight 158 kg (348.33 lb) Width 548 mm (21.57 in) Height 1695 mm (66.73 in) Depth 393 mm (15.47 in) Inputs / outputs Standard digital inputs Number 6 Switching level: 0→1 11 V Switching level: 1→0 5V Max. inrush current 15 mA Closed-loop control techniques V/f linear / square-law / parameterizable Yes V/f with flux current control (FCC) Yes V/f ECO linear / square-law Yes Sensorless vector control Yes Vector control, with sensor No Encoderless torque control Yes Torque control, with encoder No Communication Communication PROFINET, EtherNet/IP Connections Signal cable Fail-safe digital inputs Number 1 Digital outputs Conductor cross-section 0.15 ... 1.50 mm² (AWG 24 ... AWG 16) Line side Number as relay changeover contact 2 Version M12 screw Output (resistive load) DC 30 V, 5.0 A Conductor cross-section 240.00 mm² (MCM 2 x 500 ... MCM 4 x 500) Number as transistor 0 Analog / digital inputs Number 2 (Differential input) Resolution 10 bit Motor end Version M12 screw Conductor cross-section 240.00 mm² (MCM 2 x 500 ... MCM 4 x 500) DC link (for braking resistor) Switching threshold as digital input PE connection 0→1 4V 1→0 1.6 V M12 screw Max. motor cable length Shielded 150 m (492.13 ft) Analog outputs Number 1 (Non-isolated output) PTC/ KTY interface 1 motor temperature sensor input, sensors that can be connected: PTC, KTY and Thermo-Click, accuracy ±5 °C Technical data are subject to change! There may be discrepancies between calculated and rating plate values. Page 2 of 3 Generated Thu Jan 14 13:13:29 CET 2021 Data sheet for SINAMICS G120X MLFB-Ordering data 6SL3220-1YH58-0CF0 Figure similar Converter losses to EN 50598-2* Efficiency class IE2 Comparison with the reference converter (90% / 100%) -34.60 % Standards I 100% 50% 25% 5299.0 W (1.13 %) 5859.0 W (1.25 %) 6611.0 W (1.41 %) 2847.0 W (0.61 %) 3087.0 W (0.66 %) 3375.0 W (0.72 %) 2002.0 W (0.43 %) 2114 W (0.45 %) 50% 90% Compliance with standards UL, cUL, CE, C-Tick (RCM), EAC, KCC, SEMI F47, REACH CE marking EMC Directive 2004/108/EC, Low-Voltage Directive 2006/95/EC f The percentage values show the losses in relation to the rated apparent power of the converter. The diagram shows the losses for the points (as per standard EN 50598) of the relative torque generating current (I) over the relative motor stator frequency(f). The values are valid for the basic version of the converter without options/components. *converted values Technical data are subject to change! There may be discrepancies between calculated and rating plate values. Page 3 of 3 Generated Thu Jan 14 13:13:29 CET 2021